Provided by: pptp-linux_1.9.0+ds-2_amd64 
NAME
pptp - PPTP driver
SYNOPSIS
pptp <pptp-server-IP> <pptp-options> [ppp-options] ...
DESCRIPTION
pptp establishes the client side of a Virtual Private Network (VPN) using the Point-to-Point Tunneling
Protocol (PPTP). Use this program to connect to an employer's PPTP based VPN, or to certain cable and
ADSL service providers.
By default, pptp establishes the PPTP call to the PPTP server, and then starts an instance of pppd to
manage the data transfer. However, pptp can also be run as a connection manager within pppd.
OPTIONS
The first non-option argument on the pptp command line must be the host name or IP address of the PPTP
server.
All long options (starting with "--") are interpreted as pptp options, and a fatal error occurs if an
unrecognised option is used.
All command-line arguments which do not start with "-" are interpreted as ppp options, and passed as is
to pppd unless --nolaunchpppd is given.
--phone <number>
Pass <number> to remote host as phone number
--nolaunchpppd
Do not launch pppd but use stdin as the network connection. Use this flag when including pptp as
a pppd connection process using the pty option. See EXAMPLES.
--quirks <quirk>
Work around a buggy PPTP implementation, adopts special case handling for particular PPTP servers
and ADSL modems. Currently recognised values are BEZEQ_ISRAEL only
--debug
Run in foreground (for debugging with gdb)
--sync Enable Synchronous HDLC (pppd must use it too)
--timeout <secs>
Time to wait for reordered packets (0.01 to 10 secs)
--nobuffer
Completely disables buffering and reordering of packets. Any --timeout specified will be ignored.
--idle-wait <secs>
Time to wait before sending a control connection echo request. The RFC2637 default is 60 seconds.
--max-echo-wait <secs>
Time to wait for an echo reply before closing the control connection. The RFC2637 default is 60
seconds.
--logstring <name>
Use <name> instead of 'anon' in syslog messages
--localbind <addr>
Bind to specified IP address instead of wildcard
--rtmark <n>
Use specified policy routing mark for all packets. This causes both the TCP control connection's
packets as well as the GRE packets to bear the given policy routing / netfilter mark. This can be
used with ip rule (from iproute2) to use a separate routing table for the pptp client.
(requires root privileges or the CAP_NET_ADMIN capability.)
--nohostroute
Do not configure a host route pointing towards the PPTP server. (cf. ROUTING below)
--loglevel <level>
Sets the debugging level (0=low, 1=default, 2=high)
--test-type <n>
Enable packet reordering tests that damage the integrity of the packet stream to the server. Use
this only when testing servers. Zero is the default, and means that packets are sent in the
correct order. A value of one (1) causes a single swap between two packets, such that the
sequence numbers might be 1 2 3 4 6 5 7 8 9. A value of two (2) causes ten packets to be
buffered, then sent out of order but ascending, such that the sequence numbers might be 1 2 3 4 16
6 7 8 9 10 11 12 13 14 15 17 18 19 20. A value of three (3) causes ten packets to be buffered,
then sent in the reverse order, like this; 1 2 3 4 16 15 14 13 12 11 10 9 8 7 6 5 17 18 19 20.
--test-rate <n>
Sets the number of packets to pass before causing a reordering test. Default is 100. Has no
effect if test-type is zero. The result of test types 2 and 3 are undefined if this value is less
than ten.
ROUTING
When PPTP is used in conjunction with a default route on top of the tunnel (or just any route
encompassing the PPTP server), the mechanics of routing would cause the PPTP packets themselves to be
routed over the tunnel. This would result in an encapsulation loop, destroying connectivity.
pptp by default works around this by looking up the route towards the PPTP server at startup and
configures a host route with that data. This essentially "freezes" routing for PPTP packets at the
startup configuration. This behaviour can be disabled with --nohostroute if undesired (like when using
--rtmark to implement policy routing).
NB: the route added by pptp is currently not deleted at exit!
QUIRKS
BEZEQ_ISRAEL
modifies packets to interoperate with Orckit ADSL modems on the BEZEQ network in Israel.
EXAMPLES
Connection to a Microsoft Windows VPN Server
pppd noauth nobsdcomp nodeflate require-mppe-128 name domain\\\\username remotename PPTP pty "pptp
10.0.0.5 --nolaunchpppd"
Note that the chap-secrets file used by pppd must include an entry for domain\\username
STATISTICS
The pptp process collects statistics when sending and receiving GRE packets. They are intended to be
useful for debugging poor PPTP performance and for general monitoring of link quality. The statistics are
cumulative since the pptp process was started.
The statistics can be viewed by sending a SIGUSR1 signal to the "GRE-to-PPP Gateway" process, which will
cause it to dump them to the system logs (at the LOG_NOTICE level). A better way to present the
statistics to applications is being sought (e.g. SNMP?).
The following statistics are collected at the time of writing (April 2003):
rx accepted
the number of GRE packets successfully passed to PPP
rx lost
the number of packets never received, and presumed lost in the network
rx under win
the number of packets which were duplicates or had old sequence numbers (this might be caused by a
packet-reordering network if your reordering timeout is set too low)
rx over win
the number of packets which were too far ahead in the sequence to be reordered (might be caused by
loss of more than 300 packets in a row)
rx buffered
the number of packets which were slightly ahead of sequence, and were either buffered for
reordering, or if buffering is disabled, accepted immediately (resulting in the intermediate
packets being discarded).
rx OS errors
the number of times where the operating system reported an error when we tried to read a packet
rx truncated
the number of times we received a packet which was shorter than the length implied by the GRE
header
rx invalid
the number of times we received a packet which had invalid or unsupported flags set in the header,
wrong version, or wrong protocol.
rx acks
the number of pure acknowledgements received (without data). Too many of these will waste
bandwidth, and might be solved by tuning the remote host.
tx sent
the number of GRE packets sent with data
tx failed
the number of packets we tried to send, but the OS reported an error
tx short
the number of times the OS would not let us write a complete packet
tx acks
the number of times we sent a pure ack, without data
tx oversize
the number of times we couldn't send a packet because it was over PACKET_MAX bytes long
round trip
the estimated round-trip time in milliseconds
SEE ALSO
pppd(8)
Documentation in /usr/share/doc/pptp-linux
AUTHOR
This manual page was written by James Cameron <james.cameron@hp.com> from text contributed by Thomas
Quinot <thomas@debian.org>, for the Debian GNU/Linux system. The description of the available statistics
was written by Chris Wilson <chris@netservers.co.uk>. Updates for the Debian distribution by Ola
Lundqvist <opal@debian.org>.
PPTP(8)