Provided by: iodine_0.7.0-7_amd64 
NAME
iodine, iodined - tunnel IPv4 over DNS
SYNOPSIS
iodine [-v]
iodine [-h]
iodine [-4] [-6] [-f] [-r] [-u user ] [-P password ] [-m fragsize ] [-t chrootdir ] [-d
device ] [-R rdomain ] [-m fragsize ] [-M namelen ] [-z context ] [-F pidfile ] [-T
dnstype ] [-O downenc ] [-L 0|1 ] [-I interval ] [ nameserver ] topdomain
iodined [-v]
iodined [-h]
iodined [-c] [-s] [-f] [-D] [-u user ] [-t chrootdir ] [-d device ] [-m mtu ] [-l
listen_ip ] [-p port ] [-n ( auto | external_ip ) ] [-b dnsport ] [-P password ] [-z
context ] [-F pidfile ] [-i max_idle_time ] tunnel_ip [ /netmask ] topdomain
DESCRIPTION
iodine lets you tunnel IPv4 data through a DNS server. This can be useful in situations
where Internet access is firewalled, but DNS queries are allowed. It needs a TUN/TAP
device to operate. The bandwidth is asymmetrical, with a measured maximum of 680 kbit/s
upstream and 2.3 Mbit/s downstream in a wired LAN test network. Realistic sustained
throughput on a Wifi network using a carrier-grade DNS cache has been measured at some 50
kbit/s upstream and over 200 kbit/s downstream. iodine is the client application, iodined
is the server.
Note: server and client are required to speak the exact same protocol. In most cases, this
means running the same iodine version. Unfortunately, implementing backward and forward
protocol compatibility is usually not feasible.
OPTIONS
Common Options:
-v Print version info and exit.
-h Print usage info and exit.
-f Keep running in foreground.
-u user
Drop privileges and run as user 'user' after setting up tunnel.
-t chrootdir
Chroot to 'chrootdir' after setting up tunnel.
-d device
Use the TUN device 'device' instead of the normal one, which is dnsX on Linux and
otherwise tunX.
-P password
Use 'password' to authenticate. If not used, stdin will be used as input. Only the
first 32 characters will be used.
-z context
Apply SELinux 'context' after initialization.
-F pidfile
Create 'pidfile' and write process id in it.
Client Options:
-4 Force IPv4 DNS queries
-6 Force IPv6 DNS queries
-r Skip raw UDP mode. If not used, iodine will try getting the public IP address of
the iodined host and test if it is reachable directly. If it is, traffic will be
sent to the server instead of the DNS relay.
-R rdomain
Use OpenBSD routing domain 'rdomain' for the DNS connection.
-m fragsize
Force maximum downstream fragment size. Not setting this will cause the client to
automatically probe the maximum accepted downstream fragment size.
-M namelen
Maximum length of upstream hostnames, default 255. Usable range ca. 100 to 255.
Use this option to scale back upstream bandwidth in favor of downstream bandwidth.
Also useful for DNS servers that perform unreliably when using full-length
hostnames, noticeable when fragment size autoprobe returns very different results
each time.
-T dnstype
DNS request type override. By default, autodetection will probe for working DNS
request types, and will select the request type that is expected to provide the
most bandwidth. However, it may turn out that a DNS relay imposes limits that skew
the picture, which may lead to an "unexpected" DNS request type providing more
bandwidth. In that case, use this option to override the autodetection. In
(expected) decreasing bandwidth order, the supported DNS request types are: NULL,
PRIVATE, TXT, SRV, MX, CNAME and A (returning CNAME). Note that SRV, MX and A
may/will cause additional lookups by "smart" caching nameservers to get an actual
IP address, which may either slow down or fail completely. The PRIVATE type uses
value 65399 (in the 'private use' range) and requires servers implementing RFC
3597.
-O downenc
Force downstream encoding type for all query type responses except NULL. Default
is autodetected, but may not spot all problems for the more advanced codecs. Use
this option to override the autodetection. Base32 is the lowest-grade codec and
should always work; this is used when autodetection fails. Base64 provides more
bandwidth, but may not work on all nameservers. Base64u is equal to Base64 except
in using underscore ('_') instead of plus sign ('+'), possibly working where Base64
does not. Base128 uses high byte values (mostly accented letters in iso8859-1),
which might work with some nameservers. For TXT queries, Raw will provide maximum
performance, but this will only work if the nameserver path is fully 8-bit-clean
for responses that are assumed to be "legible text".
-L 0|1 Lazy-mode switch. -L1 (default): Use lazy mode for improved performance and
decreased latency. A very small minority of DNS relays appears to be unable to
handle the lazy mode traffic pattern, resulting in no or very little data coming
through. The iodine client will detect this and try to switch back to legacy mode,
but this may not always work. In these situations use -L0 to force running in
legacy mode (implies -I1).
