Provided by: netplan.io_0.103-0ubuntu7_amd64 
NAME
netplan - YAML network configuration abstraction for various backends
SYNOPSIS
netplan [ COMMAND | help ]
COMMANDS
See netplan help for a list of available commands on this system.
DESCRIPTION
Introduction
Distribution installers, cloud instantiation, image builds for particular devices, or any
other way to deploy an operating system put its desired network configuration into YAML
configuration file(s). During early boot, the netplan “network renderer” runs which reads
/{lib,etc,run}/netplan/*.yaml and writes configuration to /run to hand off control of
devices to the specified networking daemon.
• Configured devices get handled by systemd-networkd by default, unless explicitly marked
as managed by a specific renderer (NetworkManager)
• Devices not covered by the network config do not get touched at all.
• Usable in initramfs (few dependencies and fast)
• No persistent generated config, only original YAML config
• Parser supports multiple config files to allow applications like libvirt or lxd to
package up expected network config (virbr0, lxdbr0), or to change the global default
policy to use NetworkManager for everything.
• Retains the flexibility to change backends/policy later or adjust to removing
NetworkManager, as generated configuration is ephemeral.
General structure
netplan’s configuration files use the YAML (http://yaml.org/spec/1.1/current.html) format.
All /{lib,etc,run}/netplan/*.yaml are considered. Lexicographically later files
(regardless of in which directory they are) amend (new mapping keys) or override (same
mapping keys) previous ones. A file in /run/netplan completely shadows a file with same
name in /etc/netplan, and a file in either of those directories shadows a file with the
same name in /lib/netplan.
The top-level node in a netplan configuration file is a network: mapping that contains
version: 2 (the YAML currently being used by curtin, MaaS, etc. is version 1), and then
device definitions grouped by their type, such as ethernets:, modems:, wifis:, or
bridges:. These are the types that our renderer can understand and are supported by our
backends.
Each type block contains device definitions as a map where the keys (called “configuration
IDs”) are defined as below.
Device configuration IDs
The key names below the per-device-type definition maps (like ethernets:) are called
“ID”s. They must be unique throughout the entire set of configuration files. Their
primary purpose is to serve as anchor names for composite devices, for example to
enumerate the members of a bridge that is currently being defined.
(Since 0.97) If an interface is defined with an ID in a configuration file; it will be
brought up by the applicable renderer. To not have netplan touch an interface at all, it
should be completely omitted from the netplan configuration files.
There are two physically/structurally different classes of device definitions, and the ID
field has a different interpretation for each:
Physical devices
(Examples: ethernet, modem, wifi) These can dynamically come and go between reboots
and even during runtime (hotplugging). In the generic case, they can be selected
by match: rules on desired properties, such as name/name pattern, MAC address,
driver, or device paths. In general these will match any number of devices (unless
they refer to properties which are unique such as the full path or MAC address), so
without further knowledge about the hardware these will always be considered as a
group.
It is valid to specify no match rules at all, in which case the ID field is simply
the interface name to be matched. This is mostly useful if you want to keep simple
cases simple, and it’s how network device configuration has been done for a long
time.
If there are match: rules, then the ID field is a purely opaque name which is only
being used for references from definitions of compound devices in the config.
Virtual devices
(Examples: veth, bridge, bond) These are fully under the control of the config
file(s) and the network stack. I. e. these devices are being created instead of
matched. Thus match: and set-name: are not applicable for these, and the ID field
is the name of the created virtual device.
Common properties for physical device types
match (mapping)
This selects a subset of available physical devices by various hardware properties.
The following configuration will then apply to all matching devices, as soon as
they appear. All specified properties must match.
name (scalar)
Current interface name. Globs are supported, and the primary use case for
matching on names, as selecting one fixed name can be more easily achieved
with having no match: at all and just using the ID (see above).
(NetworkManager: as of v1.14.0)
macaddress (scalar)
Device’s MAC address in the form “XX:XX:XX:XX:XX:XX”. Globs are not
allowed.
driver (scalar)
Kernel driver name, corresponding to the DRIVER udev property. Globs are
supported. Matching on driver is only supported with networkd.
Examples:
• all cards on second PCI bus:
match:
name: enp2*
• fixed MAC address:
match:
macaddress: 11:22:33:AA:BB:FF
• first card of driver ixgbe:
match:
driver: ixgbe
name: en*s0
set-name (scalar)
When matching on unique properties such as path or MAC, or with additional
assumptions such as “there will only ever be one wifi device”, match rules can be
written so that they only match one device. Then this property can be used to give
that device a more specific/desirable/nicer name than the default from udev’s
ifnames. Any additional device that satisfies the match rules will then fail to
get renamed and keep the original kernel name (and dmesg will show an error).
wakeonlan (bool)
Enable wake on LAN. Off by default.
Note: This will not work reliably for devices matched by name only and rendered by
networkd, due to interactions with device renaming in udev. Match devices by MAC
when setting wake on LAN.
emit-lldp (bool) – since 0.99
(networkd backend only) Whether to emit LLDP packets. Off by default.
openvswitch (mapping) – since 0.100
This provides additional configuration for the network device for openvswitch. If
openvswitch is not available on the system, netplan treats the presence of
openvswitch configuration as an error.
