Ubuntu Manpage: st - SCSI tape device

NAME

       st - SCSI tape device

SYNOPSIS

       #include <sys/mtio.h>

       int ioctl(int fd, int request [, (void *)arg3]);
       int ioctl(int fd, MTIOCTOP, (struct mtop *)mt_cmd);
       int ioctl(int fd, MTIOCGET, (struct mtget *)mt_status);
       int ioctl(int fd, MTIOCPOS, (struct mtpos *)mt_pos);

DESCRIPTION

The st driver provides the interface to a variety of SCSI tape devices. Currently, the
driver takes control of all detected devices of type “sequential-access”. The st driver
uses major device number 9.

Each device uses eight minor device numbers. The lowermost five bits in the minor numbers
are assigned sequentially in the order of detection. In the 2.6 kernel, the bits above
the eight lowermost bits are concatenated to the five lowermost bits to form the tape
number. The minor numbers can be grouped into two sets of four numbers: the principal
(auto-rewind) minor device numbers, n, and the “no-rewind” device numbers, (n + 128).
Devices opened using the principal device number will be sent a REWIND command when they
are closed. Devices opened using the “no-rewind” device number will not. (Note that
using an auto-rewind device for positioning the tape with, for instance, mt does not lead
to the desired result: the tape is rewound after the mt command and the next command
starts from the beginning of the tape).

Within each group, four minor numbers are available to define devices with different
characteristics (block size, compression, density, etc.) When the system starts up, only
the first device is available. The other three are activated when the default
characteristics are defined (see below). (By changing compile-time constants, it is
possible to change the balance between the maximum number of tape drives and the number of
minor numbers for each drive. The default allocation allows control of 32 tape drives.
For instance, it is possible to control up to 64 tape drives with two minor numbers for
different options.)

Devices are typically created by:

mknod -m 666 /dev/st0 c 9 0
mknod -m 666 /dev/st0l c 9 32
mknod -m 666 /dev/st0m c 9 64
mknod -m 666 /dev/st0a c 9 96
mknod -m 666 /dev/nst0 c 9 128
mknod -m 666 /dev/nst0l c 9 160
mknod -m 666 /dev/nst0m c 9 192
mknod -m 666 /dev/nst0a c 9 224

There is no corresponding block device.

The driver uses an internal buffer that has to be large enough to hold at least one tape
block. In kernels before 2.1.121, the buffer is allocated as one contiguous block. This
limits the block size to the largest contiguous block of memory the kernel allocator can
provide. The limit is currently 128 kB for 32-bit architectures and 256 kB for 64-bit
architectures. In newer kernels the driver allocates the buffer in several parts if
necessary. By default, the maximum number of parts is 16. This means that the maximum
block size is very large (2 MB if allocation of 16 blocks of 128 kB succeeds).

The driver's internal buffer size is determined by a compile-time constant which can be
overridden with a kernel startup option. In addition to this, the driver tries to
allocate a larger temporary buffer at run time if necessary. However, run-time allocation
of large contiguous blocks of memory may fail and it is advisable not to rely too much on
dynamic buffer allocation with kernels older than 2.1.121 (this applies also to demand-
loading the driver with kerneld or kmod).

The driver does not specifically support any tape drive brand or model. After system
start-up the tape device options are defined by the drive firmware. For example, if the
drive firmware selects fixed-block mode, the tape device uses fixed-block mode. The
options can be changed with explicit ioctl(2) calls and remain in effect when the device
is closed and reopened. Setting the options affects both the auto-rewind and the
nonrewind device.

Different options can be specified for the different devices within the subgroup of four.
The options take effect when the device is opened. For example, the system administrator
can define one device that writes in fixed-block mode with a certain block size, and one
which writes in variable-block mode (if the drive supports both modes).

