Provided by: shorewall_5.1.12.2-1_all 
NAME
masq - Shorewall Masquerade/SNAT definition file
SYNOPSIS
/etc/shorewall[6]/masq
DESCRIPTION
This file is used to define dynamic NAT (Masquerading) and to define Source NAT (SNAT).
While still supported, its use is deprecated in favor of shorewall-snat[1](5) which was
introduced in Shorewall 5.0.14.
Warning
The entries in this file are order-sensitive. The first entry that matches a
particular connection will be the one that is used.
Warning
If you have more than one ISP link, adding entries to this file will not force
connections to go out through a particular link. You must use entries in
shorewall-rtrules[2](5) or PREROUTING entries in shorewall-mangle[3](5) to do that.
The columns in the file are as follows.
INTERFACE:DEST -
{[+]interfacelist[:[digit]][:[dest-address[,dest-address]...[exclusion]]|?COMMENT}
Outgoing interfacelist. This may be a comma-separated list of interface names. This is
usually your internet interface. If ADD_SNAT_ALIASES=Yes in shorewall.conf[4](5), you
may add ":" and a digit to indicate that you want the alias added with that name
(e.g., eth0:0). This will allow the alias to be displayed with ifconfig. That is the
only use for the alias name; it may not appear in any other place in your Shorewall
configuration.
Each interface must match an entry in shorewall-interfaces[5](5). Shorewall allows
loose matches to wildcard entries in shorewall-interfaces[5](5). For example, ppp0 in
this file will match a shorewall-interfaces[5](5) entry that defines ppp+.
Where more that one internet provider share a single interface[6], the provider is
specified by including the provider name or number in parentheses:
eth0(Avvanta)
In that case, you will want to specify the interface's address for that provider in
the ADDRESS column.
The interface may be qualified by adding the character ":" followed by a
comma-separated list of destination host or subnet addresses to indicate that you only
want to change the source IP address for packets being sent to those particular
destinations. Exclusion is allowed (see shorewall-exclusion[7](5)) as are ipset names
preceded by a plus sign '+';
If you wish to inhibit the action of ADD_SNAT_ALIASES for this entry then include the
":" but omit the digit:
eth0(Avvanta):
eth2::192.0.2.32/27
Normally Masq/SNAT rules are evaluated after those for one-to-one NAT (defined in
shorewall-nat[8](5)). If you want the rule to be applied before one-to-one NAT rules,
prefix the interface name with "+":
+eth0
+eth0:192.0.2.32/27
+eth0:2
This feature should only be required if you need to insert rules in this file that
preempt entries in shorewall-nat[8](5).
Comments may be attached to Netfilter rules generated from entries in this file
through the use of ?COMMENT lines. These lines begin with ?COMMENT; the remainder of
the line is treated as a comment which is attached to subsequent rules until another
?COMMENT line is found or until the end of the file is reached. To stop adding
comments to rules, use a line containing only ?COMMENT.
Beginning with Shorewall 4.6.0, a new syntax is also accepted. With the exception of
the leading '+', the interfacelist and qualifiers may appear within the parentheses of
INLINE(...).
Example:
+INLINE(eth0)
When this is done, you may augment the rule generated by Shorewall with iptables
matches of your own. These matches appear after a semicolon (';') at the end of the
line.
See example 8 below.
SOURCE (Formerly called SUBNET - Optional) - [interface|address[,address][exclusion]]
Set of hosts that you wish to masquerade. You can specify this as an address (net or
host) or as an interface (use of an interface is deprecated). If you give the name of
an interface, the interface must be up before you start the firewall and the Shorewall
rules compiler will warn you of that fact. (Shorewall will use your main routing table
to determine the appropriate addresses to masquerade).
The preferred way to specify the SOURCE is to supply one or more host or network
addresses separated by comma. You may use ipset names preceded by a plus sign (+) to
specify a set of hosts.