Any supported network device that is declared with the openvswitch mapping (or any
bond/bridge that includes an interface with an openvswitch configuration) will be
created in openvswitch instead of the defined renderer. In the case of a vlan
definition declared the same way, netplan will create a fake VLAN bridge in
openvswitch with the requested vlan properties.
external-ids (mapping) – since 0.100
Passed-through directly to OpenVSwitch
other-config (mapping) – since 0.100
Passed-through directly to OpenVSwitch
lacp (scalar) – since 0.100
Valid for bond interfaces. Accepts active, passive or off (the default).
fail-mode (scalar) – since 0.100
Valid for bridge interfaces. Accepts secure or standalone (the default).
mcast-snooping (bool) – since 0.100
Valid for bridge interfaces. False by default.
protocols (sequence of scalars) – since 0.100
Valid for bridge interfaces or the network section. List of protocols to be
used when negotiating a connection with the controller. Accepts OpenFlow10,
OpenFlow11, OpenFlow12, OpenFlow13, OpenFlow14, OpenFlow15 and OpenFlow16.
rstp (bool) – since 0.100
Valid for bridge interfaces. False by default.
controller (mapping) – since 0.100
Valid for bridge interfaces. Specify an external OpenFlow controller.
addresses (sequence of scalars)
Set the list of addresses to use for the controller targets. The
syntax of these addresses is as defined in ovs-vsctl(8). Example:
addresses: [tcp:127.0.0.1:6653, "ssl:[fe80::1234%eth0]:6653"]
connection-mode (scalar)
Set the connection mode for the controller. Supported options are
in-band and out-of-band. The default is in-band.
ports (sequence of sequence of scalars) – since 0.100
OpenvSwitch patch ports. Each port is declared as a pair of names which can
be referenced as interfaces in dependent virtual devices (bonds, bridges).
Example:
openvswitch:
ports:
- [patch0-1, patch1-0]
ssl (mapping) – since 0.100
Valid for global openvswitch settings. Options for configuring SSL server
endpoint for the switch.
ca-cert (scalar)
Path to a file containing the CA certificate to be used.
certificate (scalar)
Path to a file containing the server certificate.
private-key (scalar)
Path to a file containing the private key for the server.
Common properties for all device types
renderer (scalar)
Use the given networking backend for this definition. Currently supported are
networkd and NetworkManager. This property can be specified globally in network:,
for a device type (in e. g. ethernets:) or for a particular device definition.
Default is networkd.
(Since 0.99) The renderer property has one additional acceptable value for vlan
objects (i. e. defined in vlans:): sriov. If a vlan is defined with the sriov
renderer for an SR-IOV Virtual Function interface, this causes netplan to set up a
hardware VLAN filter for it. There can be only one defined per VF.
dhcp4 (bool)
Enable DHCP for IPv4. Off by default.
dhcp6 (bool)
Enable DHCP for IPv6. Off by default. This covers both stateless DHCP - where the
DHCP server supplies information like DNS nameservers but not the IP address - and
stateful DHCP, where the server provides both the address and the other
information.
If you are in an IPv6-only environment with completely stateless autoconfiguration
(SLAAC with RDNSS), this option can be set to cause the interface to be brought up.
(Setting accept-ra alone is not sufficient.) Autoconfiguration will still honour
the contents of the router advertisement and only use DHCP if requested in the RA.
Note that rdnssd(8) is required to use RDNSS with networkd. No extra software is
required for NetworkManager.
ipv6-mtu (scalar) – since 0.98
Set the IPv6 MTU (only supported with networkd backend). Note that needing to set
this is an unusual requirement.
Requires feature: ipv6-mtu
ipv6-privacy (bool)
Enable IPv6 Privacy Extensions (RFC 4941) for the specified interface, and prefer
temporary addresses. Defaults to false - no privacy extensions. There is
currently no way to have a private address but prefer the public address.
link-local (sequence of scalars)
Configure the link-local addresses to bring up. Valid options are `ipv4' and
`ipv6', which respectively allow enabling IPv4 and IPv6 link local addressing. If
this field is not defined, the default is to enable only IPv6 link-local addresses.
If the field is defined but configured as an empty set, IPv6 link-local addresses
are disabled as well as IPv4 link- local addresses.
This feature enables or disables link-local addresses for a protocol, but the
actual implementation differs per backend. On networkd, this directly changes the
behavior and may add an extra address on an interface. When using the
NetworkManager backend, enabling link-local has no effect if the interface also has
DHCP enabled.
Example to enable only IPv4 link-local: link-local: [ ipv4 ] Example to enable all
link-local addresses: link-local: [ ipv4, ipv6 ] Example to disable all link-local
addresses: link-local: [ ]
critical (bool)
Designate the connection as “critical to the system”, meaning that special care
will be taken by to not release the assigned IP when the daemon is restarted. (not
recognized by NetworkManager)
dhcp-identifier (scalar)
(networkd backend only) Sets the source of DHCPv4 client identifier. If mac is
specified, the MAC address of the link is used. If this option is omitted, or if
duid is specified, networkd will generate an RFC4361-compliant client identifier
for the interface by combining the link’s IAID and DUID.
dhcp4-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides
section below.
dhcp6-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides
section below.
accept-ra (bool)
Accept Router Advertisement that would have the kernel configure IPv6 by itself.
When enabled, accept Router Advertisements. When disabled, do not respond to
Router Advertisements. If unset use the host kernel default setting.
addresses (sequence of scalars and mappings)
Add static addresses to the interface in addition to the ones received through DHCP
or RA. Each sequence entry is in CIDR notation, i. e. of the form
addr/prefixlen. addr is an IPv4 or IPv6 address as recognized by inet_pton(3) and
prefixlen the number of bits of the subnet.