The driver supports tape partitions if they are supported by the drive. (Note that the
tape partitions have nothing to do with disk partitions. A partitioned tape can be seen
as several logical tapes within one medium.) Partition support has to be enabled with an
ioctl(2). The tape location is preserved within each partition across partition changes.
The partition used for subsequent tape operations is selected with an ioctl(2). The
partition switch is executed together with the next tape operation in order to avoid
unnecessary tape movement. The maximum number of partitions on a tape is defined by a
compile-time constant (originally four). The driver contains an ioctl(2) that can format
a tape with either one or two partitions.

Device /dev/tape is usually created as a hard or soft link to the default tape device on
the system.

Starting from kernel 2.6.2, the driver exports in the sysfs directory /sys/class/scsi_tape
the attached devices and some parameters assigned to the devices.

Data transfer
The driver supports operation in both fixed-block mode and variable-block mode (if
supported by the drive). In fixed-block mode the drive writes blocks of the specified
size and the block size is not dependent on the byte counts of the write system calls. In
variable-block mode one tape block is written for each write call and the byte count
determines the size of the corresponding tape block. Note that the blocks on the tape
don't contain any information about the writing mode: when reading, the only important
thing is to use commands that accept the block sizes on the tape.

In variable-block mode the read byte count does not have to match the tape block size
exactly. If the byte count is larger than the next block on tape, the driver returns the
data and the function returns the actual block size. If the block size is larger than the
byte count, an error is returned.

In fixed-block mode the read byte counts can be arbitrary if buffering is enabled, or a
multiple of the tape block size if buffering is disabled. Kernels before 2.1.121 allow
writes with arbitrary byte count if buffering is enabled. In all other cases (kernel
before 2.1.121 with buffering disabled or newer kernel) the write byte count must be a
multiple of the tape block size.

In the 2.6 kernel, the driver tries to use direct transfers between the user buffer and
the device. If this is not possible, the driver's internal buffer is used. The reasons
for not using direct transfers include improper alignment of the user buffer (default is
512 bytes but this can be changed by the HBA driver), one or more pages of the user buffer
not reachable by the SCSI adapter, and so on.

A filemark is automatically written to tape if the last tape operation before close was a
write.

When a filemark is encountered while reading, the following happens. If there are data
remaining in the buffer when the filemark is found, the buffered data is returned. The
next read returns zero bytes. The following read returns data from the next file. The
end of recorded data is signaled by returning zero bytes for two consecutive read calls.
The third read returns an error.

Ioctls
The driver supports three ioctl(2) requests. Requests not recognized by the st driver are
passed to the SCSI driver. The definitions below are from /usr/include/linux/mtio.h:

MTIOCTOP — perform a tape operation
This request takes an argument of type (struct mtop *). Not all drives support all
operations. The driver returns an EIO error if the drive rejects an operation.

/* Structure for MTIOCTOP - mag tape op command: */
struct mtop {
short mt_op; /* operations defined below */
int mt_count; /* how many of them */
};

Magnetic Tape operations for normal tape use:

MTBSF Backward space over mt_count filemarks.

MTBSFM Backward space over mt_count filemarks. Reposition the tape to the EOT side
of the last filemark.

MTBSR Backward space over mt_count records (tape blocks).

MTBSS Backward space over mt_count setmarks.

MTCOMPRESSION Enable compression of tape data within the drive if mt_count is nonzero and
disable compression if mt_count is zero. This command uses the MODE page 15
supported by most DATs.

MTEOM Go to the end of the recorded media (for appending files).

MTERASE Erase tape. With 2.6 kernel, short erase (mark tape empty) is performed if
the argument is zero. Otherwise, long erase (erase all) is done.

MTFSF Forward space over mt_count filemarks.

MTFSFM Forward space over mt_count filemarks. Reposition the tape to the BOT side
of the last filemark.

MTFSR Forward space over mt_count records (tape blocks).

MTFSS Forward space over mt_count setmarks.

MTLOAD Execute the SCSI load command. A special case is available for some HP
autoloaders. If mt_count is the constant MT_ST_HPLOADER_OFFSET plus a
number, the number is sent to the drive to control the autoloader.

MTLOCK Lock the tape drive door.

