Ubuntu Manpage: badblocks - search a device for bad blocks

Provided by: e2fsprogs_1.45.5-2ubuntu1.2_amd64

NAME

       badblocks - search a device for bad blocks

SYNOPSIS

       badblocks  [  -svwnfBX  ]  [  -b  block_size  ]  [  -c  blocks_at_once  ]  [  -d read_delay_factor ] [ -e
       max_bad_blocks ] [ -i input_file ] [ -o output_file ] [ -p num_passes ] [  -t  test_pattern  ]  device  [
       last_block ] [ first_block ]

DESCRIPTION

       badblocks is used to search for bad blocks on a device (usually a disk partition).  device is the special
       file  corresponding  to the device (e.g /dev/hdc1).  last_block is the last block to be checked; if it is
       not specified, the last block on the device is used as a default.  first_block is an  optional  parameter
       specifying the starting block number for the test, which allows the testing to start in the middle of the
       disk.  If it is not specified the first block on the disk is used as a default.

       Important  note:  If  the  output of badblocks is going to be fed to the e2fsck or mke2fs programs, it is
       important that the block size is properly specified, since the block numbers which are generated are very
       dependent on the block size in use by the filesystem.  For this reason, it is strongly  recommended  that
       users not run badblocks directly, but rather use the -c option of the e2fsck and mke2fs programs.

OPTIONS

-b block_size
Specify the size of blocks in bytes. The default is 1024.

-c number of blocks
is the number of blocks which are tested at a time. The default is 64.

-d read delay factor
This parameter, if passed and non-zero, will cause bad blocks to sleep between reads if there were
no errors encountered in the read operation; the delay will be calculated as a percentage of the
time it took for the read operation to be performed. In other words, a value of 100 will cause
each read to be delayed by the amount the previous read took, and a value of 200 by twice the
amount.

-e max bad block count
Specify a maximum number of bad blocks before aborting the test. The default is 0, meaning the
test will continue until the end of the test range is reached.

-f Normally, badblocks will refuse to do a read/write or a non-destructive test on a device which is
mounted, since either can cause the system to potentially crash and/or damage the filesystem even
if it is mounted read-only. This can be overridden using the -f flag, but should almost never be
used --- if you think you're smarter than the badblocks program, you almost certainly aren't. The
only time when this option might be safe to use is if the /etc/mtab file is incorrect, and the
device really isn't mounted.

-i input_file
Read a list of already existing known bad blocks. Badblocks will skip testing these blocks since
they are known to be bad. If input_file is specified as "-", the list will be read from the
standard input. Blocks listed in this list will be omitted from the list of new bad blocks
produced on the standard output or in the output file. The -b option of dumpe2fs(8) can be used
to retrieve the list of blocks currently marked bad on an existing filesystem, in a format
suitable for use with this option.

-n Use non-destructive read-write mode. By default only a non-destructive read-only test is done.
This option must not be combined with the -w option, as they are mutually exclusive.

-o output_file
Write the list of bad blocks to the specified file. Without this option, badblocks displays the
list on its standard output. The format of this file is suitable for use by the -l option in
e2fsck(8) or mke2fs(8).

-p num_passes
Repeat scanning the disk until there are no new blocks discovered in num_passes consecutive scans
of the disk. Default is 0, meaning badblocks will exit after the first pass.

-s Show the progress of the scan by writing out rough percentage completion of the current badblocks
pass over the disk. Note that badblocks may do multiple test passes over the disk, in particular
if the -p or -w option is requested by the user.

-t test_pattern
Specify a test pattern to be read (and written) to disk blocks. The test_pattern may either be a
numeric value between 0 and ULONG_MAX-1 inclusive, or the word "random", which specifies that the
block should be filled with a random bit pattern. For read/write (-w) and non-destructive (-n)
modes, one or more test patterns may be specified by specifying the -t option for each test
pattern desired. For read-only mode only a single pattern may be specified and it may not be
"random". Read-only testing with a pattern assumes that the specified pattern has previously been
written to the disk - if not, large numbers of blocks will fail verification. If multiple
patterns are specified then all blocks will be tested with one pattern before proceeding to the
next pattern.

-v Verbose mode. Will write the number of read errors, write errors and data- corruptions to stderr.

-w Use write-mode test. With this option, badblocks scans for bad blocks by writing some patterns
(0xaa, 0x55, 0xff, 0x00) on every block of the device, reading every block and comparing the
contents. This option may not be combined with the -n option, as they are mutually exclusive.

-B Use buffered I/O and do not use Direct I/O, even if it is available.

-X Internal flag only to be used by e2fsck(8) and mke2fs(8). It bypasses the exclusive mode in-use
device safety check.

WARNING

       Never use the -w option on a device containing an existing file system.  This option erases data!  If you
       want  to  do write-mode testing on an existing file system, use the -n option instead.  It is slower, but
       it will preserve your data.

       The -e option will cause badblocks to output a possibly incomplete list of bad blocks.  Therefore  it  is
       recommended  to  use it only when one wants to know if there are any bad blocks at all on the device, and
       not when the list of bad blocks is wanted.

AUTHOR

       badblocks  was  written  by  Remy  Card  <Remy.Card@linux.org>.   Current  maintainer  is  Theodore  Ts'o
       <tytso@alum.mit.edu>.      Non-destructive    read/write    test    implemented    by    David    Beattie
       <dbeattie@softhome.net>.

AVAILABILITY

       badblocks is part of the e2fsprogs package and is available from http://e2fsprogs.sourceforge.net.