Ubuntu Manpage: amanda-devices - Configuring and Using Amanda Devices

Provided by: amanda-common_3.5.1-1ubuntu0.3_amd64

NAME

       amanda-devices - Configuring and Using Amanda Devices

DESCRIPTION

       The Device API specifies a generic interface between Amanda and storage devices such as
       tapes or disks. This manual page describes the device drivers included with Amanda.

       This is a user-level description of the API, and does not address details that are only of
       concern to developers. For that purpose, consult the Amanda source code and
       http://wiki.zmanda.com.

       The term "device driver" describes the software that can communicate with some kind of
       backend storage, e.g., a tape driver. A "device" is the storage element itself, usually a
       piece of hardware. When discussing a device and its driver as a unit, the term "device" is
       sometimes also used to refer to the combination of device and driver.

SPECIFYING DEVICES

Device names take the form TYPE:NODE, where TYPE selects a device driver, and NODE
provides further information to that driver. The syntax for each device driver is given in
the corresponding section below.

Devices can be described in amanda.conf(5) with "device" sections, e.g.,

define device top_drive {
tapedev "tape:/dev/nst0"
device-property "BLOCK_SIZE" "131072"
}
Such a device defininition creates a device "alias", in this case named top_drive, which
can then be named in the global tapedev or tpchanger parameter:

tapedev "top_drive"

The global tapedev parameter can also specify a literal device name. For example,

tapedev "file:/amdisks"
is equivalent to

tapedev "default"
define device default {
tapedev "file:/amdisks"
}
Note that, in both cases, the specified devices are actually accessed through the
chg-single changer driver; see amanda-changers(7) for more information.

Device properties specified outside of any device definition apply to all devices. This
syntax is provided mainly for backward compatibility, and for simple Amanda
configurations. Note that there is no way to provide properties specific to a device
without defining a device alias.

See amanda-changers(7) for details on how devices are configured, and in particular on how
device properties are specified. See amanda.conf(5) for more information on Amanda
configuration in general.

Note
There is no way to reset a device property to its default value.

PROPERTIES

Device drivers use properties as a generic means to interact with other parts of Amanda.
Some properties are set by the device driver and used by Amanda to determine how its
devices should be used. Other properties can be set by Amanda or by the user to influence
the driver's behavior. Properties are set for a particular device, so that if you have two
tape devices, they will not share property values.

Properties are specified in amanda.conf with the device-property parameter. The syntax
looks like this:

device-property "FROBNICATOR_PATH" "/var/frobd/state"
device-property "BYTES_PER_FORTNIGHT" "128k"
device-property "USE_QUBITS" "no"

Both the property name and the property value are always quoted. Property names, like
Amanda configuration parameters, are not case-sensitive, and - (dash) and _ (underscore)
may be used interchangeably. String values are given as simple strings, like
FROBNICATOR_PATH in the example above. Integer values can be specified with any of the
suffixes given in the "VALUE SUFFIXES" section of amanda.conf(5), like
BYTES_PER_FORTNIGHT, above. Boolean values can be specified using the same names as in
amanda.conf(5), like USE_QUBITS, above. Some properties have special formats, as described
below.

Some properties are set based on other configuration values, such as tapetype parameters.
These special cases are detailed under the appropriate property, below.

The order in which device properties are set is as follows:

1. Tapetype parameters (including length, blocksize, and readblocksize) are translated
into device properties and set accordingly.

2. Device properties from any device-property configuration parameters are set, in the
order they appear in the configuration file.

Properties described as read-only are not accessible to users. They are listed here for
completeness.

COMMON PROPERTIES
Note that some of these properties are currently unused, and present only for future
expansion. Not all devices implement all of these properties.

APPENDABLE

(read-only) This boolean property indicates whether this device supports appending
data to volumes.

BLOCK_SIZE

(read-write) This property gives the block size, in bytes, that will be used to write
to the device. The usual suffixes ("kbytes", etc.) are allowed. The tapetype
parameter blocksize sets this property.

CANONICAL_NAME

(read-only) This property contains the full canonical name for this device. This
name may not be the same as the user-supplied name, but is a valid name by which to
access this device.