ADDRESS (Optional) -
[-|NONAT|[address-or-address-range][:lowport-highport][:random][:persistent]|detect|random]
If you specify an address here, SNAT will be used and this will be the source address.
If ADD_SNAT_ALIASES is set to Yes or yes in shorewall.conf[4](5) then Shorewall will
automatically add this address to the INTERFACE named in the first column.
You may also specify a range of up to 256 IP addresses if you want the SNAT address to
be assigned from that range in a round-robin fashion by connection. The range is
specified by first.ip.in.range-last.ip.in.range. You may follow the port range with
:random in which case assignment of ports from the list will be random. random may
also be specified by itself in this column in which case random local port assignments
are made for the outgoing connections.
Example: 206.124.146.177-206.124.146.180
You may follow the port range (or :random) with :persistent. This is only useful when
an address range is specified and causes a client to be given the same
source/destination IP pair. This feature replaces the SAME modifier which was removed
from Shorewall in version 4.4.0. Unlike random, persistent may not be used by itself.
You may also use the special value "detect" which causes Shorewall to determine the IP
addresses configured on the interface named in the INTERFACES column and substitute
them in this column.
Finally, you may also specify a comma-separated list of ranges and/or addresses in
this column.
This column may not contain DNS Names.
Normally, Netfilter will attempt to retain the source port number. You may cause
netfilter to remap the source port by following an address or range (if any) by ":"
and a port range with the format lowport-highport. If this is done, you must specify
"tcp" or "udp" in the PROTO column.
Examples:
192.0.2.4:5000-6000
:4000-5000
If you simply place NONAT in this column, no rewriting of the source IP address or
port number will be performed. This is useful if you want particular traffic to be
exempt from the entries that follow in the file.
If you want to leave this column empty but you need to specify the next column then
place a hyphen ("-") here.
PROTO (Optional) - {-|[!]{protocol-name|protocol-number}[,...]|+ipset}
If you wish to restrict this entry to a particular protocol then enter the protocol
name (from protocols(5)) or number here.
Beginning with Shorewall 4.5.12, this column can accept a comma-separated list of
protocols.
Beginning with Shorewall 4.6.0, an ipset name can be specified in this column. This is
intended to be used with bitmap:port ipsets.
PORT (Optional) - {-|[!]port-name-or-number[,port-name-or-number]...|+ipset}
If the PROTO column specifies TCP (6), UDP (17), DCCP (33), SCTP (132) or UDPLITE
(136) then you may list one or more port numbers (or names from services(5)) or port
ranges separated by commas.
Port ranges are of the form lowport:highport.
Beginning with Shorewall 4.6.0, an ipset name can be specified in this column. This is
intended to be used with bitmap:port ipsets.
IPSEC (Optional) - [option[,option]...]
If you specify a value other than "-" in this column, you must be running kernel 2.6
and your kernel and iptables must include policy match support.
Comma-separated list of options from the following. Only packets that will be
encrypted via an SA that matches these options will have their source address changed.
reqid=number
where number is specified using setkey(8) using the 'unique:number option for the
SPD level.
spi=<number>
where number is the SPI of the SA used to encrypt/decrypt packets.
proto=ah|esp|ipcomp
IPSEC Encapsulation Protocol
mss=number
sets the MSS field in TCP packets
mode=transport|tunnel
IPSEC mode
tunnel-src=address[/mask]
only available with mode=tunnel
tunnel-dst=address[/mask]
only available with mode=tunnel
strict
Means that packets must match all rules.
next
Separates rules; can only be used with strict
yes
When used by itself, causes all traffic that will be encrypted/encapsulated to
match the rule.
MARK - [!]value[/mask][:C]
Defines a test on the existing packet or connection mark. The rule will match only if
the test returns true.
If you don't want to define a test but need to specify anything in the following
columns, place a "-" in this field.
!
Inverts the test (not equal)
value
Value of the packet or connection mark.
mask
A mask to be applied to the mark before testing.