For virtual devices (bridges, bonds, vlan) if there is no address configured and
DHCP is disabled, the interface may still be brought online, but will not be
addressable from the network.
In addition to the addresses themselves one can specify configuration parameters as
mappings. Current supported options are:
lifetime (scalar) – since 0.100
Default: forever. This can be forever or 0 and corresponds to the
PreferredLifetime option in systemd-networkd’s Address section. Currently
supported on the networkd backend only.
label (scalar) – since 0.100
An IP address label, equivalent to the ip address label command. Currently
supported on the networkd backend only.
Example: addresses: [192.168.14.2/24, "2001:1::1/64"]
Example:
ethernets:
eth0:
addresses:
- 10.0.0.15/24:
lifetime: 0
label: "maas"
- "2001:1::1/64"
ipv6-address-generation (scalar) – since 0.99
Configure method for creating the address for use with RFC4862 IPv6 Stateless
Address Autoconfiguration (only supported with NetworkManager backend). Possible
values are eui64 or stable-privacy.
ipv6-address-token (scalar) – since 0.100
Define an IPv6 address token for creating a static interface identifier for IPv6
Stateless Address Autoconfiguration. This is mutually exclusive with ipv6-address-
generation.
gateway4, gateway6 (scalar)
Deprecated, see Default routes. Set default gateway for IPv4/6, for manual address
configuration. This requires setting addresses too. Gateway IPs must be in a form
recognized by inet_pton(3). There should only be a single gateway per IP address
family set in your global config, to make it unambiguous. If you need multiple
default routes, please define them via routing-policy.
Example for IPv4: gateway4: 172.16.0.1 Example for IPv6: gateway6: "2001:4::1"
nameservers (mapping)
Set DNS servers and search domains, for manual address configuration. There are
two supported fields: addresses: is a list of IPv4 or IPv6 addresses similar to
gateway*, and search: is a list of search domains.
Example:
ethernets:
id0:
[...]
nameservers:
search: [lab, home]
addresses: [8.8.8.8, "FEDC::1"]
macaddress (scalar)
Set the device’s MAC address. The MAC address must be in the form
“XX:XX:XX:XX:XX:XX”.
Note: This will not work reliably for devices matched by name only and rendered by
networkd, due to interactions with device renaming in udev. Match devices by MAC
when setting MAC addresses.
Example:
ethernets:
id0:
match:
macaddress: 52:54:00:6b:3c:58
[...]
macaddress: 52:54:00:6b:3c:59
mtu (scalar)
Set the Maximum Transmission Unit for the interface. The default is 1500. Valid
values depend on your network interface.
Note: This will not work reliably for devices matched by name only and rendered by
networkd, due to interactions with device renaming in udev. Match devices by MAC
when setting MTU.
optional (bool)
An optional device is not required for booting. Normally, networkd will wait some
time for device to become configured before proceeding with booting. However, if a
device is marked as optional, networkd will not wait for it. This is only
supported by networkd, and the default is false.
Example:
ethernets:
eth7:
# this is plugged into a test network that is often
# down - don't wait for it to come up during boot.
dhcp4: true
optional: true
optional-addresses (sequence of scalars)
Specify types of addresses that are not required for a device to be considered
online. This changes the behavior of backends at boot time to avoid waiting for
addresses that are marked optional, and thus consider the interface as “usable”
sooner. This does not disable these addresses, which will be brought up anyway.
Example:
ethernets:
eth7:
dhcp4: true
dhcp6: true
optional-addresses: [ ipv4-ll, dhcp6 ]
activation-mode (scalar) – since 0.103
Allows specifying the management policy of the selected interface. By default,
netplan brings up any configured interface if possible. Using the activation-mode
setting users can override that behavior by either specifying manual, to hand over
control over the interface state to the administrator or (for networkd backend
only) off to force the link in a down state at all times. Any interface with
activation-mode defined is implicitly considered optional. Supported officially as
of networkd v248+.
Example:
ethernets:
eth1:
# this interface will not be put into an UP state automatically
dhcp4: true
activation-mode: manual
routes (sequence of mappings)
Configure static routing for the device; see the Routing section below.
routing-policy (sequence of mappings)
Configure policy routing for the device; see the Routing section below.
DHCP Overrides
Several DHCP behavior overrides are available. Most currently only have any effect when
using the networkd backend, with the exception of use-routes and route-metric.
Overrides only have an effect if the corresponding dhcp4 or dhcp6 is set to true.
If both dhcp4 and dhcp6 are true, the networkd backend requires that dhcp4-overrides and
dhcp6-overrides contain the same keys and values. If the values do not match, an error
will be shown and the network configuration will not be applied.
When using the NetworkManager backend, different values may be specified for
dhcp4-overrides and dhcp6-overrides, and will be applied to the DHCP client processes as
specified in the netplan YAML.
dhcp4-overrides, dhcp6-overrides (mapping)
The dhcp4-overrides and dhcp6-overrides mappings override the default DHCP
behavior.
use-dns (bool)
Default: true. When true, the DNS servers received from the DHCP server
will be used and take precedence over any statically configured ones.