MTMKPART Format the tape into one or two partitions. If mt_count is positive, it
gives the size of partition 1 and partition 0 contains the rest of the tape.
If mt_count is zero, the tape is formatted into one partition. From kernel
version 4.6, a negative mt_count specifies the size of partition 0 and the
rest of the tape contains partition 1. The physical ordering of partitions
depends on the drive. This command is not allowed for a drive unless the
partition support is enabled for the drive (see MT_ST_CAN_PARTITIONS below).

MTNOP No op—flushes the driver's buffer as a side effect. Should be used before
reading status with MTIOCGET.

MTOFFL Rewind and put the drive off line.

MTRESET Reset drive.

MTRETEN Re-tension tape.

MTREW Rewind.

MTSEEK Seek to the tape block number specified in mt_count. This operation
requires either a SCSI-2 drive that supports the LOCATE command (device-
specific address) or a Tandberg-compatible SCSI-1 drive (Tandberg, Archive
Viper, Wangtek, ...). The block number should be one that was previously
returned by MTIOCPOS if device-specific addresses are used.

MTSETBLK Set the drive's block length to the value specified in mt_count. A block
length of zero sets the drive to variable block size mode.

MTSETDENSITY Set the tape density to the code in mt_count. The density codes supported
by a drive can be found from the drive documentation.

MTSETPART The active partition is switched to mt_count. The partitions are numbered
from zero. This command is not allowed for a drive unless the partition
support is enabled for the drive (see MT_ST_CAN_PARTITIONS below).

MTUNLOAD Execute the SCSI unload command (does not eject the tape).

MTUNLOCK Unlock the tape drive door.

MTWEOF Write mt_count filemarks.

MTWSM Write mt_count setmarks.

Magnetic Tape operations for setting of device options (by the superuser):

MTSETDRVBUFFER
Set various drive and driver options according to bits encoded in mt_count. These
consist of the drive's buffering mode, a set of Boolean driver options, the buffer
write threshold, defaults for the block size and density, and timeouts (only in
kernels 2.1 and later). A single operation can affect only one item in the list
above (the Booleans counted as one item.)

A value having zeros in the high-order 4 bits will be used to set the drive's
buffering mode. The buffering modes are:

0 The drive will not report GOOD status on write commands until the data
blocks are actually written to the medium.

1 The drive may report GOOD status on write commands as soon as all the data
has been transferred to the drive's internal buffer.

2 The drive may report GOOD status on write commands as soon as (a) all the
data has been transferred to the drive's internal buffer, and (b) all
buffered data from different initiators has been successfully written to
the medium.

To control the write threshold the value in mt_count must include the constant
MT_ST_WRITE_THRESHOLD bitwise ORed with a block count in the low 28 bits. The
block count refers to 1024-byte blocks, not the physical block size on the tape.
The threshold cannot exceed the driver's internal buffer size (see DESCRIPTION,
above).

To set and clear the Boolean options the value in mt_count must include one of the
constants MT_ST_BOOLEANS, MT_ST_SETBOOLEANS, MT_ST_CLEARBOOLEANS, or
MT_ST_DEFBOOLEANS bitwise ORed with whatever combination of the following options
is desired. Using MT_ST_BOOLEANS the options can be set to the values defined in
the corresponding bits. With MT_ST_SETBOOLEANS the options can be selectively set
and with MT_ST_DEFBOOLEANS selectively cleared.

The default options for a tape device are set with MT_ST_DEFBOOLEANS. A nonactive
tape device (e.g., device with minor 32 or 160) is activated when the default
options for it are defined the first time. An activated device inherits from the
device activated at start-up the options not set explicitly.

The Boolean options are:

MT_ST_BUFFER_WRITES (Default: true)
Buffer all write operations in fixed-block mode. If this option is false
and the drive uses a fixed block size, then all write operations must be
for a multiple of the block size. This option must be set false to write
reliable multivolume archives.