:C
Designates a connection mark. If omitted, the packet mark's value is tested.
USER (Optional) - [!][user-name-or-number][:group-name-or-number][+program-name]
This column was formerly labelled USER/GROUP.
Only locally-generated connections will match if this column is non-empty.
When this column is non-empty, the rule matches only if the program generating the
output is running under the effective user and/or group specified (or is NOT running
under that id if "!" is given).
Examples:
joe
program must be run by joe
:kids
program must be run by a member of the 'kids' group
!:kids
program must not be run by a member of the 'kids' group
+upnpd
#program named upnpd
Important
The ability to specify a program name was removed from Netfilter in kernel
version 2.6.14.
SWITCH - [!]switch-name[={0|1}]
Added in Shorewall 4.5.1 and allows enabling and disabling the rule without requiring
shorewall restart.
The rule is enabled if the value stored in /proc/net/nf_condition/switch-name is 1.
The rule is disabled if that file contains 0 (the default). If '!' is supplied, the
test is inverted such that the rule is enabled if the file contains 0.
Within the switch-name, '@0' and '@{0}' are replaced by the name of the chain to which
the rule is a added. The switch-name (after '@...' expansion) must begin with a letter
and be composed of letters, decimal digits, underscores or hyphens. Switch names must
be 30 characters or less in length.
Switches are normally off. To turn a switch on:
echo 1 >
/proc/net/nf_condition/switch-name
To turn it off again:
echo 0 >
/proc/net/nf_condition/switch-name
Switch settings are retained over shorewall restart.
Beginning with Shorewall 4.5.10, when the switch-name is followed by =0 or =1, then
the switch is initialized to off or on respectively by the start command. Other
commands do not affect the switch setting.
ORIGDEST - [-|address[,address]...[exclusion]|exclusion]
(Optional) Added in Shorewall 4.5.6. This column may be included and may contain one
or more addresses (host or network) separated by commas. Address ranges are not
allowed. When this column is supplied, rules are generated that require that the
original destination address matches one of the listed addresses. It is useful for
specifying that SNAT should occur only for connections that were acted on by a DNAT
when they entered the firewall.
This column was formerly labelled ORIGINAL DEST.
PROBABILITY - [probability]
Added in Shorewall 5.0.0. When non-empty, requires the Statistics Match capability in
your kernel and ip6tables and causes the rule to match randomly but with the given
probability. The probability is a number 0 < probability <= 1 and may be expressed at
up to 8 decimal points of precision.
EXAMPLES
IPv4 Example 1:
You have a simple masquerading setup where eth0 connects to a DSL or cable modem and
eth1 connects to your local network with subnet 192.168.0.0/24.
Your entry in the file will be:
#INTERFACE SOURCE
eth0 192.168.0.0/24
IPv4 Example 2:
You add a router to your local network to connect subnet 192.168.1.0/24 which you also
want to masquerade. You then add a second entry for eth0 to this file:
#INTERFACE SOURCE
eth0 192.168.1.0/24
IPv4 Example 3:
You have an IPSEC tunnel through ipsec0 and you want to masquerade packets coming from
192.168.1.0/24 but only if these packets are destined for hosts in 10.1.1.0/24:
#INTERFACE SOURCE
ipsec0:10.1.1.0/24 196.168.1.0/24
IPv4 Example 4:
You want all outgoing traffic from 192.168.1.0/24 through eth0 to use source address
206.124.146.176 which is NOT the primary address of eth0. You want 206.124.146.176 to
be added to eth0 with name eth0:0.
#INTERFACE SOURCE ADDRESS
eth0:0 192.168.1.0/24 206.124.146.176
IPv4 Example 5:
You want all outgoing SMTP traffic entering the firewall from 172.20.1.0/29 to be sent
from eth0 with source IP address 206.124.146.177. You want all other outgoing traffic
from 172.20.1.0/29 to be sent from eth0 with source IP address 206.124.146.176.
