Ubuntu Manpage: tunnels - Shorewall VPN definition file

NAME

       tunnels - Shorewall VPN definition file

SYNOPSIS

       /etc/shorewall[6]/tunnels

DESCRIPTION

       The tunnels file is used to define rules for encapsulated (usually encrypted) traffic to
       pass between the Shorewall system and a remote gateway. Traffic flowing through the tunnel
       is handled using the normal zone/policy/rule mechanism. See
       http://www.shorewall.net/VPNBasics.html[1] for details.

       The columns in the file are as follows.

       TYPE -
       {ipsec[:{noah|ah}]|ipsecnat|ipip|gre|l2tp|pptpclient|pptpserver|?COMMENT|{openvpn|openvpnclient|openvpnserver}[:{tcp|udp}][:port]|generic:protocol[:port]}
           Types are as follows:

                       6to4 or 6in4  - 6to4 or 6in4 tunnel. The 6in4 synonym was added in 4.4.24.
                       ipsec         - IPv4 IPSEC
                       ipsecnat      - IPv4 IPSEC with NAT Traversal (UDP port 4500 encapsulation)
                       ipip          - IPv4 encapsulated in IPv4 (Protocol 4)
                       gre           - Generalized Routing Encapsulation (Protocol 47)
                       l2tp          - Layer 2 Tunneling Protocol (UDP port 1701)
                       pptpclient    - PPTP Client runs on the firewall
                       pptpserver    - PPTP Server runs on the firewall
                       openvpn       - OpenVPN in point-to-point mode
                       openvpnclient - OpenVPN client runs on the firewall
                       openvpnserver - OpenVPN server runs on the firewall
                       generic       - Other tunnel type
                       tinc          - TINC (added in Shorewall 4.6.6)

           If the type is ipsec, it may be followed by :ah to indicate that the Authentication
           Headers protocol (51) is used by the tunnel (the default is :noah which means that
           protocol 51 is not used). NAT traversal is only supported with ESP (protocol 50) so
           ipsecnat tunnels don't allow the ah option (ipsecnat:noah may be specified but is
           redundant).

           If type is openvpn, openvpnclient or openvpnserver it may optionally be followed by
           ":" and tcp or udp to specify the protocol to be used. If not specified, udp is
           assumed.

           If type is openvpn, openvpnclient or openvpnserver it may optionally be followed by
           ":" and the port number used by the tunnel. if no ":" and port number are included,
           then the default port of 1194 will be used. . Where both the protocol and port are
           specified, the protocol must be given first (e.g., openvpn:tcp:4444).

           If type is generic, it must be followed by ":" and a protocol name (from
           /etc/protocols) or a protocol number. If the protocol is tcp or udp (6 or 17), then it
           may optionally be followed by ":" and a port number.

           Comments may be attached to Netfilter rules generated from entries in this file
           through the use of /COMMENT lines. These lines begin with ?COMMENT; the remainder of
           the line is treated as a comment which is attached to subsequent rules until another
           ?COMMENT line is found or until the end of the file is reached. To stop adding
           comments to rules, use a line containing only ?COMMENT.

               Note
               Beginning with Shorewall 4.5.11, ?COMMENT is a synonym for COMMENT and is
               preferred.

       ZONE - zone
           The zone of the physical interface through which tunnel traffic passes. This is
           normally your internet zone.

       GATEWAY(S) (gateway or gateways) - address-or-range [ , ... ]
           The IP address of the remote tunnel gateway. If the remote gateway has no fixed
           address (Road Warrior) then specify the gateway as 0.0.0.0/0. May be specified as a
           network address and if your kernel and iptables include iprange match support then IP
           address ranges are also allowed.

           Beginning with Shorewall 4.5.3, a list of addresses or ranges may be given. Exclusion
           (shorewall-exclusion[2] (5) ) is not supported.

       GATEWAY ZONES (gateway_zone or gateway_zones) - [zone[,zone]...]
           Optional. If the gateway system specified in the third column is a standalone host
           then this column should contain a comma-separated list of the names of the zones that
           the host might be in. This column only applies to IPSEC tunnels where it enables
           ISAKMP traffic to flow through the tunnel to the remote gateway(s).

