Ubuntu Manpage: sym — NCR/Symbios/LSI Logic 53C8XX PCI SCSI host adapter driver

Provided by: freebsd-manpages_12.0-1_all

NAME

     sym — NCR/Symbios/LSI Logic 53C8XX PCI SCSI host adapter driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel
     configuration file:

           device pci
           device scbus
           device sym

           To disable PCI parity checking (needed for broken bridges):
           options SYM_SETUP_PCI_PARITY=<boolean>

           To control driver probing against HVD buses:
           options SYM_SETUP_SCSI_DIFF=<bit combination>

           To control chip attachment balancing between the ncr driver and this driver:
           options SYM_SETUP_LP_PROBE_MAP=<bit combination>

     Alternatively, to load the driver as a module at boot time, place the following line in
     loader.conf(5):

           sym_load="YES"

DESCRIPTION

This driver provides support for the Symbios/LSI Logic 53C8XX PCI SCSI controllers.

Driver features include support for wide SCSI busses and fast10, fast20, fast40 and
fast80-dt synchronous data transfers depending on controller capabilities. It also provides
generic SCSI features such as tagged command queueing and auto-request sense. This driver
is configured by default for a maximum of 446 outstanding commands per bus, 8 LUNs per
target and 64 tagged tasks per LUN. These numbers are not so much limited by design as they
are considered reasonable values for current SCSI technology. These values can be increased
by changing appropriate constants in driver header files (not recommended).

This driver supports the entire Symbios 53C8XX family of PCI SCSI controllers. It also
offers the advantage of architectural improvements available only with newer chips.

sym notably handles phase mismatch from SCRIPTS for the 53C896, 53C895A, and 53C1010 cores.
As a result, it guarantees that no more than 1 interrupt per IO completion is delivered to
the CPU, and that the SCRIPTS processor is never stalled waiting for CPU attention in normal
situations.

sym also uses LOAD/STORE SCRIPTS instructions for chips that support it. Only the early
810, 815 and 825 NCR chips do not support LOAD/STORE. Use of LOAD/STORE instead of MEMORY
MOVE allows SCRIPTS to access IO registers internal to the chip (no external PCI cycles).
As a result, the driver guarantees that no PCI self-mastering will occur for chips that
support LOAD/STORE.

LOAD/STORE instructions are also faster than MEMORY MOVE because they do not involve the
chip DMA FIFO and are coded on 2 DWORDs instead of 3.

For the early NCR 810, 815 and 825 chips, the driver uses a separate SCRIPTS set that uses
MEMORY MOVE instructions for data movements. This is because LOAD/STORE are not supported
by these chips.

HVD/LVD capable controllers (895, 895A, 896, and 897) report the actual bus mode in the
STEST4 chip IO registers. This feature allows the driver to safely probe against bus mode
and to set up the chip accordingly. By default the driver only supports HVD for these
chips. For other chips that can support HVD but not LVD, the driver has to probe
implementation dependent registers (GPIO) in order to detect HVD bus mode. Only HVD
implementations that conform with Symbios Logic recommendations can be detected by the
driver. When the SYM_SETUP_SCSI_DIFF kernel option is assigned a value of 1, the driver
will also probe against HVD for 825a, 875, 876 and 885 chips, assuming Symbios Logic
compatible implementation of HVD.

When the SYM_SETUP_PCI_PARITY is assigned a value of 0, the driver will not enable PCI
parity checking for 53C8XX devices. PCI parity checking should not be an option for PCI
SCSI controllers, but some systems have been reported to fail using 53C8XX chips, due to
spurious or permanent PCI parity errors detected. This option is supplied for convenience
but it is neither recommended nor supported.

The generic ncr(4) driver also supports SYM53C8XX based PCI SCSI controllers, except for the
SYM53C1010, which is only supported by the sym driver.

By default, when both the ncr(4) and sym drivers are configured, the sym driver takes
precedence over the ncr(4) driver. The user can indicate a balancing of chip types between
the two drivers by defining the SYM_SETUP_LP_PROBE_MAP kernel configuration option as
follows:

Bit Devices to be attached by ncr instead
0x01 53C810a, 53C860
0x02 53C825a, 53C875, 53C876, 53C885, 53C895
0x04 53C895a, 53C896, 53C897, 53C1510d
0x40 53C810, 53C815, 53C825

For example, if SYM_SETUP_LP_PROBE_MAP is supplied with the value 0x41, the ncr(4) driver
will attach to 53C810, 53C815, 53C825, 53C810a, and 53C860 based controllers, and the sym
driver will attach to all other 53C8XX based controllers.