COMMENT

(read-write) This string property is entirely for the user's convenience. It is
supported by all devices, but no device interprets its value in any way.

COMPRESSION

(read-write) This boolean property represents the compression status of the device,
and can be used to enable and disable such compression. This applies mostly to tape
devices, although many tape devices do not support setting compression from software.

COMPRESSION_RATE

(read-only) This property gives the compression rate, as a decimal ratio. It may be
a measured value over some unspecified period or a simple estimate.

CONCURRENCY

(read-only) This property indicates the level of concurrent access that this device
supports.

FULL_DELETION

(read-only) This property indicates whether the device supports erasing the entire
volume. Aside from S3 and VFS, most devices cannot support this feature.

LEOM

(read-write) If this property is true, then the device can detect an EOM condition
before actually running out of space, allowing Amanda to forgo caching parts while
writing. For some devices, it is necessary to override the conservative default value
of this property.

MAX_BLOCK_SIZE

(read-only) This property gives the maximum block size this device can support. See
BLOCK SIZES, below.

MEDIUM_ACCESS_TYPE

(read-only) This property gives the type of the media in the device: read only, WORM
(Write Once, Read Many), read/write, or write only. Write-only devices do not support
recovery, but the data are not necessarily thrown out.

MIN_BLOCK_SIZE

(read-write) This property gives the minimum block size this device can support. See
BLOCK SIZES, below.

MAX_VOLUME_USAGE

(read-write) On devices that support it, this property will limit the total amount of
data written to a volume; attempts to write beyond this point will cause the device to
simulate "out of space." Zero means no limit. The tapetype parameter length sets
this property.

ENFORCE_MAX_VOLUME_USAGE

(read-write) If this property is false, limit set by MAX_VOLUME_USAGE property (and
thus the tapetype LENGTH parameter) will not be verified while writing to device,
allowing the volume to expand without limit. If this property is true, then
MAX_VOLUME_USAGE willbe enforced, limiting the total size of the volume. This property
is not available on all devices; see below.

PARTIAL_DELETION

(read-only) This property indicates whether the device supports deletion of specific
files. Aside from linear tapes and S3, most devices can support this feature. It is
currently unused by Amanda.

STREAMING

(read-only) This property gives the streaming requirement for this device. For
example, tape drives often require a steady supply of data to avoid shoe-shining,
while disk devices have no such requirement. Streaming is accomplished by buffering
device-output-buffer-size bytes of data. The allowed values are "none" (no streaming
buffer necessary), "required" (fill the buffer before starting to write), or "desired"
(fill the buffer before starting to write, and if the buffer becomes empty, stop
writing until it is completely full again).

VERBOSE

(read-write) If this boolean property is set, then the device will produce verbose
debugging output. This property is not recognized by most devices.

BLOCK SIZES
Amanda writes device data in blocks. On most devices the block boundaries are embedded in
the media along with the data itself, so subsequent reads must use the same block sizes.
On tape devices, the block size is dictated by the capabilities of the hardware -- buffer
sizes, physical format, and so on.

Amanda has historically supported a single, fixed block size -- usually 32k. The Device
API adds the ability to specify a block size at runtime, using the BLOCK_SIZE property.
Devices provide MIN_BLOCK_SIZE and MAX_BLOCK_SIZE as a guide to the range of acceptable
block sizes. Note that this does not imply that all sizes in the range MIN_BLOCK_SIZE -
MAX_BLOCK_SIZE are available -- the device may require that block sizes are even multiples
of some power of two, for example. Consult the documentation for your hardware and
operating system for more information.

Most devices are flexible enough to read a volume using a different block size than that
with which it was written. This can be useful when handling old volumes written with a
smaller blocksize, or volumes of unknown blocksize. Unfortunately, some tape devices do
not detect oversized blocks correctly, and may lose data if the configured block size is
smaller than the volume's block size. The tape device driver has a READ_BLOCK_SIZE
property which specifies the minimum buffer size that will be allocated for reads from
tape. If the hardware supports it, setting this property allows Amanda to correctly read
from tapes written with any blocksize less than or equal to READ_BLOCK_SIZE.

