Provided by: manpages_4.15-1_all 
NAME
lirc - lirc devices
DESCRIPTION
The /dev/lirc* character devices provide a low-level bi-directional interface to infra-red (IR) remotes.
When receiving data, the driver works in two different modes depending on the underlying hardware.
Some hardware (typically TV-cards) decodes the IR signal internally and just provides decoded button
presses as integer values. Drivers for this kind of hardware work in LIRC_MODE_LIRCCODE mode. Such
hardware usually does not support sending IR signals. Furthermore, it usually only works with a specific
remote which is bundled with, for example, a TV-card.
Other hardware provides a stream of pulse/space durations. Such drivers work in LIRC_MODE_MODE2 mode.
Sometimes, this kind of hardware also supports sending IR data. Such hardware can be used with (almost)
any kind of remote.
The LIRC_GET_REC_MODE ioctl (see below) allows probing for the mode.
Reading input with the LIRC_MODE_MODE2 drivers
In the LIRC_MODE_MODE2 mode, the data returned by read(2) provides 32-bit values representing a space or
a pulse duration, by convention typed as lirc_t. The time of the duration (microseconds) is encoded in
the lower 24 bits. The upper 8 bit reflects the type of package:
LIRC_MODE2_SPACE.
Value reflects a space duration (microseconds).
LIRC_MODE2_PULSE.
Value reflects a pulse duration (microseconds).
LIRC_MODE2_FREQUENCY.
Value reflects a frequency (Hz); see the LIRC_SET_MEASURE_CARRIER_MODE ioctl.
LIRC_MODE2_TIMEOUT.
The package reflects a timeout; see the LIRC_SET_REC_TIMEOUT_REPORTS ioctl.
Reading input with the
LIRC_MODE_LIRCCODE drivers
In the LIRC_MODE_LIRCCODE mode, the data returned by read(2) reflects decoded button presses. The length
of each packet can be retrieved using the LIRC_GET_LENGTH ioctl. Reads must be done in blocks matching
the bit count returned by the LIRC_GET_LENGTH ioctl, rounded up so it matches full bytes.
Sending data
When sending data, only the LIRC_MODE_PULSE mode is supported. The data written to the character device
using write(2) is a pulse/space sequence of integer values. Pulses and spaces are only marked implicitly
by their position. The data must start and end with a pulse, thus it must always include an odd number
of samples. The write(2) function blocks until the data has been transmitted by the hardware. If more
data is provided than the hardware can send, the write(2) call fails with the error EINVAL
IOCTL COMMANDS
The complete list of ioctl commands is maintained in the kernel documentation, see SEE ALSO. The ioctl
commands presented here is a subset of the kernel documentation.
The LIRC device's ioctl definition is bound by the ioctl function definition of struct file_operations,
leaving us with an unsigned int for the ioctl command and an unsigned long for the argument. For the
purposes of ioctl portability across 32-bit and 64-bit architectures, these values are capped to their
32-bit sizes.
#include <lirc/include/media/lirc.h> /* But see BUGS */
int ioctl(int fd, int cmd, ...);
The following ioctls can be used to probe or change specific lirc hardware settings. Many require a
third argument, usually an int. referred to below as val.
In general, each driver should have a default set of settings. The driver implementation is expected to
re-apply the default settings when the device is closed by user space, so that every application opening
the device can rely on working with the default settings initially.
Always Supported Commands
/dev/lirc* devices always support the following commands:
LIRC_GET_FEATURES (void)
Returns a bit mask of combined features bits; see FEATURES. Some drivers have dynamic features which
are not updated until after an init() command. If a driver does not announce support of certain
features, calling of the corresponding ioctls is undefined.
LIRC_GET_REC_MODE
Return the receive mode, which will be one of:
LIRC_MODE_MODE2 (void)
The driver returns a sequence of pulse/space durations.
LIRC_MODE_LIRCCODE
The driver returns integer values, each of which represents a decoded button press.
If a device returns an error code for LIRC_GET_REC_MODE, it is safe to assume it is not a lirc device.
Optional Commands
Some lirc devices support commands listed below. Unless otherwise stated, these fail with the error
ENOIOCTLCMD or with the error ENOSYS if the operation isn't supported, or with the error EINVAL if the
operation failed.
LIRC_SET_REC_MODE (int)
Set the receive mode. val is either LIRC_MODE_LIRCCODE or LIRC_MODE_MODE2.
