Provided by: freebsd-manpages_12.0-1_all bug

NAME

     ng_etf — Ethertype filtering netgraph node type

SYNOPSIS

     #include <netgraph.h>
     #include <netgraph/ng_etf.h>

DESCRIPTION

     The etf node type multiplexes and filters data between hooks on the basis of the ethertype
     found in an Ethernet header, presumed to be in the first 14 bytes of the data.  Incoming
     Ethernet frames are accepted on the downstream hook and if the ethertype matches a value
     which the node has been configured to filter, the packet is forwarded out the hook which was
     identified at the time that value was configured.  If it does not match a configured value,
     it is passed to the nomatch hook.  If the nomatch hook is not connected, the packet is
     dropped.

     Packets travelling in the other direction (towards the downstream hook) are also examined
     and filtered.  If a packet has an ethertype that matches one of the values configured into
     the node, it must have arrived in on the hook for which that value was configured, otherwise
     it will be discarded.  Ethertypes of values other than those configured by the control
     messages must have arrived via the nomatch hook.

HOOKS

     This node type supports the following hooks:

     downstream        Typically this hook would be connected to a ng_ether(4) node, using the
                       lower hook.

     nomatch           Typically this hook would also be connected to an ng_ether(4) type node
                       using the upper hook.

     ⟨any legal name⟩  Any other hook name will be accepted and can be used as the match target
                       of an ethertype.  Typically this hook would be attached to a protocol
                       handling node that requires and generates packets with a particular set of
                       ethertypes.

CONTROL MESSAGES

     This node type supports the generic control messages, plus the following:

     NGM_ETF_GET_STATUS (getstatus)
           This command returns a struct ng_etfstat containing node statistics for packet counts.

     NGM_ETF_SET_FILTER (setfilter)
           Sets the a new ethertype filter into the node and specifies the hook to and from which
           packets of that type should use.  The hook and ethertype are specified in a structure
           of type struct ng_etffilter:

               struct ng_etffilter {
                   char        matchhook[NG_HOOKSIZ];  /* hook name */
                   uint16_t    ethertype;              /* this ethertype to this hook */
               };

EXAMPLES

     Using ngctl(8) it is possible to set a filter in place from the command line as follows:

         #!/bin/sh
         ETHER_IF=fxp0
         MATCH1=0x834
         MATCH2=0x835
         cat <<DONE >/tmp/xwert
         # Make a new ethertype filter and attach to the Ethernet lower hook.
         # first remove left over bits from last time.
         shutdown ${ETHER_IF}:lower
         mkpeer ${ETHER_IF}: etf lower downstream
         # Give it a name to easily refer to it.
         name ${ETHER_IF}:lower etf
         # Connect the nomatch hook to the upper part of the same interface.
         # All unmatched packets will act as if the filter is not present.
         connect ${ETHER_IF}: etf: upper nomatch
         DONE
         ngctl -f /tmp/xwert

         # something to set a hook to catch packets and show them.
         echo "Unrecognised packets:"
         nghook -a etf: newproto &
         # Filter two random ethertypes to that hook.
         ngctl 'msg etf: setfilter { matchhook="newproto" ethertype=${MATCH1} }
         ngctl 'msg etf: setfilter { matchhook="newproto" ethertype=${MATCH2} }

SHUTDOWN

     This node shuts down upon receipt of a NGM_SHUTDOWN control message, or when all hooks have
     been disconnected.

SEE ALSO

     netgraph(4), ng_ether(4), ngctl(8), nghook(8)

HISTORY

     The ng_etf node type was implemented in FreeBSD 5.0.

AUTHORS

     Julian Elischer <julian@FreeBSD.org>