Provided by: sg3-utils_1.44-1ubuntu2_amd64 
NAME
sg_readcap - send SCSI READ CAPACITY command
SYNOPSIS
sg_readcap [--16] [--brief] [--help] [--hex] [--lba=LBA] [--long] [--pmi] [--raw]
[--readonly] [--verbose] [--version] DEVICE
sg_readcap [-16] [-b] [-h] [-H] [-lba=LBA] [-pmi] [-r] [-R] [-v] [-V] DEVICE
DESCRIPTION
The normal action of the SCSI READ CAPACITY command is to fetch the number of blocks (and
block size) from the DEVICE.
The SCSI READ CAPACITY command (both 10 and 16 byte cdbs) actually yield the block address
of the last block and the block size. The number of blocks is thus one plus the block
address of the last block (as blocks are counted origin zero (i.e. starting at block
zero)). This is the source of many "off by one" errors.
The READ CAPACITY(16) response provides additional information not found in the READ
CAPACITY(10) response. This includes protection and logical block provisioning
information, plus the number of logical blocks per physical block. So even though the
media size may not exceed what READ CAPACITY(10) can show, it may still be useful to
examine the response to READ CAPACITY(16). Sadly there are horrible SCSI command set
implementations in the wild that crash when the READ CAPACITY(16) command is sent to them.
Device capacity is the product of the number of blocks by the block size. This utility
outputs this figure in bytes, MiB (1048576 bytes per MiB), GB (1000000000 bytes per GB)
and, if large enough, TB (1000 GB).
If sg_readcap is called without the --long option then the 10 byte cdb version (i.e. READ
CAPACITY (10)) is sent to the DEVICE. If the number of blocks in the response is reported
as 0xffffffff (i.e. (2**32 - 1) ) and the --hex option has not been given, then READ
CAPACITY (16) is called and its response is output.
This utility supports two command line syntaxes, the preferred one is shown first in the
synopsis and explained in this section. A later section on the old command line syntax
outlines the second group of options.
OPTIONS
Arguments to long options are mandatory for short options as well. The options are
arranged in alphabetical order based on the long option name.
--16 Use the 16 byte cdb variant of the READ CAPACITY command. See the '--long' option.
-b, --brief outputs two hex numbers (prefixed with '0x' and space separated) to
stdout. The first number is the maximum number of blocks on the device (which is
one plus the lba of the last accessible block). The second number is the size in
bytes of each block. If the operation fails then "0x0 0x0" is written to stdout.
-h, --help
print out the usage message then exit.
-H, --hex
output the response to the READ CAPACITY command (either the 10 or 16 byte cdb
variant) in ASCII hexadecimal on stdout.
-L, --lba=LBA
used in conjunction with --pmi option. This variant of READ CAPACITY will yield the
last block address after LBA prior to a delay. For a disk, given a LBA it yields
the highest numbered block on the same cylinder (i.e. before the heads need to
move). LBA is assumed to be decimal unless prefixed by "0x" or it has a trailing
"h". Defaults to 0. This option was made obsolete in SBC-3 revision 26.
-l, --long
Use the 16 byte cdb variant of the READ CAPACITY command. The default action is to
use the 10 byte cdb variant which limits the maximum block address to (2**32 - 2).
When a 10 byte cdb READ CAPACITY command is used on a device whose size is too
large then a last block address of 0xffffffff is returned (if the device complies
with SBC-2 or later).
-O, --old
Switch to older style options. Please use as first option.
-p, --pmi
partial medium indicator: for finding the next block address prior to some delay
(e.g. head movement). In the absence of this option, the total number of blocks and
the block size of the device are output. Used in conjunction with the --lba=LBA
option. This option was made obsolete in SBC-3 revision 26.
-r, --raw
output response in binary to stdout.
-R, --readonly
open the DEVICE read-only (e.g. in Unix with the O_RDONLY flag). The default for
READ CAPACITY(16) is to open it read-write. The default for READ CAPACITY(10) is to
open it read-only so this option does not change anything for this case.
-v, --verbose
increase level of verbosity. Can be used multiple times.
-V, --version
outputs version string then exits.
NOTES
The response to READ CAPACITY(16) contains a LBPRZ bit in the SBC-3 standard (ANSI INCITS
514-2014). There was also a LBPRZ bit with the same meaning in the Logical block
provisioning VPD page (0xb2). Then somewhat confusingly T10 expanded the LBPRZ bit to a 3
bit field in SBC-4 draft revision 7, but only in the LB provisioning VPD page. The reason
for the expansion was to report a new "provisioning initialization pattern" state (when an
unmapped logical block is read). The new state has been assigned LBPRZ=2 in the VPD page
and it re-uses LBPRZ=0 in the READ CAPACITY(16) response. LBPRZ=1 retains the same meaning
for both variants, namely that a block of zeroes will be returned when an unmapped logical
block is read.
EXIT STATUS
The exit status of sg_readcap is 0 when it is successful. Otherwise see the sg3_utils(8)
man page.
OLDER COMMAND LINE OPTIONS
The options in this section were the only ones available prior to sg3_utils version 1.23 .
Since then this utility defaults to the newer command line options which can be overridden
by using --old (or -O) as the first option. See the ENVIRONMENT VARIABLES section for
another way to force the use of these older command line options.
-16 Use the 16 byte cdb variant of the READ CAPACITY command. Equivalent to --long in
the main description.
-b utility outputs two hex numbers (prefixed with '0x' and space separated) to stdout.
The first number is the maximum number of blocks on the device (which is one plus
the lba of the last accessible block). The second number is the size of each block.
If the operation fails then "0x0 0x0" is written to stdout. Equivalent to --brief
in the main description.
-h output the usage message then exit. Giving the -? option also outputs the usage
message then exits.
-H output the response to the READ CAPACITY command (either the 10 or 16 byte cdb
variant) in ASCII hexadecimal on stdout.
-lba=LBA
used in conjunction with -pmi option. This variant of READ CAPACITY will yield the
last block address after LBA prior to a delay. Equivalent to --lba=LBA in the main
description.
-N, --new
Switch to the newer style options.
-pmi partial medium indicator: for finding the next block address prior to some delay
(e.g. head movement). In the absence of this switch, the total number of blocks and
the block size of the device are output. Equivalent to --pmi in the main
description.
-r output response in binary (to stdout).
-R Equivalent to --readonly in the main description.
-v verbose: print out cdb of issued commands prior to execution. '-vv' and '-vvv' are
also accepted yielding greater verbosity.
-V outputs version string then exits.
ENVIRONMENT VARIABLES
Since sg3_utils version 1.23 the environment variable SG3_UTILS_OLD_OPTS can be given.
When it is present this utility will expect the older command line options. So the
presence of this environment variable is equivalent to using --old (or -O) as the first
command line option.
AUTHORS
Written by Douglas Gilbert
COPYRIGHT
Copyright © 1999-2018 Douglas Gilbert
This software is distributed under the GPL version 2. There is NO warranty; not even for
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sg_inq(sg3_utils)