Provided by: netplan.io_0.106.1-7ubuntu0.22.04.4_amd64 bug

NAME

       netplan - YAML network configuration abstraction for various backends

SYNOPSIS

       netplan [ COMMAND | help ]

COMMANDS

       See netplan help for a list of available commands on this system.

DESCRIPTION

   Introduction
       Distribution  installers,  cloud  instantiation, image builds for particular devices, or any other way to
       deploy an operating system put its desired network configuration into YAML configuration file(s).  During
       early  boot,  the  netplan  "network  renderer" runs which reads /{lib,etc,run}/netplan/*.yaml and writes
       configuration to /run to hand off control of devices to the specified networking daemon.

       • Configured devices get handled by systemd-networkd by default, unless explicitly marked as managed by a
         specific renderer (NetworkManager)

       • Devices not covered by the network config do not get touched at all.

       • Usable in initramfs (few dependencies and fast)

       • No persistent generated config, only original YAML config

       • Parser  supports multiple config files to allow applications like libvirt or lxd to package up expected
         network config (virbr0, lxdbr0), or to change the global  default  policy  to  use  NetworkManager  for
         everything.

       • Retains  the  flexibility  to  change  backends/policy  later  or adjust to removing NetworkManager, as
         generated configuration is ephemeral.

   General structure
       netplan's  configuration  files  use  the  YAML  (http://yaml.org/spec/1.1/current.html)   format.    All
       /{lib,etc,run}/netplan/*.yaml  are  considered.   Lexicographically  later  files (regardless of in which
       directory they are) amend (new mapping keys) or override (same mapping keys) previous ones.   A  file  in
       /run/netplan  completely  shadows  a  file  with same name in /etc/netplan, and a file in either of those
       directories shadows a file with the same name in /lib/netplan.

       The top-level node in a netplan configuration file is a network: mapping that contains  version:  2  (the
       YAML  currently  being  used by curtin, MaaS, etc.  is version 1), and then device definitions grouped by
       their type, such as ethernets:, modems:, wifis:, or bridges:.  These are the types that our renderer  can
       understand and are supported by our backends.

       Each  type  block  contains  device  definitions as a map where the keys (called "configuration IDs") are
       defined as below.

   Device configuration IDs
       The key names below the per-device-type definition maps (like ethernets:) are called "ID"s.  They must be
       unique  throughout  the  entire  set of configuration files.  Their primary purpose is to serve as anchor
       names for composite devices, for example to enumerate the members of a bridge  that  is  currently  being
       defined.

       (Since  0.97) If an interface is defined with an ID in a configuration file; it will be brought up by the
       applicable renderer.  To not have netplan touch an interface at all, it should be completely omitted from
       the netplan configuration files.

       There  are  two  physically/structurally  different classes of device definitions, and the ID field has a
       different interpretation for each:

       Physical devices

              (Examples: ethernet, modem, wifi) These can dynamically come  and  go  between  reboots  and  even
              during  runtime  (hot  plugging).   In  the  generic case, they can be selected by match: rules on
              desired properties, such as name/name pattern, MAC address, driver, or device paths.   In  general
              these  will  match any number of devices (unless they refer to properties which are unique such as
              the full path or MAC address), so without further knowledge about the hardware these  will  always
              be considered as a group.

              It  is  valid to specify no match rules at all, in which case the ID field is simply the interface
              name to be matched.  This is mostly useful if you want to keep simple cases simple, and  it's  how
              network device configuration has been done for a long time.

              If  there are match: rules, then the ID field is a purely opaque name which is only being used for
              references from definitions of compound devices in the config.

       Virtual devices

              (Examples: veth, bridge, bond, vrf) These are fully under the control of the  config  file(s)  and
              the  network  stack.  I.  e.  these devices are being created instead of matched.  Thus match: and
              set-name: are not applicable for these, and the ID field  is  the  name  of  the  created  virtual
              device.

   Top-level configuration structure
       The general structure of a Netplan YAML file is shown below.

              network:
                version: NUMBER
                renderer: STRING
                bonds: MAPPING
                bridges: MAPPING
                ethernets: MAPPING
                modems: MAPPING
                tunnels: MAPPING
                vlans: MAPPING
                vrfs: MAPPING
                wifis: MAPPING
                nm-devices: MAPPING

       • version (number)

                Defines  what  version  of  the  configuration  format  is used.  The only value supported is 2.
                Defaults to 2 if not defined.

       • renderer (scalar)

                Defines what network configuration tool will be used to set up your configuration.  Valid values
                are networkd and NetworkManager.  Defaults to networkd if not defined.

