NAME

       rsocket - RDMA socket API

SYNOPSIS

       #include <rdma/rsocket.h>

DESCRIPTION

       RDMA socket API and protocol

NOTES

       Rsockets  is  a  protocol  over  RDMA  that  supports a socket-level API for applications.
       Rsocket APIs are intended to match the behavior  of  corresponding  socket  calls,  except
       where  noted.   Rsocket  functions  match the name and function signature of socket calls,
       with the exception that all function calls are prefixed with an 'r'.

       The following functions are defined:

       rsocket

       rbind, rlisten, raccept, rconnect

       rshutdown, rclose

       rrecv, rrecvfrom, rrecvmsg, rread, rreadv

       rsend, rsendto, rsendmsg, rwrite, rwritev

       rpoll, rselect

       rgetpeername, rgetsockname

       rsetsockopt, rgetsockopt, rfcntl

       Functions take the same parameters as that used for sockets.  The follow capabilities  and
       flags are supported at this time:

       PF_INET, PF_INET6, SOCK_STREAM, SOCK_DGRAM

       SOL_SOCKET   -   SO_ERROR,   SO_KEEPALIVE   (flag   supported,  but  ignored),  SO_LINGER,
       SO_OOBINLINE, SO_RCVBUF, SO_REUSEADDR, SO_SNDBUF

       IPPROTO_TCP - TCP_NODELAY, TCP_MAXSEG

       IPPROTO_IPV6 - IPV6_V6ONLY

       MSG_DONTWAIT, MSG_PEEK, O_NONBLOCK

       Rsockets provides extensions beyond normal socket routines that allow for direct placement
       of data into an application's buffer.  This is also known as zero-copy support, since data
       is sent and received directly, bypassing copies  into  network  controlled  buffers.   The
       following calls and options support direct data placement.

       riomap, riounmap, riowrite

       off_t riomap(int socket, void *buf, size_t len, int prot, int flags, off_t offset)

       Riomap registers an application buffer with the RDMA hardware
              associated  with an rsocket.  The buffer is registered either for local only access
              (PROT_NONE) or for remote write access (PROT_WRITE).  When  registered  for  remote
              access,  the  buffer is mapped to a given offset.  The offset is either provided by
              the user, or if the user selects -1 for the  offset,  rsockets  selects  one.   The
              remote  peer  may  access  an  iomapped  buffer  directly by specifying the correct
              offset.  The mapping is not guaranteed to be available until after the remote  peer
              receives a data transfer initiated after riomap has completed.

       In  order  to enable the use of remote IO mapping calls on an rsocket, an application must
       set the number of IO mappings that are available to the remote peer.   This  may  be  done
       using  the  rsetsockopt  RDMA_IOMAPSIZE  option.   By default, an rsocket does not support
       remote IO mappings.  riounmap

       int riounmap(int socket, void *buf, size_t len)

       Riounmap removes the mapping between a buffer and an rsocket.

       riowrite

       size_t riowrite(int socket, const void *buf, size_t count, off_t offset, int flags)

       Riowrite allows an application to transfer data over an rsocket
              directly into a remotely iomapped buffer.  The remote buffer is  specified  through
              an  offset  parameter,  which  corresponds  to  a remote iomapped buffer.  From the
              sender's perspective, riowrite behaves similar to rwrite.  From a receiver's  view,
              riowrite  transfers  are  silently  redirected  into a pre- determined data buffer.
              Data is received automatically, and the receiver is not informed of  the  transfer.
              However,  iowrite  data  is  still  considered  part  of the data stream, such that
              iowrite data will be written before a subsequent transfer is received.   A  message
              sent  immediately after initiating an iowrite may be used to notify the receiver of
              the iowrite.

       In addition to standard socket options, rsockets supports options specific to RDMA devices
       and  protocols.   These  options  are accessible through rsetsockopt using SOL_RDMA option
       level.

       RDMA_SQSIZE - Integer size of the underlying send queue.

       RDMA_RQSIZE - Integer size of the underlying receive queue.

       RDMA_INLINE - Integer size of inline data.

       RDMA_IOMAPSIZE - Integer number of remote IO mappings supported

       RDMA_ROUTE - struct ibv_path_data of path record for connection.

       Note that rsockets fd's cannot be passed into non-rsocket calls.  For  applications  which
       must mix rsocket fd's with standard socket fd's or opened files, rpoll and rselect support
       polling both rsockets and normal fd's.

       Existing applications can make use of rsockets through  the  use  of  a  preload  library.
       Because  rsockets  implements  an end-to-end protocol, both sides of a connection must use
       rsockets.  The rdma_cm library provides such a preload library, librspreload.   To  reduce
       the  chance  of  the  preload  library  intercepting  calls  without  the  user's explicit
       knowledge, the librspreload library is installed into %libdir%/rsocket subdirectory.

       The preload library can be used by setting LD_PRELOAD when running.   Note  that  not  all
       applications will work with rsockets.  Support is limited based on the socket options used
       by the application.  Support for fork() is limited, but available.  To use  rsockets  with
       the  preload  library  for  applications  that  call  fork, users must set the environment
       variable RDMAV_FORK_SAFE=1 on both the client and  server  side  of  the  connection.   In
       general,  fork  is supportable for server applications that accept a connection, then fork
       off a process to handle the new connection.

       rsockets uses configuration files that give an  administrator  control  over  the  default
       settings used by rsockets.  Use files under /etc/rdma/rsocket as shown:

       mem_default - default size of receive buffer(s)

       wmem_default - default size of send buffer(s)

       sqsize_default - default size of send queue

       rqsize_default - default size of receive queue

       inline_default - default size of inline data

       iomap_size - default size of remote iomapping table

       polling_time - default number of microseconds to poll for data before waiting

       All  configuration  files  should  contain  a  single integer value.  Values may be set by
       issuing a command similar to the following example.

       echo 1000000 > /etc/rdma/rsocket/mem_default

       If configuration files are not available, rsockets uses internal  defaults.   Applications
       can override default values programmatically through the rsetsockopt routine.

SEE ALSO

       rdma_cm(7)