#INTERFACE SOURCE ADDRESS PROTO DPORT
eth0 172.20.1.0/29 206.124.146.177 tcp smtp
eth0 172.20.1.0/29 206.124.146.176
Warning
The order of the above two rules is significant!
IPv4 Example 6:
Connections leaving on eth0 and destined to any host defined in the ipset myset should
have the source IP address changed to 206.124.146.177.
#INTERFACE SOURCE ADDRESS
eth0:+myset[dst] - 206.124.146.177
IPv4 Example 7:
SNAT outgoing connections on eth0 from 192.168.1.0/24 in round-robin fashion between
addresses 1.1.1.1, 1.1.1.3, and 1.1.1.9 (Shorewall 4.5.9 and later).
/etc/shorewall/tcrules:
#ACTION SOURCE DEST PROTO DPORT SPORT USER TEST
1-3:CF 192.168.1.0/24 eth0 ; state=NEW
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS ...
eth0 192.168.1.0/24 1.1.1.1 ; mark=1:C
eth0 192.168.1.0/24 1.1.1.3 ; mark=2:C
eth0 192.168.1.0/24 1.1.1.9 ; mark=3:C
IPv4 Example 8:
Your eth1 has two public IP addresses: 70.90.191.121 and 70.90.191.123. You want to
use the iptables statistics match to masquerade outgoing connections evenly between
these two addresses.
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS
INLINE(eth1) 0.0.0.0/0 70.90.191.121 ; -m statistic --mode random --probability 0.50
eth1 0.0.0.0/0 70.90.191.123
If INLINE_MATCHES=Yes in shorewall.conf(5)[4], then these rules may be specified as
follows:
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS
eth1 0.0.0.0/0 70.90.191.121 ; -m statistic --mode random --probability 0.50
eth1 0.0.0.0/0 70.90.191.123
IPv6 Example 1:
You have a simple 'masquerading' setup where eth0 connects to a DSL or cable modem and
eth1 connects to your local network with subnet 2001:470:b:787::0/64
Your entry in the file will be:
#INTERFACE SOURCE ADDRESS
eth0 2001:470:b:787::0/64 -
IPv6 Example 2:
Your sit1 interface has two public IP addresses: 2001:470:a:227::1 and
2001:470:b:227::1. You want to use the iptables statistics match to masquerade
outgoing connections evenly between these two addresses.
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS
INLINE(sit1) ::/0 2001:470:a:227::1 ; -m statistic --mode random --probability 0.50
sit1 ::/0 2001:470:a:227::2
If INLINE_MATCHES=Yes in shorewall6.conf[9](5), then these rules may be specified as
follows:
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS
sit1 ::/0 2001:470:a:227::1 ; -m statistic --mode random --probability 0.50
sit1 ::/0 2001:470:a:227::2
FILES
/etc/shorewall/masq
/etc/shorewall6/masq
SEE ALSO
http://www.shorewall.net/configuration_file_basics.htm#Pairs[10]
shorewall(8)
NOTES
1. shorewall-snat
http://www.shorewall.netshorewall-snat.html
2. shorewall-rtrules
http://www.shorewall.net/manpages/shorewall-rtrules.html
3. shorewall-mangle
http://www.shorewall.net/manpages/shorewall-mangle.html
4. shorewall.conf
http://www.shorewall.net/manpages/shorewall.conf.html
5. shorewall-interfaces
http://www.shorewall.net/manpages/shorewall-interfaces.html
6. more that one internet provider share a single interface
http://www.shorewall.net/4.4/MultiISP.html#Shared
7. shorewall-exclusion
http://www.shorewall.net/manpages/shorewall-exclusion.html
8. shorewall-nat
http://www.shorewall.net/manpages/shorewall-nat.html
9. shorewall6.conf
http://www.shorewall.net/manpages6/shorewall6.conf.html
10. http://www.shorewall.net/configuration_file_basics.htm#Pairs
http://www.shorewall.net/configuration_file_basics.htm#Pairs