       • bonds (mapping)

                Creates and configures link aggregation (bonding) devices.

       • bridges (mapping)

                Creates and configures bridge devices.

       • ethernets (mapping)

                Configures physical Ethernet interfaces.

       • modems (mapping)

                Configures modems

       • tunnels (mapping)

                Creates and configures different types of virtual tunnels.

       • vlans (mapping)

                Creates and configures VLANs.

       • vrfs (mapping)

                Configures Virtual Routing and Forwarding (VRF) devices.

       • wifis (mapping)

                Configures physical Wifi interfaces as client, adhoc or access point.

       • nm-devices (mapping)

                nm-devices  are  used  in situations where Netplan doesn't support the connection type.  The raw
                configuration expected by NetworkManager can be defined and will be passed as  is  (passthrough)
                to the .nmconnection file.  Users will not normally use this type of device.

       All the properties for all the device types will be described in the next sections.

   Properties for physical device types
       These properties are used with physical devices such as Ethernet and Wifi network interfaces.

       Note:  Some options will not work reliably for devices matched by name only and rendered by networkd, due
       to interactions with device renaming in udev.  Match devices by MAC when setting options like:  wakeonlan
       or *-offload.

       • match (mapping)

                This  selects  a  subset  of  available  physical  devices  by various hardware properties.  The
                following configuration will then apply to all matching devices, as soon as  they  appear.   All
                specified properties must match.

         • name (scalar)

                  Current  interface name.  Globs are supported, and the primary use case for matching on names,
                  as selecting one fixed name can be more easily achieved with having no match: at all and  just
                  using the ID (see above).  (NetworkManager: as of v1.14.0)

         • macaddress (scalar)

                  Device's  6-byte  permanent  MAC  address  in  the  form  "XX:XX:XX:XX:XX:XX"  or 20 bytes for
                  InfiniBand devices (IPoIB).  Globs are not allowed.  This doesn't match virtual MAC  addresses
                  for veth, bridge, bond, vlan, ...

         • driver (scalar or sequence of scalars) – sequence since 0.104

                  Kernel  driver  name,  corresponding  to  the  DRIVER  udev  property.  A sequence of globs is
                  supported, any of which must match.  Matching on driver is only supported with networkd.

         Examples:

         • All cards on second PCI bus:

                  network:
                    ethernets:
                      myinterface:
                        match:
                          name: enp2*

         • Fixed MAC address:

                  network:
                    ethernets:
                      interface0:
                        match:
                          macaddress: 11:22:33:AA:BB:FF

         • First card of driver ixgbe:

                  network:
                    ethernets:
                      nic0:
                        match:
                          driver: ixgbe
                          name: en*s0

         • First card with a driver matching bcmgenet or smsc*:

                  network:
                    ethernets:
                      nic0:
                        match:
                          driver: ["bcmgenet", "smsc*"]
                          name: en*

       • set-name (scalar)

                When matching on unique properties such as path or MAC, or with additional assumptions  such  as
                "there  will  only  ever be one wifi device", match rules can be written so that they only match
                one device.  Then this property can be used to give that device a more  specific/desirable/nicer
                name than the default from udev's ifnames.  Any additional device that satisfies the match rules
                will then fail to get renamed and keep the original kernel name (and dmesg will show an error).

       • wakeonlan (bool)

                Enable wake on LAN.  Off by default.

       • emit-lldp (bool) – since 0.99

                (networkd backend only) Whether to emit LLDP packets.  Off by default.

       • receive-checksum-offload (bool) – since 0.104

                (networkd backend only) If set to true (false), the hardware offload for checksumming of ingress
                network packets is enabled (disabled).  When unset, the kernel's default will be used.

       • transmit-checksum-offload (bool) – since 0.104

                (networkd  backend only) If set to true (false), the hardware offload for checksumming of egress
                network packets is enabled (disabled).  When unset, the kernel's default will be used.

       • tcp-segmentation-offload (bool) – since 0.104

                (networkd backend only) If set to true (false), the TCP Segmentation Offload  (TSO)  is  enabled
                (disabled).  When unset, the kernel's default will be used.

       • tcp6-segmentation-offload (bool) – since 0.104

                (networkd   backend   only)  If  set  to  true  (false),  the  TCP6  Segmentation  Offload  (tx-
                tcp6-segmentation) is enabled (disabled).  When unset, the kernel's default will be used.

       • generic-segmentation-offload (bool) – since 0.104

                (networkd backend only) If set to true  (false),  the  Generic  Segmentation  Offload  (GSO)  is
                enabled (disabled).  When unset, the kernel's default will be used.