Currently only has an effect on the networkd backend.
use-ntp (bool)
Default: true. When true, the NTP servers received from the DHCP server
will be used by systemd-timesyncd and take precedence over any statically
configured ones. Currently only has an effect on the networkd backend.
send-hostname (bool)
Default: true. When true, the machine’s hostname will be sent to the DHCP
server. Currently only has an effect on the networkd backend.
use-hostname (bool)
Default: true. When true, the hostname received from the DHCP server will
be set as the transient hostname of the system. Currently only has an
effect on the networkd backend.
use-mtu (bool)
Default: true. When true, the MTU received from the DHCP server will be set
as the MTU of the network interface. When false, the MTU advertised by the
DHCP server will be ignored. Currently only has an effect on the networkd
backend.
hostname (scalar)
Use this value for the hostname which is sent to the DHCP server, instead of
machine’s hostname. Currently only has an effect on the networkd backend.
use-routes (bool)
Default: true. When true, the routes received from the DHCP server will be
installed in the routing table normally. When set to false, routes from the
DHCP server will be ignored: in this case, the user is responsible for
adding static routes if necessary for correct network operation. This
allows users to avoid installing a default gateway for interfaces configured
via DHCP. Available for both the networkd and NetworkManager backends.
route-metric (scalar)
Use this value for default metric for automatically-added routes. Use this
to prioritize routes for devices by setting a lower metric on a preferred
interface. Available for both the networkd and NetworkManager backends.
use-domains (scalar) – since 0.98
Takes a boolean, or the special value “route”. When true, the domain name
received from the DHCP server will be used as DNS search domain over this
link, similar to the effect of the Domains= setting. If set to “route”, the
domain name received from the DHCP server will be used for routing DNS
queries only, but not for searching, similar to the effect of the Domains=
setting when the argument is prefixed with “~”.
Requires feature: dhcp-use-domains
Routing
Complex routing is possible with netplan. Standard static routes as well as policy
routing using routing tables are supported via the networkd backend.
These options are available for all types of interfaces.
Default routes
The most common need for routing concerns the definition of default routes to reach the
wider Internet. Those default routes can only defined once per IP family and routing
table. A typical example would look like the following:
eth0:
[...]
routes:
- to: default # could be 0/0 or 0.0.0.0/0 optionally
via: 10.0.0.1
metric: 100
on-link: true
- to: default # could be ::/0 optionally
via: cf02:de:ad:be:ef::2
eth1:
[...]
routes:
- to: default
via: 172.134.67.1
metric: 100
on-link: true
table: 76 # Not on the main routing table, does not conflict with the eth0 default route
routes (mapping)
The routes block defines standard static routes for an interface. At least to and
via must be specified.
For from, to, and via, both IPv4 and IPv6 addresses are recognized, and must be in
the form addr/prefixlen or addr.
from (scalar)
Set a source IP address for traffic going through the route.
(NetworkManager: as of v1.8.0)
to (scalar)
Destination address for the route.
via (scalar)
Address to the gateway to use for this route.
on-link (bool)
When set to “true”, specifies that the route is directly connected to the
interface. (NetworkManager: as of v1.12.0 for IPv4 and v1.18.0 for IPv6)
metric (scalar)
The relative priority of the route. Must be a positive integer value.
type (scalar)
The type of route. Valid options are “unicast” (default), “unreachable”,
“blackhole” or “prohibit”.
scope (scalar)
The route scope, how wide-ranging it is to the network. Possible values are
“global”, “link”, or “host”. NetworkManager does not support setting a
scope.
table (scalar)
The table number to use for the route. In some scenarios, it may be useful
to set routes in a separate routing table. It may also be used to refer to
routing policy rules which also accept a table parameter. Allowed values
are positive integers starting from 1. Some values are already in use to
refer to specific routing tables: see /etc/iproute2/rt_tables.
(NetworkManager: as of v1.10.0)
mtu (scalar) – since 0.101
The MTU to be used for the route, in bytes. Must be a positive integer
value.
congestion-window (scalar) – since 0.102
The congestion window to be used for the route, represented by number of
segments. Must be a positive integer value.
advertised-receive-window (scalar) – since 0.102
The receive window to be advertised for the route, represented by number of
segments. Must be a positive integer value.
routing-policy (mapping)
The routing-policy block defines extra routing policy for a network, where traffic
may be handled specially based on the source IP, firewall marking, etc.
For from, to, both IPv4 and IPv6 addresses are recognized, and must be in the form
addr/prefixlen or addr.
from (scalar)
Set a source IP address to match traffic for this policy rule.
to (scalar)
Match on traffic going to the specified destination.
table (scalar)
The table number to match for the route. In some scenarios, it may be
useful to set routes in a separate routing table. It may also be used to
refer to routes which also accept a table parameter. Allowed values are
positive integers starting from 1. Some values are already in use to refer
to specific routing tables: see /etc/iproute2/rt_tables.
priority (scalar)
Specify a priority for the routing policy rule, to influence the order in
which routing rules are processed. A higher number means lower priority:
rules are processed in order by increasing priority number.
mark (scalar)
Have this routing policy rule match on traffic that has been marked by the
iptables firewall with this value. Allowed values are positive integers
starting from 1.
type-of-service (scalar)
Match this policy rule based on the type of service number applied to the
traffic.
Authentication
Netplan supports advanced authentication settings for ethernet and wifi interfaces, as
well as individual wifi networks, by means of the auth block.
auth (mapping)
Specifies authentication settings for a device of type ethernets:, or an access-
points: entry on a wifis: device.