Note
The RAIT device does not support flexible block sizes, as its parity algorithm
requires that all child devices have the same, fixed block size.

LEOM DETECTION
Some Amanda devices can detect end-of-medium (running out of space on the device) before
it occurs. This early warning is referred to as logical EOM, and where it is supported
Amanda can operate more efficiently, since the possibility for data loss is reduced.

The boolean LEOM property indicates whether or not a particular device supports LEOM
detection. The sections below also describe the degree of support.

DEVICES

This section lists the device drivers included with Amanda, and basic instructions for
using them. For complete How-To information, consult the Amanda wiki at
http://wiki.zmanda.com.

Null Device
tapedev "null:"

The null device driver only supports writing, and discards all data. It is generally only
useful for testing purposes.

RAIT Device
tapedev "rait:tape:/dev/rmt/tps0d{4,5,6}n"

The RAIT device driver mirrors or stripes data over multiple "child" devices. The child
devices are specified using a shell-like syntax, where alternatives are enclosed in braces
and separated by commas. Braces and commas can be escaped with a backslash. Note that the
backslash itself must be escaped in most contexts. For example:

tapedev "rait:{file:/var/amanda/vtapes,tape:/dev/nst0}"
tapedev "rait:{comma-dev:foo\\,bar,brace-dev:foo\\}bar}" # quoting
If the braces contain a numeric range separated with two dots, that range will be filled
in sequentially. If the first number has a leading zero, then the results will be
zero-padded to the maximum length. For example:

tapedev "rait:file:/var/amanda/vtapes/drive{01..04}"

With two child devices, the RAIT device driver mirrors data such that the two devices
contain identical data and can be used singly for recovery. With more than two devices,
the RAIT device "stripes" data across all but one device and writes a parity block to the
final device, usable for data recovery in the event of a device or volume failure. The
RAIT device scales its blocksize as necessary to match the number of children that will be
used to store data.

When a child device is known to have failed, the RAIT device should be reconfigured to
replace that device with the text "ERROR", e.g.,

tapedev "rait:{tape:/dev/st0,ERROR,tape:/dev/st2}"
This will cause the RAIT device to start up in degraded mode, reconstructing the data from
the missing device.

Like ordinary RAID drivers, the RAIT device driver can automatically enter degraded mode
when one of its child devices fails. However, the RAIT device cannot automatically recover
from any write error nor write any data in degraded mode. When reading, certain errors may
be fatal (rather than causing degraded mode). And in any case, labels on all volumes must
initially match (labeled or otherwise). If you have lost one volume from a set, explicitly
start the device in degraded mode as described above.

This device can detect LEOM if and only if all of the child devices can detect LEOM.

Child Device Block Sizes
The RAIT device driver requires that all of its child devices use the same block size. If
no block sizes are specified, the driver selects the block size closest to 32k that is
within the MIN_BLOCK_SIZE - MAX_BLOCK_SIZE range of all child devices, and calculates its
own blocksize according to the formula rait_blocksize = child_blocksize * (num_children -
1). If a block size is specified for the RAIT device, then it calculates its child block
sizes according to the formula child_blocksize = rait_blocksize / (num_children - 1).
Either way, it sets the BLOCK_SIZE property of each child device accordingly.

S3 Device
tapedev "s3:foocorp-backups/DailySet1-"
device-property "S3_ACCESS_KEY" "MYACCESSKEY"
device-property "S3_SECRET_KEY" "MYSECRETKEY"

The S3 device driver uploads data to the Amazon S3 "storage cloud". Its device name is a
slash-sparated combination of bucket name and prefix: "s3:BUCKET/PREFIX". Since buckets
must be unique across all Amazon S3 users, and since the number of buckets allowed to each
user is limited, the driver can store multiple Amanda volumes in a single S3 bucket,
distinguished by prefix. The prefix and slash can be omitted if they are not needed:
"s3:BUCKET".

The access and secret keys used to authenticate to Amazon S3 are provided as properties.

The S3 device driver stores each block in a distinct S3 object. Due to high HTTP overhead
for each request, use of larger than normal block sizes (> 1 megabyte) is recommended with
the S3 device.