       • generic-receive-offload (bool) – since 0.104

                (networkd  backend  only)  If  set to true (false), the Generic Receive Offload (GRO) is enabled
                (disabled).  When unset, the kernel's default will be used.

       • large-receive-offload (bool) – since 0.104

                (networkd backend only) If set to true (false), the  Large  Receive  Offload  (LRO)  is  enabled
                (disabled).  When unset, the kernel's default will be used.

       • openvswitch (mapping) – since 0.100

                This  provides  additional configuration for the openvswitch network device.  If Open vSwitch is
                not available on the system, netplan treats the presence  of  openvswitch  configuration  as  an
                error.

                Any  supported  network device that is declared with the openvswitch mapping (or any bond/bridge
                that includes an interface with an openvswitch configuration) will  be  created  in  openvswitch
                instead  of  the  defined  renderer.   In  the  case of a vlan definition declared the same way,
                netplan will create a fake VLAN bridge in openvswitch with the requested vlan properties.

         • external-ids (mapping) – since 0.100

                  Passed-through directly to Open vSwitch

         • other-config (mapping) – since 0.100

                  Passed-through directly to Open vSwitch

         • lacp (scalar) – since 0.100

                  Valid for bond interfaces.  Accepts active, passive or off (the default).

         • fail-mode (scalar) – since 0.100

                  Valid for bridge interfaces.  Accepts secure or standalone (the default).

         • mcast-snooping (bool) – since 0.100

                  Valid for bridge interfaces.  False by default.

         • protocols (sequence of scalars) – since 0.100

                  Valid for bridge interfaces or the network  section.   List  of  protocols  to  be  used  when
                  negotiating  a  connection  with  the controller.  Accepts OpenFlow10, OpenFlow11, OpenFlow12,
                  OpenFlow13, OpenFlow14, and OpenFlow15.

         • rstp (bool) – since 0.100

                  Valid for bridge interfaces.  False by default.

         • controller (mapping) – since 0.100

                  Valid for bridge interfaces.  Specify an external OpenFlow controller.

           • addresses (sequence of scalars)

                    Set the list of addresses to use for the controller targets.  The syntax of these  addresses
                    is    as    defined    in    ovs-vsctl(8).     Example:    addresses:   [tcp:127.0.0.1:6653,
                    "ssl:[fe80::1234%eth0]:6653"]

           • connection-mode (scalar)

                    Set the connection mode for the controller.  Supported options are in-band and  out-of-band.
                    The default is in-band.

         • ports (sequence of sequence of scalars) – since 0.100

                  Open vSwitch patch ports.  Each port is declared as a pair of names which can be referenced as
                  interfaces in dependent virtual devices (bonds, bridges).

           Example:

                  openvswitch:
                    ports:
                      - [patch0-1, patch1-0]

         • ssl (mapping) – since 0.100

                  Valid for global openvswitch settings.  Options for configuring SSL server  endpoint  for  the
                  switch.

           • ca-cert (scalar)

                    Path to a file containing the CA certificate to be used.

           • certificate (scalar)

                    Path to a file containing the server certificate.

           • private-key (scalar)

                    Path to a file containing the private key for the server.

   Properties for all device typesrenderer (scalar)

                Use  the  given  networking  backend  for this definition.  Currently supported are networkd and
                NetworkManager.  This property can be specified globally in network:, for a device type  (in  e.
                g.  ethernets:) or for a particular device definition.  Default is networkd.

                (Since  0.99) The renderer property has one additional acceptable value for vlan objects (i.  e.
                defined in vlans:): sriov.  If a vlan is defined with the sriov renderer for an  SR-IOV  Virtual
                Function  interface,  this causes netplan to set up a hardware VLAN filter for it.  There can be
                only one defined per VF.

       • dhcp4 (bool)

                Enable DHCP for IPv4.  Off by default.

       • dhcp6 (bool)

                Enable DHCP for IPv6.  Off by default.  This covers both stateless DHCP - where the DHCP  server
                supplies  information like DNS nameservers but not the IP address - and stateful DHCP, where the
                server provides both the address and the other information.

                If you are in an IPv6-only environment with completely stateless auto-configuration (SLAAC  with
                RDNSS),  this  option  can  be  set to cause the interface to be brought up.  (Setting accept-ra
                alone is not sufficient.) Auto-configuration  will  still  honor  the  contents  of  the  router
                advertisement and only use DHCP if requested in the RA.

                Note  that  rdnssd(8) is required to use RDNSS with networkd.  No extra software is required for
                NetworkManager.