The auth block supports the following properties:
key-management (scalar)
The supported key management modes are none (no key management); psk (WPA
with pre-shared key, common for home wifi); eap (WPA with EAP, common for
enterprise wifi); and 802.1x (used primarily for wired Ethernet
connections).
password (scalar)
The password string for EAP, or the pre-shared key for WPA-PSK.
The following properties can be used if key-management is eap or 802.1x:
method (scalar)
The EAP method to use. The supported EAP methods are tls (TLS), peap
(Protected EAP), and ttls (Tunneled TLS).
identity (scalar)
The identity to use for EAP.
anonymous-identity (scalar)
The identity to pass over the unencrypted channel if the chosen EAP method
supports passing a different tunnelled identity.
ca-certificate (scalar)
Path to a file with one or more trusted certificate authority (CA)
certificates.
client-certificate (scalar)
Path to a file containing the certificate to be used by the client during
authentication.
client-key (scalar)
Path to a file containing the private key corresponding to client-
certificate.
client-key-password (scalar)
Password to use to decrypt the private key specified in client-key if it is
encrypted.
phase2-auth (scalar) – since 0.99
Phase 2 authentication mechanism.
Properties for device type ethernets:
Ethernet device definitions, beyond common ones described above, also support some
additional properties that can be used for SR-IOV devices.
link (scalar) – since 0.99
(SR-IOV devices only) The link property declares the device as a Virtual Function
of the selected Physical Function device, as identified by the given netplan id.
Example:
ethernets:
enp1: {...}
enp1s16f1:
link: enp1
virtual-function-count (scalar) – since 0.99
(SR-IOV devices only) In certain special cases VFs might need to be configured
outside of netplan. For such configurations virtual-function-count can be
optionally used to set an explicit number of Virtual Functions for the given
Physical Function. If unset, the default is to create only as many VFs as are
defined in the netplan configuration. This should be used for special cases only.
Requires feature: sriov
Properties for device type modems:
GSM/CDMA modem configuration is only supported for the NetworkManager backend. systemd-
networkd does not support modems.
Requires feature: modems
apn (scalar) – since 0.99
Set the carrier APN (Access Point Name). This can be omitted if auto-config is
enabled.
auto-config (bool) – since 0.99
Specify whether to try and autoconfigure the modem by doing a lookup of the carrier
against the Mobile Broadband Provider database. This may not work for all
carriers.
device-id (scalar) – since 0.99
Specify the device ID (as given by the WWAN management service) of the modem to
match. This can be found using mmcli.
network-id (scalar) – since 0.99
Specify the Network ID (GSM LAI format). If this is specified, the device will not
roam networks.
number (scalar) – since 0.99
The number to dial to establish the connection to the mobile broadband network.
(Deprecated for GSM)
password (scalar) – since 0.99
Specify the password used to authenticate with the carrier network. This can be
omitted if auto-config is enabled.
pin (scalar) – since 0.99
Specify the SIM PIN to allow it to operate if a PIN is set.
sim-id (scalar) – since 0.99
Specify the SIM unique identifier (as given by the WWAN management service) which
this connection applies to. If given, the connection will apply to any device also
allowed by device-id which contains a SIM card matching the given identifier.
sim-operator-id (scalar) – since 0.99
Specify the MCC/MNC string (such as “310260” or “21601”) which identifies the
carrier that this connection should apply to. If given, the connection will apply
to any device also allowed by device-id and sim-id which contains a SIM card
provisioned by the given operator.
username (scalar) – since 0.99
Specify the username used to authentiate with the carrier network. This can be
omitted if auto-config is enabled.
Properties for device type wifis:
Note that systemd-networkd does not natively support wifi, so you need wpasupplicant
installed if you let the networkd renderer handle wifi.
access-points (mapping)
This provides pre-configured connections to NetworkManager. Note that users can of
course select other access points/SSIDs. The keys of the mapping are the SSIDs,
and the values are mappings with the following supported properties:
password (scalar)
Enable WPA2 authentication and set the passphrase for it. If neither this
nor an auth block are given, the network is assumed to be open. The setting
password: "S3kr1t"
is equivalent to
auth:
key-management: psk
password: "S3kr1t"
mode (scalar)
Possible access point modes are infrastructure (the default), ap (create an
access point to which other devices can connect), and adhoc (peer to peer
networks without a central access point). ap is only supported with
NetworkManager.
bssid (scalar) – since 0.99
If specified, directs the device to only associate with the given access
point.
band (scalar) – since 0.99
Possible bands are 5GHz (for 5GHz 802.11a) and 2.4GHz (for 2.4GHz 802.11),
do not restrict the 802.11 frequency band of the network if unset (the
default).
channel (scalar) – since 0.99
Wireless channel to use for the Wi-Fi connection. Because channel numbers
overlap between bands, this property takes effect only if the band property
is also set.
hidden (bool) – since 0.100
Set to true to change the SSID scan technique for connecting to hidden WiFi
networks. Note this may have slower performance compared to false (the
default) when connecting to publicly broadcast SSIDs.
wakeonwlan (sequence of scalars) – since 0.99
This enables WakeOnWLan on supported devices. Not all drivers support all options.
May be any combination of any, disconnect, magic_pkt, gtk_rekey_failure,
eap_identity_req, four_way_handshake, rfkill_release or tcp (NetworkManager only).
