Provided by: snapper_0.5.4-3_amd64 
NAME
snapper - Command-line program for filesystem snapshot management
SYNOPSIS
snapper [--global-opts] command [--command-opts] [command-arguments]
snapper {--help}
DESCRIPTION
Snapper is a command-line program for filesystem snapshot management. It can create, delete and compare
snapshots and undo changes done between snapshots.
Snapper never modifies the content of snapshots. Thus snapper creates read-only snapshots if supported by
the kernel. Supported filesystems are btrfs and ext4 as well as snapshots of LVM logical volumes with
thin-provisioning. Some filesystems might not be supported depending on your installation.
CONCEPTS
Configurations
For each filesystem or subvolume that should be snapshotted by snapper, a configuration file is required,
see snapper-configs(5). The setup can be done with the create-config command.
Snapshots
Snapper distinguishes three types of snapshots.
pre
Pre snapshots should always have a corresponding post snapshot. The intention of pre/post snapshot
pairs is to snapshot the filesystem before and after a modification.
post
See pre type.
single
These snapshots have no special relationship to other snapshots.
Note that filesystem-wise all three types are the same.
Snapshot Description and Userdata
With each snapshot a description and some userdata can be associated. The description is a string. The
userdata is a list of key-value pairs where the keys and values are strings.
Automatic Snapshot Creation
Next to manual snapshot creation, snapshots are also created automatically.
• A cron-job creates hourly snapshots.
• Certain programs like YaST and zypper create pre/post snapshot pairs when modifying the system.
Cleanup Algorithms
Snapper provides several algorithms to clean up old snapshots. The algorithms are executed in a daily
cron-job. This can be configured in the corresponding configurations files along with parameters for
every algorithm.
number
Deletes old snapshots when a certain number of snapshots is reached.
timeline
Deletes old snapshots but keeps a number of hourly, daily, weekly, monthly and yearly snapshots.
empty-pre-post
Deletes pre/post snapshot pairs with empty diffs.
The number and timeline cleanup algorithm can also try to keep the space used by snapshots below a limit.
For that quota must be setup, see command setup-quota, and the LIMIT variables in the config file must
have ranges (min- and max-value). The algorithms will then make two passes:
1. Delete snapshots above the max-value independent of the used space.
2. Delete snapshots above the min-value until the limit for the used space is reached.
The limit for the used space can be configured via the SPACE_LIMIT variable. Note: Only snapshots that
have a cleanup algorithm set are taken into account when calculating the used space.
Filters
Some files keep state information of the system, e.g. /etc/mtab. Such files should never be reverted. To
help users, snapper allows one to ignore these files.
Each line in all files /etc/snapper/filters/*.txt specifies a pattern. When snapper computes the
difference between two snapshots it ignores all files and directories matching any of those patterns by
using fnmatch(3) with the flag FNM_LEADING_DIR.
Note that filters do not exclude files or directories from being snapshotted. For that, use subvolumes or
mount points.
GLOBAL OPTIONS
-q, --quiet
Suppress normal output. Error messages will still be printed, though.
-v, --verbose
Increase verbosity.
--utc
Display dates and times in UTC.
--iso
Display dates and times in ISO format.
-t, --table-style
Specifies table style. Table style is identified by an integer number.
-c, --config name
Use specified configuration instead of the default configuration. The default configuration is named
"root".
--no-dbus
Operate without a DBus connection.
Use with caution since a running snapperd will not know about modifications made to the system.
-r, --root path
Operate on target root. Only works together with no-dbus and only for some commands.
--version
Print version and exit.
COMMANDS
Snapper provides a number of commands. Each command accepts the options listed in the GLOBAL OPTIONS
section. These options must be specified before the command name. In addition, many commands have
specific options, which are listed in this section. These command-specific options must be specified
after the name of the command and before any of the command arguments.
help
Show short help text.
list-configs
List available configurations.
create-config [options] subvolume
Create a new configuration for a filesystem or subvolume. For this command you will likely need the
global option --config, see GLOBAL OPTIONS and CONCEPTS.
-f, --fstype fstype
Manually set filesystem type. Supported values are btrfs, ext4 and lvm. For lvm, snapper uses LVM
thin-provisioned snapshots. The filesystem type on top of LVM must be provided in parentheses,
e.g. lvm(xfs).
Without this option snapper tries to detect the filesystem.
-t, --template name
Name of template for the new configuration file.
delete-config
Delete a configuration for a filesystem or subvolume. For this command you will likely need to global
option --config, see GLOBAL OPTIONS and CONCEPTS.
get-config
Displays the settings of the configuration.
set-config configdata
Changes the settings of the configuration. The settings configdata are a list of key-value-pairs
separated by spaces and the key and value must be separated by an equal sign, e.g.
"NUMBER_CLEANUP=yes NUMBER_LIMIT=10". The value of SUBVOLUME and FSTYPE cannot be changed.
list (ls) [options]
List snapshots.
-t, --type type
Selects type of snapshots to list. Possible values are all, single and pre-post.
-a, --all-configs
List snapshots from all configs accessible by the user.
create [options]
Create a new snapshot.
-t, --type type
Specifies the type of the new snapshot. Possible values are single, pre and post.
--pre-number number
For post snapshots the number of the pre snapshot must be provided.
-p, --print-number
Print number of the created snapshot.
-d, --description description
Description for the snapshot.
-c, --cleanup-algorithm cleanup-algorithm
Set the cleanup algorithm for the snapshot.