Amanda automatically creates a bucket when writing, if the bucket doesn't already exist.
At that time, it specifies where Amazon should store the data based on the
S3_BUCKET_LOCATION property. If this property is not set, Amazon's default value
(equivalent to "*") is used. The bucket location has both billing and legal concerns, so
you are encouraged to consult Amazon's documentation for details.

Amazon does not permit changes to bucket locations, so this is a permanent specification.
If the bucket already exists and the property is set, then Amanda checks the property
against the location of the bucket, and produces an error if they do not match.

Note
If a location constraint is set, the bucket name must consist only of lower-case
letters, numbers, dashes, and dots.

This driver supports the VERBOSE property, but use it carefully -- it produces a great
deal of output, and may cause spurious failures by filling your debug log partition. Its
logging is generally only useful for developers chasing down a problem in communications
with Amazon's servers.

Since Amazon storage is unlimited, the device never encounteres EOM, so LEOM detection is
trivially enabled for this device.

This driver supports the ENFORCE_MAX_VOLUME_USAGE property. Default value is false. See
COMMON_PROPERTIES, above.

Device-Specific Properties
In addition to the common properties, the S3 device supports the properties listed in this
section.

Most Amanda devices work just fine without any properties, but not the S3 device. A
typical S3 configuration will have an access key and secret key specified:

device-property "S3_ACCESS_KEY" "27D3B8C6C4E7AA423C2B37C72A0D22C8"
device-property "S3_SECRET_KEY" "agphc2Q7Zmxragphc2RmO2xragpzZGY7a2xqCgr"

CHUNKED

(read-write) Default: No. Set to yes if the server support chunked transfer-encoding.
Amazon do not support it, google support it.

CLIENT_ID

(read-write) The client_id for oauth2.

CLIENT_SECRET

(read-write) The client_secret for oauth2.

CREATE-BUCKET

(read-write) Default: yes. If amanda create/delete the bucket.

REFRESH_TOKEN

(read-write) The refresh-token for oauth2.

MAX_RECV_SPEED

(read-write) Maximum speed, in bytes per second, that this device will receive data
from S3. If the average speed exceeds this value, the device will stop reading long
enough to bring the average below this value. Minimum value is 5120.

MAX_SEND_SPEED

(read-write) Maximum speed, in bytes per second, that this device will send data to
S3. If the average speed exceeds this value, the device will stop writing long enough
to bring the average below this value. Minimum value is 5120.

NB_THREADS_BACKUP

(read-write) The number of thread that send data to the s3 device, higher value can
provide more throutput.

NB_THREADS_RECOVERY

(read-write) The number of thread that read data from the s3 device, higher value can
provide more throutput.

OPENSTACK_SWIFT_API

(read-write) Deprecated, set "STORAGE_API to "SWIFT-1.0".

PROXY

(read-write) The proxy hostname or IP in the format "host[:port]".

PASSWORD

(read-write) The password (for swift v2 and v3).

PROJECT-ID

(read-write) The projectid (for google).

READ-FROM-GLACIER

(read-write) Default: NO. Set it to "YES" if some files are transitioned to glacier.

REUSE-CONNECTION

(read-write) Default: YES. Set it to "NO" if reusing a connection cause some bug, this
is sometime the case with big block size.

S3_ACCESS_KEY

(read-write) This property gives the Amazon S3 access key used to access the service.

S3_SESSION_TOKEN

(read-write) This property gives the Amazon S3 session token used to access the
service.

S3_BUCKET_LOCATION

(read-write) Location constraint for buckets on Amazon S3. As of this writing, it
can be set to "*" (US Standard, i.e. lowest-latency choice of US East or West),
"us-west-1" (US West, Northern California), "EU" (European Union), or "ap-southeast-1"
(Asia Pacific). See :
http://docs.amazonwebservices.com/general/latest/gr/index.html?rande.html for the most
up-to-date list.

S3_MULTI_DELETE

(read-write) If the server support the multi delete protocol (only Amazon S3), default
is "YES" for "S3" and "AWS4" STORAGE_API, default in "NO" for all others STORAGE_API.

