NAME

       ematch - extended matches for use with "basic", "cgroup"  or "flow" filters

SYNOPSIS

       tc filter add .. basic match EXPR .. flowid ..

       EXPR := TERM [ { and | or } EXPR ]

       TERM := [ not ] { MATCH | '(' EXPR ')' }

       MATCH := module '(' ARGS ')'

       ARGS := ARG1 ARG2 ..

MATCHES

   cmp
       Simple comparison ematch: arithmetic compare of packet data to a given value.

       cmp( ALIGN at OFFSET [ ATTRS ] { eq | lt | gt } VALUE )

       ALIGN := { u8 | u16 | u32 }

       ATTRS := [ layer LAYER ] [ mask MASK ] [ trans ]

       LAYER := { link | network | transport | 0..2 }

   meta
       Metadata ematch

       meta( OBJECT { eq | lt |gt } OBJECT )

       OBJECT := { META_ID |  VALUE }

       META_ID := id [ shift SHIFT ] [ mask MASK ]

       meta attributes:

              random 32 bit random value

              loadavg_1 Load average in last 5 minutes

              nf_mark Netfilter mark

              vlan Vlan tag

              sk_rcvbuf Receive buffer size

              sk_snd_queue Send queue length

       A full list of meta attributes can be obtained via

       # tc filter add dev eth1 basic match 'meta(list)'

   nbyte
       match packet data byte sequence

       nbyte( NEEDLE at OFFSET [ layer LAYER ] )

       NEEDLE := { string | c-escape-sequence  }

       OFFSET := int

       LAYER := { link | network | transport | 0..2 }

   u32
       u32 ematch

       u32( ALIGN VALUE MASK at [ nexthdr+ ] OFFSET )

       ALIGN := { u8 | u16 | u32 }

   ipset
       test packet against ipset membership

       ipset( SETNAME FLAGS )

       SETNAME := string

       FLAGS := { FLAG [, FLAGS] }

       The flag options are the same as those used by the iptables "set" match.

       When using the ipset ematch with the "ip_set_hash:net,iface" set type, the interface can
       be queried using "src,dst (source ip address, outgoing interface) or "src,src" (source ip
       address, incoming interface) syntax.

   ipt
       test packet against xtables matches

       ipt( [-6] -m MATCH_NAME FLAGS )

       MATCH_NAME := string

       FLAGS := { FLAG [, FLAGS] }

       The flag options are the same as those used by the xtable match used.

   canid
       ematch rule to match CAN frames

       canid( IDLIST )

       IDLIST :=  IDSPEC[IDLIST]

       IDSPEC := { ’sff’ CANID | ’eff’ CANID }

       CANID := ID[:MASK]

       ID, MASK := hexadecimal number (i.e. 0x123)

CAVEATS

       The ematch syntax uses '(' and ')' to group expressions. All braces need to be escaped
       properly to prevent shell commandline from interpreting these directly.

       When using the ipset ematch with the "ifb" device, the outgoing device will be the ifb
       device itself, e.g. "ifb0".  The original interface (i.e. the device the packet arrived
       on) is treated as the incoming interface.

EXAMPLE & USAGE

       # tc filter add .. basic match ...

       # 'cmp(u16 at 3 layer 2 mask 0xff00 gt 20)'

       # 'meta(nfmark gt 24)' and 'meta(tcindex mask 0xf0 eq 0xf0)'

       # 'nbyte("ababa" at 12 layer 1)'

       # 'u32(u16 0x1122 0xffff at nexthdr+4)'

       Check if packet source ip address is member of set named bulk:

       # 'ipset(bulk src)'

       Check if packet source ip and the interface the packet arrived on is member of
       "hash:net,iface" set named interactive:

       # 'ipset(interactive src,src)'

       Check if packet matches an IPSec state with reqid 1:

       # 'ipt(-m policy --dir in --pol ipsec --reqid 1)'

AUTHOR

       The extended match infrastructure was added by Thomas Graf.