NAME

       fence_cisco_mds - Fence agent for Cisco MDS

DESCRIPTION

       fence_cisco_mds  is  an I/O Fencing agent which can be used with any Cisco MDS 9000 series
       with SNMP enabled device.

       fence_cisco_mds accepts options on the command line as well as from  stdin.  Fenced  sends
       parameters  through  stdin  when  it execs the agent. fence_cisco_mds can be run by itself
       with command line options.  This is useful for testing and for turning outlets on  or  off
       from scripts.

       Vendor URL: http://www.cisco.com

PARAMETERS

       -o, --action=[action]
              Fencing action (Default Value: off)

       -c, --community=[community]
              Set the community string

       -4, --inet4-only
              Forces agent to use IPv4 addresses only

       -6, --inet6-only
              Forces agent to use IPv6 addresses only

       -a, --ip=[ip]
              IP  address or hostname of fencing device This parameter is always required.

       -u, --ipport=[port]
              TCP/UDP port to use for connection with device (Default  Value:  161)

       -p, --password=[password]
              Login password or passphrase

       -S, --password-script=[script]
              Script to run to retrieve password

       -n, --plug=[id]
              Physical plug number on device, UUID or identification of machine This parameter is
              always required.

       -b, --snmp-auth-prot=[prot]
              Set authentication protocol (MD5|SHA)

       -P, --snmp-priv-passwd=[pass]
              Set privacy protocol password

       -R, --snmp-priv-passwd-script
              Script to run to retrieve privacy password

       -B, --snmp-priv-prot=[prot]
              Set privacy protocol (DES|AES)

       -E, --snmp-sec-level=[level]
              Set security level (noAuthNoPriv|authNoPriv|authPriv)

       -d, --snmp-version=[version]
              Specifies SNMP version to use (1|2c|3)

       -l, --username=[name]
              Login name

       -q, --quiet
              Disable logging to stderr. Does not affect --verbose or --debug logging to  syslog.

       -v, --verbose
              Verbose mode

       -D, --debug-file=[debugfile]
              Write debug information to given file

       -V, --version
              Display version information and exit

       -h, --help
              Display help and exit

       -C, --separator=[char]
              Separator for CSV created by 'list' operation (Default Value: ,)

       --delay=[seconds]
              Wait X seconds before fencing is started (Default Value: 0)

       --login-timeout=[seconds]
              Wait X seconds for cmd prompt after login (Default Value: 5)

       --power-timeout=[seconds]
              Test X seconds for status change after ON/OFF (Default Value: 20)

       --power-wait=[seconds]
              Wait X seconds after issuing ON/OFF (Default Value: 0)

       --shell-timeout=[seconds]
              Wait X seconds for cmd prompt after issuing command (Default Value: 3)

       --retry-on=[attempts]
              Count of attempts to retry power on (Default Value: 1)

       --snmpget-path=[path]
              Path to snmpget binary (Default Value: /usr/bin/snmpget)

       --snmpset-path=[path]
              Path to snmpset binary (Default Value: /usr/bin/snmpset)

       --snmpwalk-path=[path]
              Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)

ACTIONS

       on     Power on machine.

       off    Power off machine.

       status This returns the status of the plug/virtual machine.

       list   List  available  plugs  with  aliases/virtual machines if there is support for more
              then one device. Returns N/A otherwise.

       list-status
              List available plugs with aliases/virtual machines and their power state if it  can
              be obtained without additional commands.

       monitor
              Check the health of fence device

       metadata
              Display the XML metadata describing this resource.

       validate-all
              Validate if all required parameters are entered.

STDIN PARAMETERS

       action Fencing action (Default Value: off)

       community
              Set the community string

       inet4_only
              Forces agent to use IPv4 addresses only

       inet6_only
              Forces agent to use IPv6 addresses only

       ip     IP  address  or  hostname  of  fencing  device  This  parameter is always required.
              Obsoletes: ipaddr

       ipport TCP/UDP port to use for connection with device (Default  Value:  161)

       password
              Login password or passphrase Obsoletes: passwd

       password_script
              Script to run to retrieve password Obsoletes: passwd_script

       plug   Physical plug number on device, UUID or identification of machine This parameter is
              always required. Obsoletes: port

       snmp_auth_prot
              Set authentication protocol (MD5|SHA)

       snmp_priv_passwd
              Set privacy protocol password

       snmp_priv_passwd_script
              Script to run to retrieve privacy password

       snmp_priv_prot
              Set privacy protocol (DES|AES)

       snmp_sec_level
              Set security level (noAuthNoPriv|authNoPriv|authPriv)

       snmp_version
              Specifies SNMP version to use (1|2c|3)

       username
              Login name Obsoletes: login

       quiet  Disable logging to stderr. Does not affect --verbose or --debug logging to  syslog.

       verbose
              Verbose mode

       debug_file
              Write debug information to given file Obsoletes: debug

       version
              Display version information and exit

       help   Display help and exit

       separator
              Separator for CSV created by 'list' operation (Default Value: ,)

       delay  Wait X seconds before fencing is started (Default Value: 0)

       login_timeout
              Wait X seconds for cmd prompt after login (Default Value: 5)

       power_timeout
              Test X seconds for status change after ON/OFF (Default Value: 20)

       power_wait
              Wait X seconds after issuing ON/OFF (Default Value: 0)

       shell_timeout
              Wait X seconds for cmd prompt after issuing command (Default Value: 3)

       retry_on
              Count of attempts to retry power on (Default Value: 1)

       snmpget_path
              Path to snmpget binary (Default Value: /usr/bin/snmpget)

       snmpset_path
              Path to snmpset binary (Default Value: /usr/bin/snmpset)

       snmpwalk_path
              Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)