S3_MULTI_PART_UPLOAD

(read-write) If the server support the multi part upload api (only Amazon S3), default
is "NO". Use less s3 objects.

SSL_CA_INFO

(read-write) Path to CA certificate to use to verify the identity of the S3 server.
Only applicable when SSL/TLS is in use. The certificate should be in PEM format if
OpenSSL or GnuTLS is being used with libcurl. Multiple certificates can be bundled
together simply by concatenating them. If NSS is being used, then it is the directory
that the database resides in. The value is passed to curl_easy_setopt(3) as
CURLOPT_CAINFO.

S3_HOST

(read-write) The host name to connect, in the form "hostname:port" or "ip:port",
default is "s3.amazonaws.com"

S3_SECRET_KEY

(read-write) This property gives the Amazon S3 secret key used to access the service.

S3_SERVER_SIDE_ENCRYPTION

(read-write) Set to the server side encryption algorithm to use. There is actually
only one algorithm, it is "AES256". The encryption is done by Amazon on their server.
See :
http://docs.amazonwebservices.com/AmazonS3/latest/API/index.html?RESTObjectPUT.html
for the most up-to-date list.

S3_SERVICE_PATH

(read-write) A path to add at the beginning of the URL.

S3_STORAGE_CLASS

(read-write) Storage class for new objects.

S3 compatible
STANDARD
STANDARD_IA
REDUCED_REDUNDANCY

Google storage
STANDARD
DURABLE_REDUCED_AVAILABILITY
NEARLINE

S3_SSL

(read-write) Whether or not to use SSL/TLS to secure communications with Amazon S3.

S3_SUBDOMAIN

(read-write) Whether or not to use subdomain hostname.

S3_USER_TOKEN

(read-write) This property specifies the user token for Amanda Enterprise Edition
customers.

STORAGE_API

(read-write) Which API to use for the cloud:
S3 Amazon S3 AWS Signature Version 2
AWS4 Amazon S3 AWS Signature Version 4
SWIFT-1.0 Openstack swift v1.0
SWIFT-2.0 Openstack swift v2.0
SWIFT-3 Openstack swift keystone v3
OAUTH2 Google
CASTOR Caringo CAStor

The default is AWS4 if S3-HOST end with '.amazonaws.com', otherwise it is S3.

TENANT_ID

(read-write) The tenant id (for swift v2).

TENANT_NAME

(read-write) The tenant name (for swift v2).

PROJECT_NAME

(read-write) Default: $USERNAME. The project name (for swift v3).

DOMAIN_NAME

(read-write) Default: "Default". The domain name (for swift v3).

TIMEOUT

(read-write) Add a timeout to all transfer to the cloud, default is 0, which is no
timeout.

TRANSITION-TO-GLACIER

(read-write) Default: -1. Set to a value greater or equal to zero to transition a
volume to glacier that number of days after it is set to no-reuse.

USERNAME

(read-write) The username (for swift v2 and v3).

VERBOSE

(read-write) If true, verbose data about each HTTP transaction is sent to the debug
log.

S3 URL
SSL && SUBDOMAIN: https://bucket.host/service_path/file
SSL && !SUBDOMAIN: https://host/service_path/bucket/file
!SSL && SUBDOMAIN: http://bucket.host/service_path/file
!SSL && !SUBDOMAIN: http://host/service_path/bucket/file

Tape Device
tapedev "tape:/dev/nst0"

The tape device driver interacts with a tape drive. The device uses the operating system's
built-in tape support, which is generally similar to that available via the command-line
utilities dd(1) and mt(1).

The tape device name should specify a path to the operating system's device file.

There is no simple way to determine whether a particular system (operating system and tape
hardware) supports LEOM, so as a safe default the tape device has LEOM detection disabled.
However, on modern hardware and common operating systems (Linux, *BSD, and Solaris, at
least), LEOM support is functional. On these systems, enable LEOM by setting the LEOM
property to "true" at the appropriate place in the Amanda configuration.

Device-Specific Properties
Most of these properties are automatically detected, but can be overridden in the
configuration file if the autodetection fails. Note that tape drives are required to at
least support the MTREW (rewind) operation; all other operations can be emulated with the
MTREW and read data operations.

