bionic (4) ale.4freebsd.gz

NAME

     ale — Atheros AR8121/AR8113/AR8114 Gigabit/Fast Ethernet driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

           device miibus
           device ale

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

           if_ale_load="YES"

DESCRIPTION

     The ale device driver provides support for Atheros AR8121 PCI Express Gigabit Ethernet controllers and
     Atheros AR8113/AR8114 PCI Express Fast Ethernet controllers.

     All LOMs supported by the ale driver have TCP/UDP/IP checksum offload for both receive and transmit, TCP
     segmentation offload (TSO), hardware VLAN tag stripping/insertion features, Wake On Lan (WOL) and an
     interrupt coalescing/moderation mechanism as well as a 64-bit multicast hash filter.

     The AR8121 also supports Jumbo Frames (up to 8132 bytes), which can be configured via the interface MTU
     setting.  Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to
     receive and transmit Jumbo Frames.

     The ale driver supports the following media types:

     autoselect   Enable autoselection of the media type and options.  The user can manually override the
                  autoselected mode by adding media options to rc.conf(5).

     10baseT/UTP  Set 10Mbps operation.

     100baseTX    Set 100Mbps (Fast Ethernet) operation.

     1000baseTX   Set 1000baseTX operation over twisted pair.

     The ale driver supports the following media options:

     full-duplex  Force full duplex operation.

     half-duplex  Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

HARDWARE

     The ale device driver provides support for the following Ethernet controllers:

     •   Atheros AR8113 PCI Express Fast Ethernet controller
     •   Atheros AR8114 PCI Express Fast Ethernet controller
     •   Atheros AR8121 PCI Express Gigabit Ethernet controller

LOADER TUNABLES

     Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5).

     hw.ale.msi_disable
             This tunable disables MSI support on the Ethernet hardware.  The default value is 0.

     hw.ale.msix_disable
             This tunable disables MSI-X support on the Ethernet hardware.  The default value is 0.

SYSCTL VARIABLES

     The following variables are available as both sysctl(8) variables and loader(8) tunables:

     dev.ale.%d.int_rx_mod
             Maximum amount of time to delay receive interrupt processing in units of 1us.  The accepted range
             is 0 to 130000, the default is 30(30us).  Value 0 completely disables the interrupt moderation.

     dev.ale.%d.int_tx_mod
             Maximum amount of time to delay transmit interrupt processing in units of 1us.  The accepted range
             is 0 to 130000, the default is 1000(1ms).  Value 0 completely disables the interrupt moderation.

     dev.ale.%d.process_limit
             Maximum amount of Rx frames to be processed in the event loop before rescheduling a taskqueue.  The
             accepted range is 32 to 255, the default value is 128 events.  The interface does not need to be
             brought down and up again before a change takes effect.

SEE ALSO

     altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), vlan(4), ifconfig(8)

HISTORY

     The ale driver was written by Pyun YongHyeon <yongari@FreeBSD.org>.  It first appeared in FreeBSD 7.1.