Provided by: inn2_2.6.1-4build1_amd64 
NAME
buffindexed.conf - Configuration for the buffindexed overview method
DESCRIPTION
buffindexed.conf, found in pathetc, specifies the buffers that the buffindexed overview
method should use. It is required if the server uses buffindexed (as configured by the
ovmethod parameter in inn.conf).
Buffindexed uses pre-built buffer files to store overview data and indexes to that data.
The buffers are divided into 8 KB internally, and a given block is used either for
overview data or for index data. A block is always allocated to a single newsgroup and is
never shared among newsgroups.
In addition to the buffers, buffindexed also stores information in a file named
group.index in pathdb. (This file should not be mistaken for the one named group.index in
pathoverview which is used by the tradindexed overview method.) It contains information
about each newsgroup: the pointer to the index block for the newsgroup, the high mark,
the low mark, the flag of the group, the number of articles, and so forth. This file is
created automatically when all buffers are initialized and should not be manually edited.
Buffindexed buffers are of fixed size, so buffindexed will never use more space than what
is available in those buffers. If all buffers are full, innd will throttle when it
attempts to store overview information for any additional articles until space is freed
(with expireover, for instance) or another buffer is added. This is unlike the CNFS
storage method.
You can see the current usage of the buffers with the -o option to inndf.
In the buffindexed.conf file, blank lines and lines beginning with a number sign ("#") are
ignored. All other lines must be of the format:
<index>:<filename>:<size>
The order of lines is not significant.
<index> is the index of this overview buffer and must be unique. Other than that
constraint, it can be any number between 0 and 65535.
<filename> is the path to the buffer. The length of the path should not be longer than 63
characters.
<size> is the length of the buffer in kilobytes (1 KB = 1024 bytes). If <filename> does
not specify a special device, the file size of the buffer must be <size> * 1024 bytes. If
it does specify a special device, that device must have at least <size> space available.
For more information on setting up the buffers, see "CREATING BUFFERS".
An example of buffindexed.conf file can be:
0:<pathoverview in inn.conf>/OV1:1536000
1:<pathoverview in inn.conf>/OV2:1536000
When you first start innd with everything configured properly, you should see messages
like this in pathlog/news.notice:
Aug 27 00:00:00 kevlar innd: buffindexed: no magic cookie found
for ovbuff 0, initializing
You MUST recreate overview completely using makehistory if you remove or replace buffers.
However, new buffers can be added without any special care (other than restarting innd
after modifying buffindexed.conf). If you need to rebuild overview, you should zero all
of the buffers first.
CREATING BUFFERS
There are two methods to create a new buffindexed buffer:
1. Create a large file on top of a regular file system. The easiest way to do this is
probably with dd(1), using a command like:
dd if=/dev/zero of=/path/to/cycbuff bs=1024 count=<size>
where <size> is the size from the relevant line in buffindexed.conf.
This is the simplest method, but has the disadvantage that very large files on regular
file systems can be fairly slow to access, particularly at the end of the file, and
INN incurs unnecessary file system overhead when accessing the buffer.
2. Use block devices directly. If your operating system allows you to call mmap() on
block devices (Solaris and recent versions of Linux do, FreeBSD at last report does
not), this method can avoid all of the native file system overhead. Note, however,
that Solaris has problems with byte range locking on block devices, and therefore this
method should not be used on Solaris.
Partition the disk. If you're using Solaris, set up your partitions to avoid the
first cylinder of the disk (or otherwise the buffindexed header will overwrite the
disk partition table and render the buffers inaccessible). Then, create device files
for each block device you're going to use.
It's not recommended to use the block device files in /dev, since the news system
doesn't have permission to write to them and changing the permissions of the system
device files may affect something else. Instead, use mknod(1) to create a new set of
block devices (in somewhere like pathspool/overview that's only writable by the news
user). To do this, run "ls -Ll" on the devices in /dev that correspond to the block
devices that you want to use. The major and minor device numbers are in the fifth and
sixth columns (right before the date), respectively. Then run mknod like:
mknod <filename> b <major> <minor>
where <filename> is the path to the device to create (matching the <filename> part of
the buffindexed configuration line) and <major> and <minor> are the major and minor
device numbers as discovered above.
Here's a short script to do this when given the path to the system device file as an
argument:
#!/bin/sh
base=`echo "$1" | sed 's%.*/%%'`
major=`ls -Ll "$1" | awk '{print $5}' | tr -d ,`
minor=`ls -Ll "$1" | awk '{print $6}`
mkdir -p <pathoverview in inn.conf>
mknod <pathoverview>/"$base" b "$major" "$minor"
chown news:news <pathoverview>/"$base"
chmod 644 <pathoverview>/"$base"
Make sure that the created files are owned by the news user and news group, as
specified at configure time (the default being "news" for both). Also make sure that
the permissions on the devices allow the news user to read and write.
HISTORY
Written by Katsuhiro Kondou <kondou@nec.co.jp> for InterNetNews. Converted to POD by Russ
Allbery <eagle@eyrie.org>.
$Id: buffindexed.conf.pod 9925 2015-08-08 17:05:43Z iulius $
SEE ALSO
expireover(8), inn.conf(5), inndf(8), makehistory(8).