Or the exclusive default flag (the default).
Properties for device type bridges:
interfaces (sequence of scalars)
All devices matching this ID list will be added to the bridge. This may be an
empty list, in which case the bridge will be brought online with no member
interfaces.
Example:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bridges:
br0:
interfaces: [switchports]
parameters (mapping)
Customization parameters for special bridging options. Time intervals may need to
be expressed as a number of seconds or milliseconds: the default value type is
specified below. If necessary, time intervals can be qualified using a time suffix
(such as “s” for seconds, “ms” for milliseconds) to allow for more control over its
behavior.
ageing-time (scalar)
Set the period of time to keep a MAC address in the forwarding database
after a packet is received. This maps to the AgeingTimeSec= property when
the networkd renderer is used. If no time suffix is specified, the value
will be interpreted as seconds.
priority (scalar)
Set the priority value for the bridge. This value should be a number
between 0 and 65535. Lower values mean higher priority. The bridge with
the higher priority will be elected as the root bridge.
port-priority (scalar)
Set the port priority to . The priority value is a number between 0 and 63.
This metric is used in the designated port and root port selection
algorithms.
forward-delay (scalar)
Specify the period of time the bridge will remain in Listening and Learning
states before getting to the Forwarding state. This field maps to the
ForwardDelaySec= property for the networkd renderer. If no time suffix is
specified, the value will be interpreted as seconds.
hello-time (scalar)
Specify the interval between two hello packets being sent out from the root
and designated bridges. Hello packets communicate information about the
network topology. When the networkd renderer is used, this maps to the
HelloTimeSec= property. If no time suffix is specified, the value will be
interpreted as seconds.
max-age (scalar)
Set the maximum age of a hello packet. If the last hello packet is older
than that value, the bridge will attempt to become the root bridge. This
maps to the MaxAgeSec= property when the networkd renderer is used. If no
time suffix is specified, the value will be interpreted as seconds.
path-cost (scalar)
Set the cost of a path on the bridge. Faster interfaces should have a lower
cost. This allows a finer control on the network topology so that the
fastest paths are available whenever possible.
stp (bool)
Define whether the bridge should use Spanning Tree Protocol. The default
value is “true”, which means that Spanning Tree should be used.
Properties for device type bonds:
interfaces (sequence of scalars)
All devices matching this ID list will be added to the bond.
Example:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bonds:
bond0:
interfaces: [switchports]
parameters (mapping)
Customization parameters for special bonding options. Time intervals may need to
be expressed as a number of seconds or milliseconds: the default value type is
specified below. If necessary, time intervals can be qualified using a time suffix
(such as “s” for seconds, “ms” for milliseconds) to allow for more control over its
behavior.
mode (scalar)
Set the bonding mode used for the interfaces. The default is balance-rr
(round robin). Possible values are balance-rr, active-backup, balance-xor,
broadcast, 802.3ad, balance-tlb, and balance-alb. For OpenVSwitch active-
backup and the additional modes balance-tcp and balance-slb are supported.
lacp-rate (scalar)
Set the rate at which LACPDUs are transmitted. This is only useful in
802.3ad mode. Possible values are slow (30 seconds, default), and fast
(every second).
mii-monitor-interval (scalar)
Specifies the interval for MII monitoring (verifying if an interface of the
bond has carrier). The default is 0; which disables MII monitoring. This
is equivalent to the MIIMonitorSec= field for the networkd backend. If no
time suffix is specified, the value will be interpreted as milliseconds.
min-links (scalar)
The minimum number of links up in a bond to consider the bond interface to
be up.
transmit-hash-policy (scalar)
Specifies the transmit hash policy for the selection of slaves. This is
only useful in balance-xor, 802.3ad and balance-tlb modes. Possible values
are layer2, layer3+4, layer2+3, encap2+3, and encap3+4.
ad-select (scalar)
Set the aggregation selection mode. Possible values are stable, bandwidth,
and count. This option is only used in 802.3ad mode.
all-slaves-active (bool)
If the bond should drop duplicate frames received on inactive ports, set
this option to false. If they should be delivered, set this option to true.
The default value is false, and is the desirable behavior in most
situations.
arp-interval (scalar)
Set the interval value for how frequently ARP link monitoring should happen.
The default value is 0, which disables ARP monitoring. For the networkd
backend, this maps to the ARPIntervalSec= property. If no time suffix is
specified, the value will be interpreted as milliseconds.
arp-ip-targets (sequence of scalars)
IPs of other hosts on the link which should be sent ARP requests in order to
validate that a slave is up. This option is only used when arp-interval is
set to a value other than 0. At least one IP address must be given for ARP
link monitoring to function. Only IPv4 addresses are supported. You can
specify up to 16 IP addresses. The default value is an empty list.
arp-validate (scalar)
Configure how ARP replies are to be validated when using ARP link
monitoring. Possible values are none, active, backup, and all.
arp-all-targets (scalar)
Specify whether to use any ARP IP target being up as sufficient for a slave
to be considered up; or if all the targets must be up. This is only used
for active-backup mode when arp-validate is enabled. Possible values are
any and all.
up-delay (scalar)
Specify the delay before enabling a link once the link is physically up.
The default value is 0. This maps to the UpDelaySec= property for the
networkd renderer. This option is only valid for the miimon link monitor.