LIRC_GET_LENGTH (void)
Return the length of the returned codes for LIRC_MODE_LIRCCODE-type drivers, otherwise fail with
the error ENOIOCTLCMD.
LIRC_GET_SEND_MODE (void)
Return the send mode. Currently, only LIRC_MODE_PULSE is supported.
LIRC_SET_SEND_MODE (int)
Set the send mode. Currently serves no purpose since only LIRC_MODE_PULSE is supported.
LIRC_GET_SEND_CARRIER (void)
Get the modulation frequency (Hz).
LIRC_SET_SEND_CARRIER (int)
Set the modulation frequency. The argument is the frequency (Hz).
LIRC_GET_SEND_CARRIER (void)
Get the modulation frequency used when decoding (Hz).
SET_SEND_DUTY_CYCLE (int)
Set the carrier duty cycle. val is a number in the range [0,100] which describes the pulse width
as a percentage of the total cycle. Currently, no special meaning is defined for 0 or 100, but
the values are reserved for future use.
LIRC_GET_MIN_TIMEOUT (void), LIRC_GET_MAX_TIMEOUT (void)
Some devices have internal timers that can be used to detect when there's no IR activity for a
long time. This can help lircd(8) in detecting that an IR signal is finished and can speed up the
decoding process. These operations return integer values with the minimum/maximum timeout that
can be set (microseconds). Some devices have a fixed timeout. For such drivers,
LIRC_GET_MIN_TIMEOUT and LIRC_GET_MAX_TIMEOUT will return the same value.
LIRC_SET_REC_TIMEOUT (int)
Set the integer value for IR inactivity timeout (microseconds). To be accepted, the value must be
within the limits defined by LIRC_GET_MIN_TIMEOUT and LIRC_GET_MAX_TIMEOUT. A value of 0 (if
supported by the hardware) disables all hardware timeouts and data should be reported as soon as
possible. If the exact value cannot be set, then the next possible value greater than the given
value should be set.
LIRC_SET_REC_TIMEOUT_REPORTS (int)
Enable (val is 1) or disable (val is 0) timeout packages in LIRC_MODE_MODE2. By default, timeout
reports should be turned off.
LIRC_SET_REC_CARRIER (int)
Set the receive carrier frequency (Hz).
LIRC_SET_REC_CARRIER_RANGE (int)
After opening device, the first use of this operation sets the lower bound of the carrier range,
and the second use sets the upper bound (Hz).
LIRC_SET_MEASURE_CARRIER_MODE (int)
Enable (val is 1) or disable (val is 0) the measure mode. If enabled, from the next key press on,
the driver will send LIRC_MODE2_FREQUENCY packets. By default this should be turned off.
LIRC_GET_REC_RESOLUTION (void)
Return the driver resolution (microseconds).
LIRC_GET_MIN_FILTER_PULSE (void), LIRC_GET_MAX_FILTER_PULSE (void)
Some devices are able to filter out spikes in the incoming signal using given filter rules. These
ioctls return the hardware capabilities that describe the bounds of the possible filters. Filter
settings depend on the IR protocols that are expected. lircd(8) derives the settings from all
protocols definitions found in its lircd.conf(5) config file.
LIRC_GET_MIN_FILTER_SPACE (void), LIRC_GET_MAX_FILTER_SPACE (void)
See LIRC_GET_MIN_FILTER_PULSE.
LIRC_SET_REC_FILTER (int)
Pulses/spaces shorter than this (microseconds) are filtered out by hardware.
LIRC_SET_REC_FILTER_PULSE (int), LIRC_SET_REC_FILTER_SPACE (int)
Pulses/spaces shorter than this (microseconds) are filtered out by hardware. If filters cannot be
set independently for pulse/space, the corresponding ioctls must return an error and
LIRC_SET_REC_FILTER should be used instead.
LIRC_SET_TRANSMITTER_MASK
Enable the set of transmitters specified in val, which contains a bit mask where each enabled
transmitter is a 1. The first transmitter is encoded by the least significant bit, and so on.
When an invalid bit mask is given, for example a bit is set even though the device does not have
so many transmitters, this operation returns the number of available transmitters and does nothing
otherwise.
LIRC_SET_WIDEBAND_RECEIVER (int)
Some devices are equipped with a special wide band receiver which is intended to be used to learn
the output of an existing remote. This ioctl can be used to enable (val equals 1) or disable (val
equals 0) this functionality. This might be useful for devices that otherwise have narrow band
receivers that prevent them to be used with certain remotes. Wide band receivers may also be more
precise. On the other hand its disadvantage usually is reduced range of reception.