MT_ST_ASYNC_WRITES (Default: true)
When this option is true, write operations return immediately without
waiting for the data to be transferred to the drive if the data fits into
the driver's buffer. The write threshold determines how full the buffer
must be before a new SCSI write command is issued. Any errors reported by
the drive will be held until the next operation. This option must be set
false to write reliable multivolume archives.

MT_ST_READ_AHEAD (Default: true)
This option causes the driver to provide read buffering and read-ahead in
fixed-block mode. If this option is false and the drive uses a fixed block
size, then all read operations must be for a multiple of the block size.

MT_ST_TWO_FM (Default: false)
This option modifies the driver behavior when a file is closed. The normal
action is to write a single filemark. If the option is true, the driver
will write two filemarks and backspace over the second one.

Note: This option should not be set true for QIC tape drives since they are
unable to overwrite a filemark. These drives detect the end of recorded
data by testing for blank tape rather than two consecutive filemarks. Most
other current drives also detect the end of recorded data and using two
filemarks is usually necessary only when interchanging tapes with some
other systems.

MT_ST_DEBUGGING (Default: false)
This option turns on various debugging messages from the driver (effective
only if the driver was compiled with DEBUG defined nonzero).

MT_ST_FAST_EOM (Default: false)
This option causes the MTEOM operation to be sent directly to the drive,
potentially speeding up the operation but causing the driver to lose track
of the current file number normally returned by the MTIOCGET request. If
MT_ST_FAST_EOM is false, the driver will respond to an MTEOM request by
forward spacing over files.

MT_ST_AUTO_LOCK (Default: false)
When this option is true, the drive door is locked when the device is
opened and unlocked when it is closed.

MT_ST_DEF_WRITES (Default: false)
The tape options (block size, mode, compression, etc.) may change when
changing from one device linked to a drive to another device linked to the
same drive depending on how the devices are defined. This option defines
when the changes are enforced by the driver using SCSI-commands and when
the drives auto-detection capabilities are relied upon. If this option is
false, the driver sends the SCSI-commands immediately when the device is
changed. If the option is true, the SCSI-commands are not sent until a
write is requested. In this case, the drive firmware is allowed to detect
the tape structure when reading and the SCSI-commands are used only to make
sure that a tape is written according to the correct specification.

MT_ST_CAN_BSR (Default: false)
When read-ahead is used, the tape must sometimes be spaced backward to the
correct position when the device is closed and the SCSI command to space
backward over records is used for this purpose. Some older drives can't
process this command reliably and this option can be used to instruct the
driver not to use the command. The end result is that, with read-ahead and
fixed-block mode, the tape may not be correctly positioned within a file
when the device is closed. With 2.6 kernel, the default is true for drives
supporting SCSI-3.

MT_ST_NO_BLKLIMS (Default: false)
Some drives don't accept the READ BLOCK LIMITS SCSI command. If this is
used, the driver does not use the command. The drawback is that the driver
can't check before sending commands if the selected block size is
acceptable to the drive.

MT_ST_CAN_PARTITIONS (Default: false)
This option enables support for several partitions within a tape. The
option applies to all devices linked to a drive.

MT_ST_SCSI2LOGICAL (Default: false)
This option instructs the driver to use the logical block addresses defined
in the SCSI-2 standard when performing the seek and tell operations (both
with MTSEEK and MTIOCPOS commands and when changing tape partition).
Otherwise, the device-specific addresses are used. It is highly advisable
to set this option if the drive supports the logical addresses because they
count also filemarks. There are some drives that support only the logical
block addresses.

MT_ST_SYSV (Default: false)
When this option is enabled, the tape devices use the SystemV semantics.
Otherwise, the BSD semantics are used. The most important difference
between the semantics is what happens when a device used for reading is
closed: in System V semantics the tape is spaced forward past the next
filemark if this has not happened while using the device. In BSD semantics
the tape position is not changed.

MT_NO_WAIT (Default: false)
Enables immediate mode (i.e., don't wait for the command to finish) for
some commands (e.g., rewind).