BROKEN_GMT_ONLINE

(read-write) Set this boolean property if the system's GMT_ONLINE macro gives
incorrect results. This is currently true for the Linux IDE-TAPE driver.

BSF

(read-write) This boolean property specifies whether the device
driver may execute the MTBSF operation (backward seek file).

BSF_AFTER_EOM

(read-write) This boolean property specifies whether the device
driver should execute an MTBSF (backward seek file) operation after
MTEOM (seek to end of recorded data) in order to append.

BSR

(read-write) This boolean property specifies whether the device
driver may use the MTBSR operation (backward seek record).

EOM

(read-write) This boolean property specifies whether the device
driver may use the MTEOM command (seek to end of recorded data).

FINAL_FILEMARKS

(read-write) This integer property gives the number of filemarks that should be
written at EOD. It is usually 1 or 2.

FSF

(read-write) This boolean property specifies whether the device driver may use the
MTFSF operation (forward seek file).

FSF_AFTER_FILEMARK

(read-write) This boolean property specifies whether the device driver needs a FSF to
go the next file after the filemark is read. Default to "TRUE" on Solaris and "FALSE"
on all others machines.

FSR

(read-write) This boolean property specifies whether the device driver may use the
MTFSR operation (forward seek record).

NONBLOCKING_OPEN

(read-write) Set this boolean property to "true" if O_NONBLOCK must be used on the
open call. Default to "true" on Linux and "false" on all others machines. Without it,
Linux wait for a few seconds if no tape are loaded. Solaris have strange error it is
set to "yes".

READ_BLOCK_SIZE

(read-write) This property (previously known as READ_BUFFER_SIZE) specifies the block
size that will be used for reads; this should be large enough to contain any block
that may be read from the device (for example, from a tape containing variable-sized
blocks), and must be larger than BLOCK_SIZE. This property is most often used when
overwriting tapes using a new, smaller block size.
The tapetype parameter READBLOCKSIZE sets this property. See BLOCK SIZES, above.

NDMP Device
tapedev "ndmp:my.filer.com:10000@st1"
device-property "NDMP_USERNAME" "jimmy"
device-property "NDMP_PASSWORD" "thelock"

This device enables Amanda to communicate with a tape service on an NDMP server. The
device name specifies the hostname and optionally the TCP port of the NDMP server,
followed by the name of the tape device on the server (st1 in the example above).

This device supports LEOM detection.

Device-Specific Properties
The properties NDMP_USERNAME and NDMP_PASSWORD set the username and password with which to
access the NDMP server. The default for both is "ndmp".

INDIRECT

(read-write) The default is "yes". You can set it to "no" if the ndmp server can be
set to a window length of 0.

NDMP_AUTH

(read-write) Authentication method to use to connect to the NDMP server. One of "md5"
(default), "text", "none" (for an empty authentication attempt) or "void" (for no
authentication attempt at all).

NDMP_PASSWORD

(read-write) Password for md5 or text authentications.

NDMP_USERNAME

(read-write) Username for md5 or text authentications.

READ_BLOCK_SIZE

(read-write) This property specifies the block size that will be used for reads; this
should be large enough to contain any block that may be read from the device and must
be larger than BLOCK_SIZE. See BLOCK_SIZES, above.

VFS Device
tapedev "file:/path/to/vtape"

The VFS device driver stores data on a UNIX filesystem. Note that although one typically
uses the VFS device driver to store data on hard disks, the driver does not interface with
any hardware on a block level.

The device name specifies a path to a directory which must exist and contain a "data/"
subdirectory. Each tape file is stored as a distinct file in this directory, the name of
which reflects the Amanda header in the tape file. Block boundaries are not maintained:
the driver supports reads of arbitrary size, regardless of the blocksize used to write the
data.

This device supports LEOM detection. LEOM will be indicated when the MAX_VOLUME_USAGE is
nearly met, or when the filesystem is nearly out of space. The latter circumstance is
detected by monitoring the available space on the filesystem, and this monitoring can be
disabled with the MONITOR_FREE_SPACE property. Note that the device cannot detect other
circumstances that may cause a write to fail, such as a filesystem quota. LEOM detection
can be disabled by setting the LEOM property to false.