Note: wide band receiver may be implicitly enabled if you enable carrier reports. In that case,
it will be disabled as soon as you disable carrier reports. Trying to disable a wide band
receiver while carrier reports are active will do nothing.
LIRC_SETUP_START (void), LIRC_SETUP_END (void)
Setting of several driver parameters can be optimized by bracketing the actual ioctl calls
LIRC_SETUP_START and LIRC_SETUP_END. When a driver receives a LIRC_SETUP_START ioctl, it can
choose to not commit further setting changes to the hardware until a LIRC_SETUP_END is received.
But this is open to the driver implementation and every driver must also handle parameter changes
which are not encapsulated by LIRC_SETUP_START and LIRC_SETUP_END. Drivers can also choose to
ignore these ioctls.
LIRC_NOTIFY_DECODE (void)
This ioctl is called by lircd(8) whenever a successful decoding of an incoming IR signal is
possible. This can be used by supporting hardware to give visual user feedback, for example by
flashing an LED.
FEATURES
The features returned by The LIRC_GET_FEATURES ioctl returns a bit mask describing features of the
driver. The following bits may be returned in the mask:
LIRC_CAN_REC_RAW
The driver is capable of receiving using LIRC_MODE_RAW.
LIRC_CAN_REC_PULSE
The driver is capable of receiving using LIRC_MODE_PULSE.
LIRC_CAN_REC_MODE2
The driver is capable of receiving using LIRC_MODE_MODE2.
LIRC_CAN_REC_LIRCCODE
The driver is capable of receiving using LIRC_MODE_LIRCCODE.
LIRC_CAN_SET_SEND_CARRIER
The driver supports changing the modulation frequency using LIRC_SET_SEND_CARRIER.
LIRC_CAN_SET_SEND_DUTY_CYCLE
The driver supports changing the duty cycle using LIRC_SET_SEND_DUTY_CYCLE.
LIRC_CAN_SET_TRANSMITTER_MASK
The driver supports changing the active transmitter(s) using LIRC_SET_TRANSMITTER_MASK.
LIRC_CAN_SET_REC_CARRIER
The driver supports setting the receive carrier frequency using LIRC_SET_REC_CARRIER.
LIRC_CAN_SET_REC_DUTY_CYCLE_RANGE
The driver supports LIRC_SET_REC_DUTY_CYCLE_RANGE.
LIRC_CAN_SET_REC_CARRIER_RANGE
The driver supports LIRC_SET_REC_CARRIER_RANGE.
LIRC_CAN_GET_REC_RESOLUTION
The driver supports LIRC_GET_REC_RESOLUTION.
LIRC_CAN_SET_REC_TIMEOUT
The driver supports LIRC_SET_REC_TIMEOUT.
LIRC_CAN_SET_REC_FILTER
The driver supports LIRC_SET_REC_FILTER.
LIRC_CAN_MEASURE_CARRIER
The driver supports measuring of the modulation frequency using LIRC_SET_MEASURE_CARRIER_MODE.
LIRC_CAN_USE_WIDEBAND_RECEIVER
The driver supports learning mode using LIRC_SET_WIDEBAND_RECEIVER.
LIRC_CAN_NOTIFY_DECODE
The driver supports LIRC_NOTIFY_DECODE.
LIRC_CAN_SEND_RAW
The driver supports sending using LIRC_MODE_RAW.
LIRC_CAN_SEND_PULSE
The driver supports sending using LIRC_MODE_PULSE.
LIRC_CAN_SEND_MODE2
The driver supports sending using LIRC_MODE_MODE2.
LIRC_CAN_SEND_LIRCCODE
The driver supports sending. (This is uncommon, since LIRCCODE drivers reflect hardware like TV-
cards which usually dos not support sending.)
BUGS
Using these devices requires the kernel source header file lirc.h. This file is not available before
kernel release 4.6. Users of older kernels could use the file bundled in ⟨http://www.lirc.org⟩.
SEE ALSO
lircd(8) https://www.kernel.org/doc/htmldocs/media_api/lirc_dev.html
COLOPHON
This page is part of release 4.15 of the Linux man-pages project. A description of the project,
information about reporting bugs, and the latest version of this page, can be found at
https://www.kernel.org/doc/man-pages/.