An example:

struct mtop mt_cmd;
mt_cmd.mt_op = MTSETDRVBUFFER;
mt_cmd.mt_count = MT_ST_BOOLEANS |
MT_ST_BUFFER_WRITES | MT_ST_ASYNC_WRITES;
ioctl(fd, MTIOCTOP, mt_cmd);

The default block size for a device can be set with MT_ST_DEF_BLKSIZE and the
default density code can be set with MT_ST_DEFDENSITY. The values for the
parameters are or'ed with the operation code.

With kernels 2.1.x and later, the timeout values can be set with the subcommand
MT_ST_SET_TIMEOUT ORed with the timeout in seconds. The long timeout (used for
rewinds and other commands that may take a long time) can be set with
MT_ST_SET_LONG_TIMEOUT. The kernel defaults are very long to make sure that a
successful command is not timed out with any drive. Because of this, the driver
may seem stuck even if it is only waiting for the timeout. These commands can be
used to set more practical values for a specific drive. The timeouts set for one
device apply for all devices linked to the same drive.

Starting from kernels 2.4.19 and 2.5.43, the driver supports a status bit which
indicates whether the drive requests cleaning. The method used by the drive to
return cleaning information is set using the MT_ST_SEL_CLN subcommand. If the
value is zero, the cleaning bit is always zero. If the value is one, the
TapeAlert data defined in the SCSI-3 standard is used (not yet implemented).
Values 2–17 are reserved. If the lowest eight bits are >= 18, bits from the
extended sense data are used. The bits 9–16 specify a mask to select the bits to
look at and the bits 17–23 specify the bit pattern to look for. If the bit
pattern is zero, one or more bits under the mask indicate the cleaning request.
If the pattern is nonzero, the pattern must match the masked sense data byte.

MTIOCGET — get status
This request takes an argument of type (struct mtget *).

/* structure for MTIOCGET - mag tape get status command */
struct mtget {
long mt_type;
long mt_resid;
/* the following registers are device dependent */
long mt_dsreg;
long mt_gstat;
long mt_erreg;
/* The next two fields are not always used */
daddr_t mt_fileno;
daddr_t mt_blkno;
};

mt_type The header file defines many values for mt_type, but the current driver reports
only the generic types MT_ISSCSI1 (Generic SCSI-1 tape) and MT_ISSCSI2 (Generic
SCSI-2 tape).

mt_resid contains the current tape partition number.

mt_dsreg reports the drive's current settings for block size (in the low 24 bits) and
density (in the high 8 bits). These fields are defined by MT_ST_BLKSIZE_SHIFT,
MT_ST_BLKSIZE_MASK, MT_ST_DENSITY_SHIFT, and MT_ST_DENSITY_MASK.

mt_gstat reports generic (device independent) status information. The header file
defines macros for testing these status bits:

GMT_EOF(x): The tape is positioned just after a filemark (always false after an
MTSEEK operation).

GMT_BOT(x): The tape is positioned at the beginning of the first file (always
false after an MTSEEK operation).

GMT_EOT(x): A tape operation has reached the physical End Of Tape.

GMT_SM(x): The tape is currently positioned at a setmark (always false after an
MTSEEK operation).

GMT_EOD(x): The tape is positioned at the end of recorded data.

GMT_WR_PROT(x): The drive is write-protected. For some drives this can also
mean that the drive does not support writing on the current medium type.

GMT_ONLINE(x): The last open(2) found the drive with a tape in place and ready
for operation.

GMT_D_6250(x), GMT_D_1600(x), GMT_D_800(x): This “generic” status information
reports the current density setting for 9-track ½" tape drives only.

GMT_DR_OPEN(x): The drive does not have a tape in place.

GMT_IM_REP_EN(x): Immediate report mode. This bit is set if there are no
guarantees that the data has been physically written to the tape when the
write call returns. It is set zero only when the driver does not buffer
data and the drive is set not to buffer data.