When only the sym driver is configured, the SYM_SETUP_LP_PROBE_MAP option has no effect.
Thus, in this case, the sym driver will attach all 53C8XX based controllers present in the
system.

This driver offers other options that are not currently exported to the user. They are
defined and documented in the sym_conf.h driver file. Changing these options is not
recommended unless absolutely necessary. Some of these options are planned to be exported
through sysctl(3) or an equivalent mechanism in a future driver releases and therefore, no
compatibility is guaranteed.

At initialization, the driver tries to detect and read user settings from controller NVRAM.
The Symbios/Logic NVRAM layout and the Tekram NVRAM layout are currently supported. If the
reading of the NVRAM succeeds, the following settings are taken into account and reported to
CAM:

Host settings Symbios Tekram
SCSI parity checking Y N
Host SCSI ident Y Y
Verbose messages Y N
Scan targets hi-lo Y N
Avoid SCSI bus reset Y N

Device settings Symbios Tekram
Synchronous period Y Y
SCSI bus width Y Y
Queue tag enable Y Y
Number of tags NA Y
Disconnect enable Y Y
Scan at boot time Y N
Scan LUN Y N

Devices that are configured as disabled for 'scan' in the NVRAM are not reported to CAM at
system start-up. They can be discovered later using the ‘camcontrol rescan’ command.

The table below summarizes the main features and capabilities of the NCR/Symbios/LSI Logic
53C8XX family of PCI SCSI controllers.

Chip Sync Width SRAM PCI64 Supported
sym53c810 10MHz 8Bit N N Y
sym53c810a 10MHz 8Bit N N Y
sym53c815 10MHz 8Bit N N Y
sym53c825 10MHz 16Bit N N Y
sym53c825a 10MHz 16Bit 4KB N Y
sym53c860 20MHz 8Bit N N Y
sym53c875 20MHz 16Bit 4KB N Y
sym53c876 20MHz 16Bit 4KB N Y
sym53c885 20MHz 16Bit 4KB N Y
sym53c895 40MHz 16Bit 4KB N Y
sym53c895A 40MHz 16Bit 8KB N Y
sym53c896 40MHz 16Bit 8KB Y Y
sym53c897 40MHz 16Bit 8KB Y Y
sym53c1510D 40MHz 16Bit 4KB Y Y
sym53c1010 80MHz 16Bit 8KB Y Y

HARDWARE

     The sym driver provides support for the following Symbios/LSI Logic PCI SCSI controllers:

     •   53C810
     •   53C810A
     •   53C815
     •   53C825
     •   53C825A
     •   53C860
     •   53C875
     •   53C876
     •   53C895
     •   53C895A
     •   53C896
     •   53C897
     •   53C1000
     •   53C1000R
     •   53C1010-33
     •   53C1010-66
     •   53C1510D

     The SCSI controllers supported by sym can be either embedded on a motherboard, or on one of
     the following add-on boards:

     •   ASUS SC-200, SC-896
     •   Data Technology DTC3130 (all variants)
     •   DawiControl DC2976UW
     •   Diamond FirePort (all)
     •   NCR cards (all)
     •   Symbios cards (all)
     •   Tekram DC390W, 390U, 390F, 390U2B, 390U2W, 390U3D, and 390U3W
     •   Tyan S1365

MISC

     The DEC KZPCA-AA is a rebadged SYM8952U.

HISTORY

     The sym driver appeared in FreeBSD 4.0.

AUTHORS

     The sym driver was written by Gerard Roudier and is derived from the Linux sym53c8xx driver
     from the same author.  The sym53c8xx driver is derived from the ncr53c8xx driver, which was
     ported from the FreeBSD ncr(4) driver to Linux-1.2.13.  The original ncr(4) driver was
     written for 386BSD and FreeBSD by Wolfgang Stanglmeier and Stefan Esser.

BUGS

     No known bugs.