-I interval
Maximum interval between requests (pings) so that intermediate DNS servers will not
time out. Default is 4 in lazy mode, which will work fine in most cases. When too
many SERVFAIL errors occur, iodine will automatically reduce this to 1. To get
absolute minimum DNS traffic, increase well above 4, but not so high that SERVFAIL
errors start to occur. There are some DNS relays with very small timeouts, notably
dnsadvantage.com (ultradns), that will give SERVFAIL errors even with -I1; data
will still get trough, and these errors can be ignored. Maximum useful value is
59, since iodined will close a client's connection after 60 seconds of inactivity.
Server Options:
-c Disable checking the client IP address on all incoming requests. By default,
requests originating from non-matching IP addresses will be rejected, however this
will cause problems when requests are routed via a cluster of DNS servers.
-s Don't try to configure IP address or MTU. This should only be used if you have
already configured the device that will be used.
-D Increase debug level. Level 1 prints info about each RX/TX packet. Implies the -f
option. On level 2 (-DD) or higher, DNS queries will be printed literally. When
using Base128 upstream encoding, this is best viewed as ISO Latin-1 text instead of
(illegal) UTF-8. This is easily done with : "LC_ALL=C luit iodined -DD ..." (see
luit(1)).
-m mtu Set 'mtu' as mtu size for the tun device. This will be sent to the client on
login, and the client will use the same mtu for its tun device. Default 1130.
Note that the DNS traffic will be automatically fragmented when needed.
-l listen_ip
Make the server listen only on 'listen_ip' for incoming requests. By default,
incoming requests are accepted from all interfaces.
-p port
Make the server listen on 'port' instead of 53 for traffic. If 'listen_ip' does
not include localhost, this 'port' can be the same as 'dnsport'. Note: You must
make sure the dns requests are forwarded to this port yourself.
-n auto|external_ip
The IP address to return in NS responses. Default is to return the address used as
destination in the query. If external_ip is 'auto', iodined will use
externalip.net web service to retrieve the external IP of the host and use that for
NS responses.
-b dnsport
If this port is specified, all incoming requests not inside the tunnel domain will
be forwarded to this port on localhost, to be handled by a real dns. If
'listen_ip' does not include localhost, this 'dnsport' can be the same as 'port'.
Note: The forwarding is not fully transparent, and not advised for use in
production environments.
-i max_idle_time
Make the server stop itself after max_idle_time seconds if no traffic have been
received. This should be combined with systemd or upstart on demand activation for
being effective.
Client Arguments:
nameserver
The nameserver to use to relay the dns traffic. This can be any relaying nameserver
or the server running iodined if reachable. This field can be given as an IPv4/IPv6
address or as a hostname. This argument is optional, and if not specified a
nameserver will be read from the /etc/resolv.conf file.
topdomain
The dns traffic will be sent as queries for subdomains under ´topdomain'. This is
normally a subdomain to a domain you own. Use a short domain name to get better
throughput. If nameserver is the iodined server, then the topdomain can be chosen
freely. This argument must be the same on both the client and the server.
Server Arguments:
tunnel_ip[/netmask]
This is the server's ip address on the tun interface. The client will be given the
next ip number in the range. It is recommended to use the 10.0.0.0 or 172.16.0.0
ranges. The default netmask is /27, can be overridden by specifying it here. Using
a smaller network will limit the number of concurrent users.
topdomain
The dns traffic is expected to arrive as queries for subdomains under 'topdomain'.
This is normally a subdomain to a domain you own. Use a short domain name to get
better throughput. This argument must be the same on both the client and the
server. Queries for domains other than 'topdomain' will be forwarded when the -b
option is given, otherwise they will be dropped.
EXAMPLES
See the README file for both a quick test scenario, and a detailed description of real-
world deployment.
SECURITY
Login is a relatively secure challenge-response MD5 hash, with the password never passing
the wire. However, all other data is NOT encrypted in any way. The DNS traffic is also
vulnerable to replay, injection and man-in-the-middle attacks, especially when iodined is
used with the -c option. Use of ssh or vpn tunneling is strongly recommended. On both
server and client, use iptables, pf or other firewalls to block all traffic coming in from
the tun interfaces, except to the used ssh or vpn ports.
ENVIRONMENT
IODINE_PASS
If the environment variable IODINE_PASS is set, iodine will use the value it is set to as
password instead of asking for one. The -P option still has precedence.
IODINED_PASS
If the environment variable IODINED_PASS is set, iodined will use the value it is set to
as password instead of asking for one. The -P option still has precedence.
SEE ALSO
The README file in the source distribution contains some more elaborate information.
BUGS
File bugs at http://dev.kryo.se/iodine/
AUTHORS
Erik Ekman <yarrick@kryo.se> and Bjorn Andersson <flex@kryo.se>. Major contributions by
Anne Bezemer.