NAME

       snmptest - communicates with a network entity using SNMP requests

SYNOPSIS

       snmptest [COMMON OPTIONS] AGENT

DESCRIPTION

       snmptest  is  a  flexible  SNMP  application  that can monitor and manage information on a
       network entity.

       After invoking the program, a command line interpreter proceeds to accept commands.   This
       intepreter enables the user to send different types of SNMP requests to target agents.

       AGENT  identifies a target SNMP agent, which is instrumented to monitor the given objects.
       At its simplest, the AGENT specification will consist of a hostname or  an  IPv4  address.
       In  this  situation, the command will attempt communication with the agent, using UDP/IPv4
       to port 161 of the given target host. See snmpcmd(1) for  a  full  list  of  the  possible
       formats for AGENT.

       Once snmptest is invoked, the command line intepreter will prompt with:

       Variable:

       At  this  point you can enter one or more variable names, one per line.  A blank line ends
       the parameter input and will send the request (variables entered) in a single  packet,  to
       the  remote  entity.  Each variable name is given in the format specified in variables(5).
       For example:

       snmptest -c public -v 1 zeus
       Variable: system.sysDescr.0
       Variable:

       will return some information  about  the  request  and  reply  packets,  as  well  as  the
       information:

       requestid 0x5992478A errstat 0x0 errindex 0x0
       system.sysDescr.0 = STRING: "Unix 4.3BSD"

       The  errstatus  value  shows  the error status code for the call.  The possible values for
       errstat are in the header file snmp.h.  The errindex value identifies  the  variable  that
       has  the  given  error.   Index  values  are  assigned to all the variables entered at the
       "Variable": prompt. The first value is assigned an index of 1.

       Upon startup, the program defaults to sending a GET request packet.  The type  of  request
       can be changed by typing one of the following commands at the "Variable:" prompt:

       $G - send a GET request
       $N - send a GETNEXT request
       $S - send a SET request
       $B - send a GETBULK request
            Note: GETBULK is not available in SNMPv1
       $I - send an Inform request
       $T - send an SNMPv2 Trap request

       Other values that can be entered at the "Variable:" prompt are:

       $D - toggle the dumping of each sent and received packet
       $QP - toggle a quicker, less verbose output form
       $Q - Quit the program

       Request Types:

       GET Request:

       When  in  "GET request" mode ($G or default), the user can enter an OID at the "Variable:"
       prompt. The user can enter multiple OIDs, one per prompt. The user enters a blank line  to
       send the GET request.

       GETNEXT Request:

       The "GETNEXT request" mode ($N) is similar to the "Get request" mode, described above.

       SET Request:

       When  in the "SET request" mode ($S), more information is requested by the prompt for each
       variable.  The prompt:

       Type [i|s|x|d|n|o|t|a]:
       requests the type of the variable be entered.  Depending on the type of value you want  to
       set, you can type one of the following:

       i - integer
       u - unsigned integer
       s - octet string in ASCII
       x - octet string in hex bytes, separated by whitespace
       d - octet string as decimal bytes, separated by whitespace
       a - ip address in dotted IP notation
       o - object identifier
       n - null
       t - timeticks
       At this point a value will be prompted for:

       Value:

       If  this  is  an  integer  value,  just type the integer (in decimal).  If it is a decimal
       string, type in white-space separated decimal numbers, one per byte of the string.   Again
       type a blank line at the prompt for the variable name to send the packet.

       GETBULK Request:

       The  "GETBULK  request" mode ($B) is similar to the "Set request" mode.  GETBULK, however,
       is not available in SNMPv1.

       Inform Request:

       The "Inform request" mode ($I) is similar  to  the  "Set  request"  mode.   This  type  of
       request,  however, is not available in SNMPv1. Also, the _agent_ specified on the snmptest
       command should correspond to the target snmptrapd agent.

       SNMPv2 Trap Request:

       The "SNMPv2 Trap Request" mode ($T) is similar to the "Set request" mode.   This  type  of
       request,  however, is not available in SNMPv1. Also, the _agent_ specified on the snmptest
       command should correspond to the target snmptrapd agent.

OPTIONS

       snmptest takes the common options described in the snmpcmd(1) manual page.

EXAMPLES

       The following is an example of sending a GET request for two OIDs:

       % snmptest -v 2c -c public testhost:9999

       Variable: system.sysDescr.0
       Variable: system.sysContact.0
       Variable:
       Received Get Response from 128.2.56.220
       requestid 0x7D9FCD63 errstat 0x0 errindex 0x0
       SNMPv2-MIB::sysDescr.0 = STRING: SunOS testhost 5.9 Generic_112233-02 sun4u
       SNMPv2-MIB::sysContact.0 = STRING: x1111

       The following is an example of sending a GETNEXT request:

       Variable: SNMPv2-MIB::sysORUpTime
       Variable:
       Received Get Response from 128.2.56.220
       requestid 0x7D9FCD64 errstat 0x0 errindex 0x0
       SNMPv2-MIB::sysORUpTime.1 = Timeticks: (6) 0:00:00.06
       Variable:

       The following is an example of sending a SET request:

       Variable: $S
       Request type is Set Request
       Variable: system.sysLocation.0
       Type [i|u|s|x|d|n|o|t|a]: s
       Value: building 17
       Variable:
       Received Get Response from 128.2.56.220
       requestid 0x7D9FCD65 errstat 0x0 errindex 0x0
       SNMPv2-MIB::sysLocation.0 = STRING: building A
       Variable:

       The following is an example of sending a GETBULK request:

       Variable: $B
       Request type is Bulk Request
       Enter a blank line to terminate the list of non-repeaters
       and to begin the repeating variables
       Variable:
       Now input the repeating variables
       Variable: system.sysContact.0
       Variable: system.sysLocation.0
       Variable:
       What repeat count? 2
       Received Get Response from 128.2.56.220
       requestid 0x2EA7942A errstat 0x0 errindex 0x0
       SNMPv2-MIB::sysName.0 = STRING: testhost
       SNMPv2-MIB::sysORLastChange.0 = Timeticks: (58) 0:00:00.58
       SNMPv2-MIB::sysLocation.0 = STRING: bldg A
       SNMPv2-MIB::sysORID.1 = OID: IF-MIB::ifMIB
       Variable:

       The following is an example of sending an Inform request:

       snmptest -v 2c -c public snmptrapd_host
       Variable: $I
       Request type is Inform Request
       (Are you sending to the right port?)
       Variable: system.sysContact.0
       Type [i|u|sIx|d|n|o|t|a]: s
       Value: x12345
       Variable:
       Inform Acknowledged
       Variable:

       The snmptrapd_host will show:

       snmptrapd_host [<ip address>]: Trap SNMPv2-MIB::sysContact.0 = STRING: x12345

       The following is an example of sending an SNMPv2 Trap request:

       snmptest -v 2c -c public snmptrapd_host
       Variable: $T
       Request type is SNMPv2 Trap Request
       (Are you sending to the right port?)
       Variable: system.sysLocation.0
       Type [i|u|s|x|d|n|o|t|a]: s
       Value: building a
       Variable:

       The snmptrapd_host will show:

       snmptrapd_host [<ip address>]: Trap SNMPv2-MIB::sys.0 = STRING:
       building a

SEE ALSO

       snmpcmd(1), snmpget(1), snmpset(1), variables(5)