EXAMPLE

IPv4 Example 1:
IPSec tunnel.

The remote gateway is 4.33.99.124 and the remote subnet is 192.168.9.0/24. The tunnel
does not use the AH protocol

#TYPE ZONE GATEWAY
ipsec:noah net 4.33.99.124

IPv4 Example 2:
Road Warrior (LapTop that may connect from anywhere) where the "gw" zone is used to
represent the remote LapTop

#TYPE ZONE GATEWAY GATEWAY ZONES
ipsec net 0.0.0.0/0 gw

IPv4 Example 3:
Host 4.33.99.124 is a standalone system connected via an ipsec tunnel to the firewall
system. The host is in zone gw.

#TYPE ZONE GATEWAY GATEWAY ZONES
ipsec net 4.33.99.124 gw

IPv4 Example 4:
Road Warriors that may belong to zones vpn1, vpn2 or vpn3. The FreeS/Wan _updown
script will add the host to the appropriate zone using the shorewall add command on
connect and will remove the host from the zone at disconnect time.

#TYPE ZONE GATEWAY GATEWAY ZONES
ipsec net 0.0.0.0/0 vpn1,vpn2,vpn3

IPv4 Example 5:
You run the Linux PPTP client on your firewall and connect to server 192.0.2.221.

#TYPE ZONE GATEWAY GATEWAY ZONES
pptpclient net 192.0.2.221

IPv4 Example 6:
You run a PPTP server on your firewall.

#TYPE ZONE GATEWAY GATEWAY ZONES
pptpserver net 0.0.0.0/0

Example 7:
OPENVPN tunnel. The remote gateway is 4.33.99.124 and openvpn uses port 7777.

#TYPE ZONE GATEWAY GATEWAY ZONES
openvpn:7777 net 4.33.99.124

IPv4 Example 8:
You have a tunnel that is not one of the supported types. Your tunnel uses UDP port
4444. The other end of the tunnel is 4.3.99.124.

#TYPE ZONE GATEWAY GATEWAY ZONES
generic:udp:4444 net 4.3.99.124

IPv4 Example 9:
TINC tunnel where the remote gateways are not specified. If you wish to specify a list
of gateways, you can do so in the GATEWAY column.

#TYPE ZONE GATEWAY GATEWAY ZONES
tinc net 0.0.0.0/0

IPv6 Example 1:
IPSec tunnel.

The remote gateway is 2001:cec792b4:1::44. The tunnel does not use the AH protocol

#TYPE ZONE GATEWAY
ipsec:noah net 2002:cec792b4:1::44

IPv6 Example 2:
Road Warrior (LapTop that may connect from anywhere) where the "gw" zone is used to
represent the remote LapTop

#TYPE ZONE GATEWAY GATEWAY ZONES
ipsec net ::/0 gw

IPv6 Example 3:
Host 2001:cec792b4:1::44 is a standalone system connected via an ipsec tunnel to the
firewall system. The host is in zone gw.

#TYPE ZONE GATEWAY GATEWAY ZONES
ipsec net 2001:cec792b4:1::44 gw

IPv6 Example 4:
OPENVPN tunnel. The remote gateway is 2001:cec792b4:1::44 and openvpn uses port 7777.

#TYPE ZONE GATEWAY GATEWAY ZONES
openvpn:7777 net 2001:cec792b4:1::44

IPv6 Example 8:
You have a tunnel that is not one of the supported types. Your tunnel uses UDP port
4444. The other end of the tunnel is 2001:cec792b4:1::44.

#TYPE ZONE GATEWAY GATEWAY ZONES
generic:udp:4444 net 2001:cec792b4:1::44

IPv6 Example 9:
TINC tunnel where the remote gateways are not specified. If you wish to specify a list
of gateways, you can do so in the GATEWAY column.

#TYPE ZONE GATEWAY GATEWAY ZONES
tinc net ::/0

FILES

       /etc/shorewall/tunnels

       /etc/shorewall6/tunnels

NOTES