-u, --userdata userdata
Set userdata for the snapshot. The key-value pairs must be separated by comma and the key and
value must be separated by an equal sign, e.g. requestid=42,user=arthur.
--command command
Create a pre and post snapshot and run command in between.
modify [options] number
Modify a snapshot.
-d, --description description
New description for snapshot.
-c, --cleanup-algorithm cleanup-algorithm
Set the cleanup algorithm for the snapshot.
-u, --userdata userdata
Set userdata for the snapshot. The key-value pairs must be separated by comma and the key and
value must be separated by an equal sign, e.g. requestid=42,user=arthur.
delete (remove|rm) number | number1-number2
Delete a snapshot or a range of snapshots.
-s, --sync
Sync the filesystem after deleting the snapshots. The details depend on the filesystem type.
Btrfs normally asynchronously frees space after deleting snapshots. With this option snapper will
wait until the space once used by the deleted snapshots is actually available again.
mount number
Mount a snapshot. Not required for all filesystem types.
umount number
Unmount a snapshot. Not required for all filesystem types.
status [options] number1..number2
Compare the snapshots number1 and number2. This will show a list of files and directories that have
been created, modified or deleted in the time between the two snapshots have been made.
-o, --output file
Write output to file file.
The output consists of a string encoding the status followed by the filename. The characters of the
status string are:
1. A "+" means the file was created, a "-" means the file was deleted. A "c" means the content of
the file has changed and a "t" means the type of the file has changed (e.g. from regular file to
directory).
2. A "p" means the permissions are have changed.
3. An "u" means the user ownership has changed.
4. A "g" means the group ownership has changed.
5. A "x" means the extended attribute information has changed.
6. An "a" means the ACL information has changed.
If there is no change a "." is outputted.
diff [options] number1..number2 [files]
Compare the snapshots number1 and number2. This will show a diff of the content of files and
directories that have been created, modified or deleted in the time between the two snapshots have
been made.
-i, --input file
Read files to diff from file file.
--diff-cmd command
Command used for comparing files. The default is /usr/bin/diff --new-file --unified. The two
files to compare are passed as parameters to the command.
-x, --extensions options
Extra options passed to the diff command.
undochange [options] number1..number2 [files]
Undo changes done between snapshot number1 and number2.
-i, --input file
Read files for which to undo changes from file file.
rollback [options] [number]
Creates two new snapshots and sets the default subvolume. Per default the system boots from the
default subvolume of the root filesystem. The exact actions depend on whether a number is provided or
not:
• Without a number, a first read-only snapshot of the default subvolume is created. A second
read-write snapshot of the current system is created. The system is set to boot from the second
snapshot.
• With a number, a first read-only snapshot of the current system is created. A second read-write
snapshot is created of number. The system is set to boot from the second snapshot.
Rollback is only supported with btrfs and requires a properly configured system.
-p, --print-number
Print number of the second created snapshot.
-d, --description description
Description for the snapshot.
-c, --cleanup-algorithm cleanup-algorithm
Set the cleanup algorithm for the snapshot.
-u, --userdata userdata
Set userdata for the snapshot. The key-value pairs must be separated by comma and the key and
value must be separated by an equal sign, e.g. requestid=42,user=arthur.
The rollback command also sets the description, the cleanup algorithm and some userdata unless the
values are specified on the command line. This will automate cleanup of snapshots created by
rollbacks.
setup-quota
Sets up quota. Currently only supported with btrfs.
cleanup cleanup-algorithm
Run the cleanup algorithm cleanup-algorithm. Currently implemented cleanup algorithms are number,
timeline and empty-pre-post.
xadiff number1..number2 [files]
Compare the extended attributes between snapshot number1 and number2. See examples below:
• +:user.foo for created attributes
• -:user.bar for removed attributes
• -+:security.selinux for modified attributes
PERMISSIONS
Non-root users can be allowed to use a configuration by setting ALLOW_USERS or ALLOW_GROUPS in the config
file. For all operations to work, the user must also be able to read and access the .snapshots directory
inside the subvolume. The .snapshots directory must be owned by root and must not be writable by anybody
else.
Here are some methods how to achieve that:
• Make the directory accessible for everyone:
chmod a+rx .snapshots
• Make the directory accessible for a group the user belongs to, e.g.:
chown :users .snapshots
• Make the directory accessible for the user using ACLs, e.g.:
setfacl -m u:tux:rx .snapshots
The last method can be performed by snapper, see the SYNC_ACL setting in snapper-configs(5).
FILES
/etc/default/snapper
Global configuration file.
/etc/snapper/configs
Directory containing configuration files.
/etc/snapper/config-templates
Directory containing configuration templates.
/etc/snapper/filters/*.txt
Filter files.
/var/log/snapper.log
Logfile. Please include this file in bug reports.
NOTES
There is no mechanism to ensure consistency of the files while a snapshot it made. E.g. the files of a
database can be inconsistent while the database is running.
Consistency after undochange is not guaranteed. E.g. when the creation of a user is undone, there might
still exist files from that user.
Support for individual filesystems, rollback and extended attributes are compile-time options and may not
be available.
HOMEPAGE
http://snapper.io/
AUTHORS
Arvin Schnell <aschnell@suse.com>
SEE ALSO
snapper-configs(5), snapper-zypp-plugin(8), pam_snapper(8), btrfs(8), lvm(8), attr(5), acl(5)