If no time suffix is specified, the value will be interpreted as
milliseconds.
down-delay (scalar)
Specify the delay before disabling a link once the link has been lost. The
default value is 0. This maps to the DownDelaySec= property for the
networkd renderer. This option is only valid for the miimon link monitor.
If no time suffix is specified, the value will be interpreted as
milliseconds.
fail-over-mac-policy (scalar)
Set whether to set all slaves to the same MAC address when adding them to
the bond, or how else the system should handle MAC addresses. The possible
values are none, active, and follow.
gratuitous-arp (scalar)
Specify how many ARP packets to send after failover. Once a link is up on a
new slave, a notification is sent and possibly repeated if this value is set
to a number greater than 1. The default value is 1 and valid values are
between 1 and 255. This only affects active-backup mode.
For historical reasons, the misspelling gratuitious-arp is also accepted and
has the same function.
packets-per-slave (scalar)
In balance-rr mode, specifies the number of packets to transmit on a slave
before switching to the next. When this value is set to 0, slaves are
chosen at random. Allowable values are between 0 and 65535. The default
value is 1. This setting is only used in balance-rr mode.
primary-reselect-policy (scalar)
Set the reselection policy for the primary slave. On failure of the active
slave, the system will use this policy to decide how the new active slave
will be chosen and how recovery will be handled. The possible values are
always, better, and failure.
resend-igmp (scalar)
In modes balance-rr, active-backup, balance-tlb and balance-alb, a failover
can switch IGMP traffic from one slave to another.
This parameter specifies how many IGMP membership reports are issued on a
failover event. Values range from 0 to 255. 0 disables sending membership
reports. Otherwise, the first membership report is sent on failover and
subsequent reports are sent at 200ms intervals.
learn-packet-interval (scalar)
Specify the interval between sending learning packets to each slave. The
value range is between 1 and 0x7fffffff. The default value is 1. This
option only affects balance-tlb and balance-alb modes. Using the networkd
renderer, this field maps to the LearnPacketIntervalSec= property. If no
time suffix is specified, the value will be interpreted as seconds.
primary (scalar)
Specify a device to be used as a primary slave, or preferred device to use
as a slave for the bond (ie. the preferred device to send data through),
whenever it is available. This only affects active-backup, balance-alb, and
balance-tlb modes.
Properties for device type tunnels:
Tunnels allow traffic to pass as if it was between systems on the same local network,
although systems may be far from each other but reachable via the Internet. They may be
used to support IPv6 traffic on a network where the ISP does not provide the service, or
to extend and “connect” separate local networks. Please see
https://en.wikipedia.org/wiki/Tunneling_protocol for more general information about
tunnels.
mode (scalar)
Defines the tunnel mode. Valid options are sit, gre, ip6gre, ipip, ipip6, ip6ip6,
vti, vti6 and wireguard. Additionally, the networkd backend also supports gretap
and ip6gretap modes. In addition, the NetworkManager backend supports isatap
tunnels.
local (scalar)
Defines the address of the local endpoint of the tunnel.
remote (scalar)
Defines the address of the remote endpoint of the tunnel.
ttl (scalar) – since 0.103
Defines the TTL of the tunnel.
key (scalar or mapping)
Define keys to use for the tunnel. The key can be a number or a dotted quad (an
IPv4 address). For wireguard it can be a base64-encoded private key or (as of
networkd v242+) an absolute path to a file, containing the private key (since
0.100). It is used for identification of IP transforms. This is only required for
vti and vti6 when using the networkd backend, and for gre or ip6gre tunnels when
using the NetworkManager backend.
This field may be used as a scalar (meaning that a single key is specified and to
be used for input, output and private key), or as a mapping, where you can further
specify input/output/private.
input (scalar)
The input key for the tunnel
output (scalar)
The output key for the tunnel
private (scalar) – since 0.100
A base64-encoded private key required for Wireguard tunnels. When the
systemd-networkd backend (v242+) is used, this can also be an absolute path
to a file containing the private key.
keys (scalar or mapping)
Alternate name for the key field. See above.
Examples:
tunnels:
tun0:
mode: gre
local: ...
remote: ...
keys:
input: 1234
output: 5678
tunnels:
tun0:
mode: vti6
local: ...
remote: ...
key: 59568549
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
shared: /path/to/shared.key
...
key: mNb7OIIXTdgW4khM7OFlzJ+UPs7lmcWHV7xjPgakMkQ=
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
...
keys:
private: /path/to/priv.key
Wireguard specific keys:
mark (scalar) – since 0.100
Firewall mark for outgoing WireGuard packets from this interface, optional.
port (scalar) – since 0.100
UDP port to listen at or auto. Optional, defaults to auto.
peers (sequence of mappings) – since 0.100
A list of peers, each having keys documented below.
Example:
tunnels:
wg0:
mode: wireguard
key: /path/to/private.key
mark: 42
port: 5182
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
allowed-ips: [0.0.0.0/0, "2001:fe:ad:de:ad:be:ef:1/24"]
keepalive: 23
endpoint: 1.2.3.4:5
- keys:
public: M9nt4YujIOmNrRmpIRTmYSfMdrpvE7u6WkG8FY8WjG4=
shared: /some/shared.key
allowed-ips: [10.10.10.20/24]
keepalive: 22
endpoint: 5.4.3.2:1
endpoint (scalar) – since 0.100
Remote endpoint IPv4/IPv6 address or a hostname, followed by a colon and a port
number.
allowed-ips (sequence of scalars) – since 0.100
A list of IP (v4 or v6) addresses with CIDR masks from which this peer is allowed
to send incoming traffic and to which outgoing traffic for this peer is directed.