This device supports the ENFORCE_MAX_VOLUME_USAGE property. Default value is true. See
COMMON PROPERTIES, above.

Device-Specific Properties
MONITOR_FREE_SPACE

(read-write) This property controls whether the device will monitor the filesystem's
free space to detect a full filesystem before an error occurs, and defaults to true.
The monitoring operation works on most filesystems, but if it causes problems, use
this property to disable it.

USE_DATA

(read-write) (Default: "EXIST") This property controls whether the device use the
'data' subdirectory, A value of "NO" never use it. A value of "YES" always use it. A
value of "EXIST" use it only if it exist.

DISKFLAT Device
tapedev "diskflat:/path/to/diskflat/label-001"

Each slot is a single file named with the slot label.

The MAX-DLE-BY-VOLUME setting must be set to 1.

Must be used with the multi changer.
tpchanger "chg-multi:diskflat:/path/to/diskflat/label-{001..010}"
autolabel "label-$3s" empty volume-error
labelstr MATCH-AUTOLABEL
max-dle-by-volume 1

Device-Specific Properties
Have the same property as the VFS device with the following difference:

USE_DATA
Unused

DVD-RW Device
tapedev "dvdrw:/var/cache/amanda/dvd-cache:/dev/scd0"
device-property "DVDRW_MOUNT_POINT" "/media/dvd"
device-property "DVDRW_KEEP_CACHE" "false"
device-property "DVDRW_UNLABELLED_WHEN_UNMOUNTABLE" "true"

The DVD-RW device driver reads and writes optical media such as DVDs and CDs. The device
name must specify a cache directory for data to be temporarily stored, followed by the
operating system name for the optical drive. The cache directory must contain a "data/"
subdirectory.

The DVDRW_MOUNT_POINT property is required, and specifies a directory where the optical
media can be mounted. This directory must be configured to enable non-root users to mount
the optical media. On Linux, that means a line similar to the following in /etc/fstab:
/dev/scd0 /media/dvd auto ro,user,noauto 0 0

Note the "user" option.

When writing data, the device acts as a VFS device using the given cache directory. On
completion of writing the tape, the cache directory is written to optical media. The
DVDRW_KEEP_CACHE property controls whether the cache contents are immediately deleted.
When reading, the optical media is first mounted and read as a VFS device.

Attempting to mount unformatted media or media that is formatted but contains no
filesystem will usually result in an error. The boolean DVDRW_UNLABELLED_WHEN_UNMOUNTABLE
property specifies whether media that cannot be mounted should be treated as an empty,
unlabelled volume when attempting to read the volume label. It is necessary to set this
property to "true" when labelling such media.

This device does not support LEOM detection.

Device-Specific Properties
The properties DVDRW_GROWISOFS_COMMAND, DVDRW_MOUNT_COMMAND and DVDRW_UMOUNT_COMMAND
specify alternative commands for writing, mounting and unmounting optical media. The
default is to find the programs using the PATH environment variable.

The CDRW device supports all of the properties of the VFS device, as well as the
properties given below. The DVDRW_MOUNT_POINT property is required. Other properties are
optional.

DVDRW_KEEP_CACHE

(read-write) Set this boolean property to "true" if the disk cache directory should
be kept after successfully writing tape data to optical media. The default is false,
which causes the cache contents to be deleted immediately after a successful write
operation.

DVDRW_MOUNT_POINT

(read-write) This property specifies the filesystem mount point for the optical
media. Non-root users must be able to mount optical media by invoking "mount" and
specifying this mount point.

DVDRW_UNLABELLED_WHEN_UNMOUNTABLE

(read-write) Treat unmountable media as empty, unlabelled media. This is necessary
when attempting to label freshly formatted media.

DVDRW_GROWISOFS_COMMAND

(read-write) The command to invoke to burn the DVD.

DVDRW_MOUNT_COMMAND

(read-write) The command to invoke to mount the DVD.

DVDRW_UMOUNT_COMMAND

(read-write) The command to invoke to unmount the DVD.

AUTHORS