GMT_CLN(x): The drive has requested cleaning. Implemented in kernels since
2.4.19 and 2.5.43.

mt_erreg The only field defined in mt_erreg is the recovered error count in the low 16
bits (as defined by MT_ST_SOFTERR_SHIFT and MT_ST_SOFTERR_MASK. Due to
inconsistencies in the way drives report recovered errors, this count is often
not maintained (most drives do not by default report soft errors but this can
be changed with a SCSI MODE SELECT command).

mt_fileno reports the current file number (zero-based). This value is set to -1 when the
file number is unknown (e.g., after MTBSS or MTSEEK).

mt_blkno reports the block number (zero-based) within the current file. This value is
set to -1 when the block number is unknown (e.g., after MTBSF, MTBSS, or
MTSEEK).

MTIOCPOS — get tape position
This request takes an argument of type (struct mtpos *) and reports the drive's notion of
the current tape block number, which is not the same as mt_blkno returned by MTIOCGET.
This drive must be a SCSI-2 drive that supports the READ POSITION command (device-specific
address) or a Tandberg-compatible SCSI-1 drive (Tandberg, Archive Viper, Wangtek, ... ).

/* structure for MTIOCPOS - mag tape get position command */
struct mtpos {
long mt_blkno; /* current block number */
};

RETURN VALUE

       EACCES        An attempt was made to write or erase a write-protected tape.   (This  error
                     is not detected during open(2).)

       EBUSY         The device is already in use or the driver was unable to allocate a buffer.

       EFAULT        The command parameters point to memory not belonging to the calling process.

       EINVAL        An ioctl(2) had an invalid argument, or a requested block size was invalid.

       EIO           The requested operation could not be completed.

       ENOMEM        The  byte  count  in  read(2) is smaller than the next physical block on the
                     tape.  (Before 2.2.18 and 2.4.0-test6 the extra  bytes  have  been  silently
                     ignored.)

       ENOSPC        A  write  operation  could not be completed because the tape reached end-of-
                     medium.

       ENOSYS        Unknown ioctl(2).

       ENXIO         During opening, the tape device does not exist.

       EOVERFLOW     An attempt was made to read or write a variable-length block that is  larger
                     than the driver's internal buffer.

       EROFS         Open  is  attempted  with  O_WRONLY  or O_RDWR when the tape in the drive is
                     write-protected.

FILES

       /dev/st*
              the auto-rewind SCSI tape devices

       /dev/nst*
              the nonrewind SCSI tape devices

NOTES

1. When exchanging data between systems, both systems have to agree on the physical tape
block size. The parameters of a drive after startup are often not the ones most
operating systems use with these devices. Most systems use drives in variable-block
mode if the drive supports that mode. This applies to most modern drives, including
DATs, 8mm helical scan drives, DLTs, etc. It may be advisable to use these drives in
variable-block mode also in Linux (i.e., use MTSETBLK or MTSETDEFBLK at system startup
to set the mode), at least when exchanging data with a foreign system. The drawback
of this is that a fairly large tape block size has to be used to get acceptable data
transfer rates on the SCSI bus.

2. Many programs (e.g., tar(1)) allow the user to specify the blocking factor on the
command line. Note that this determines the physical block size on tape only in
variable-block mode.

3. In order to use SCSI tape drives, the basic SCSI driver, a SCSI-adapter driver and the
SCSI tape driver must be either configured into the kernel or loaded as modules. If
the SCSI-tape driver is not present, the drive is recognized but the tape support
described in this page is not available.

4. The driver writes error messages to the console/log. The SENSE codes written into
some messages are automatically translated to text if verbose SCSI messages are
enabled in kernel configuration.

5. The driver's internal buffering allows good throughput in fixed-block mode also with
small read(2) and write(2) byte counts. With direct transfers this is not possible
and may cause a surprise when moving to the 2.6 kernel. The solution is to tell the
software to use larger transfers (often telling it to use larger blocks). If this is
not possible, direct transfers can be disabled.

COLOPHON

       This  page  is  part of release 4.15 of the Linux man-pages project.  A description of the
       project, information about reporting bugs, and the latest version of  this  page,  can  be
       found at https://www.kernel.org/doc/man-pages/.