The catch-all 0.0.0.0/0 may be specified for matching all IPv4 addresses, and ::/0
may be specified for matching all IPv6 addresses.
keepalive (scalar) – since 0.100
An interval in seconds, between 1 and 65535 inclusive, of how often to send an
authenticated empty packet to the peer for the purpose of keeping a stateful
firewall or NAT mapping valid persistently. Optional.
keys (mapping) – since 0.100
Define keys to use for the Wireguard peers.
This field can be used as a mapping, where you can further specify the public and
shared keys.
public (scalar) – since 0.100
A base64-encoded public key, required for Wireguard peers.
shared (scalar) – since 0.100
A base64-encoded preshared key. Optional for Wireguard peers. When the
systemd-networkd backend (v242+) is used, this can also be an absolute path
to a file containing the preshared key.
Properties for device type vlans:
id (scalar)
VLAN ID, a number between 0 and 4094.
link (scalar)
netplan ID of the underlying device definition on which this VLAN gets created.
Example:
ethernets:
eno1: {...}
vlans:
en-intra:
id: 1
link: eno1
dhcp4: yes
en-vpn:
id: 2
link: eno1
addresses: ...
Properties for device type nm-devices:
The nm-devices device type is for internal use only and should not be used in normal
configuration files. It enables a fallback mode for unsupported settings, using the
passthrough mapping.
Backend-specific configuration parameters
In addition to the other fields available to configure interfaces, some backends may
require to record some of their own parameters in netplan, especially if the netplan
definitions are generated automatically by the consumer of that backend. Currently, this
is only used with NetworkManager.
networkmanager (mapping) – since 0.99
Keeps the NetworkManager-specific configuration parameters used by the daemon to
recognize connections.
name (scalar) – since 0.99
Set the display name for the connection.
uuid (scalar) – since 0.99
Defines the UUID (unique identifier) for this connection, as generated by
NetworkManager itself.
stable-id (scalar) – since 0.99
Defines the stable ID (a different form of a connection name) used by
NetworkManager in case the name of the connection might otherwise change,
such as when sharing connections between users.
device (scalar) – since 0.99
Defines the interface name for which this connection applies.
passthrough (mapping) – since 0.102
Can be used as a fallback mechanism to missing keyfile settings.
Examples
Configure an ethernet device with networkd, identified by its name, and enable DHCP:
network:
version: 2
ethernets:
eno1:
dhcp4: true
This is an example of a static-configured interface with multiple IPv4 addresses and
multiple gateways with networkd, with equal route metric levels, and static DNS
nameservers (Google DNS for this example):
network:
version: 2
renderer: networkd
ethernets:
eno1:
addresses:
- 10.0.0.10/24
- 11.0.0.11/24
nameservers:
addresses:
- 8.8.8.8
- 8.8.4.4
routes:
- to: 0.0.0.0/0
via: 10.0.0.1
metric: 100
- to: 0.0.0.0/0
via: 11.0.0.1
metric: 100
This is a complex example which shows most available features:
network:
version: 2
# if specified, can only realistically have that value, as networkd cannot
# render wifi/3G.
renderer: NetworkManager
ethernets:
# opaque ID for physical interfaces, only referred to by other stanzas
id0:
match:
macaddress: 00:11:22:33:44:55
wakeonlan: true
dhcp4: true
addresses:
- 192.168.14.2/24
- 192.168.14.3/24
- "2001:1::1/64"
nameservers:
search: [foo.local, bar.local]
addresses: [8.8.8.8]
routes:
- to: default
via: 192.168.14.1
- to: default
via: "2001:1::2"
- to: 0.0.0.0/0
via: 11.0.0.1
table: 70
on-link: true
metric: 3
routing-policy:
- to: 10.0.0.0/8
from: 192.168.14.2/24
table: 70
priority: 100
- to: 20.0.0.0/8
from: 192.168.14.3/24
table: 70
priority: 50
# only networkd can render on-link routes and routing policies
renderer: networkd
lom:
match:
driver: ixgbe
# you are responsible for setting tight enough match rules
# that only match one device if you use set-name
set-name: lom1
dhcp6: true
switchports:
# all cards on second PCI bus unconfigured by
# themselves, will be added to br0 below
match:
name: enp2*
mtu: 1280
wifis:
all-wlans:
# useful on a system where you know there is
# only ever going to be one device
match: {}
access-points:
"Joe's home":
# mode defaults to "infrastructure" (client)
password: "s3kr1t"
# this creates an AP on wlp1s0 using hostapd
# no match rules, thus the ID is the interface name
wlp1s0:
access-points:
"guest":
mode: ap
# no WPA config implies default of open
bridges:
# the key name is the name for virtual (created) interfaces
# no match: and set-name: allowed
br0:
# IDs of the components; switchports expands into multiple interfaces
interfaces: [wlp1s0, switchports]
dhcp4: true
SEE ALSO
netplan-generate(8), netplan-apply(8), netplan-try(8), netplan-get(8), netplan-set(8),
netplan-dbus(8), systemd-networkd(8), NetworkManager(8)
AUTHORS
Mathieu Trudel-Lapierre (<cyphermox@ubuntu.com>); Martin Pitt (<martin.pitt@ubuntu.com>).
netplan(5)