       • ipv6-mtu (scalar) – since 0.98 > Set the IPv6 MTU (only supported with networkd backend).  Note >  that
         needing to set this is an unusual requirement.  > > Requires feature: ipv6-mtuipv6-privacy (bool)

                Enable  IPv6  Privacy  Extensions  (RFC  4941) for the specified interface, and prefer temporary
                addresses.  Defaults to false - no privacy extensions.  There is currently  no  way  to  have  a
                private address but prefer the public address.

       • link-local (sequence of scalars)

                Configure  the  link-local  addresses  to  bring up.  Valid options are 'ipv4' and 'ipv6', which
                respectively allow enabling IPv4 and IPv6 link local addressing.  If this field is not  defined,
                the default is to enable only IPv6 link-local addresses.  If the field is defined but configured
                as an empty set, IPv6 link-local addresses are disabled as well as IPv4 link- local addresses.

                This  feature  enables  or  disables  link-local  addresses  for  a  protocol,  but  the  actual
                implementation differs per backend.  On networkd, this directly changes the behavior and may add
                an extra address on an interface.  When using the NetworkManager  backend,  enabling  link-local
                has no effect if the interface also has DHCP enabled.

         Examples:

         • Enable only IPv4 link-local: link-local: [ ipv4 ]

         • Enable all link-local addresses: link-local: [ ipv4, ipv6 ]

         • Disable all link-local addresses: link-local: [ ]

       • ignore-carrier (bool) – since 0.104

                (networkd  backend  only)  Allow  the  specified  interface  to  be configured even if it has no
                carrier.

       • critical (bool)

                Designate the connection as "critical to the system", meaning that special care will be taken by
                to not release the assigned IP when the daemon is restarted.  (not recognized by NetworkManager)

       • dhcp-identifier (scalar)

                (networkd  backend  only) Sets the source of DHCPv4 client identifier.  If mac is specified, the
                MAC address of the link is used.  If this option is omitted, or if duid is  specified,  networkd
                will  generate  an RFC4361-compliant client identifier for the interface by combining the link's
                IAID and DUID.

       • dhcp4-overrides (mapping)

                (networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides section below.

       • dhcp6-overrides (mapping)

                (networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides section below.

       • accept-ra (bool)

                Accept Router Advertisement that would have the kernel configure IPv6 by itself.  When  enabled,
                accept Router Advertisements.  When disabled, do not respond to Router Advertisements.  If unset
                use the host kernel default setting.

       • addresses (sequence of scalars and mappings)

                Add static addresses to the interface in addition to the ones received through DHCP or RA.  Each
                sequence entry is in CIDR notation, i.  e.  of the form addr/prefixlen.  addr is an IPv4 or IPv6
                address as recognized by inet_pton(3) and prefixlen the number of bits of the subnet.

                For virtual devices (bridges, bonds, vlan) if  there  is  no  address  configured  and  DHCP  is
                disabled,  the  interface  may  still  be  brought  online, but will not be addressable from the
                network.

                In addition to the addresses themselves one can specify configuration  parameters  as  mappings.
                Current supported options are:

         • lifetime (scalar) – since 0.100

                  Default: forever.  This can be forever or 0 and corresponds to the PreferredLifetime option in
                  systemd-networkd's Address section.  Currently supported on the networkd backend only.

         • label (scalar) – since 0.100

                  An IP address label, equivalent to the ip address label command.  Currently supported  on  the
                  networkd backend only.

         Examples:

         • Simple: addresses: [192.168.14.2/24, "2001:1::1/64"]

         • Advanced:

                  network:
                    ethernets:
                      eth0:
                        addresses:
                          - "10.0.0.15/24":
                              lifetime: 0
                              label: "maas"
                          - "2001:1::1/64"

       • ipv6-address-generation (scalar) – since 0.99

                Configure  method  for  creating  the  address for use with RFC4862 IPv6 Stateless Address Auto-
                configuration (only supported with  NetworkManager  backend).   Possible  values  are  eui64  or
                stable-privacy.

       • ipv6-address-token (scalar) – since 0.100

                Define  an  IPv6  address  token  for  creating a static interface identifier for IPv6 Stateless
                Address Auto-configuration.  This is mutually exclusive with ipv6-address-generation.

       • gateway4, gateway6 (scalar)

                Deprecated,  see  Default  routes.   Set  default  gateway  for  IPv4/6,  for   manual   address
                configuration.   This  requires setting addresses too.  Gateway IPs must be in a form recognized
                by inet_pton(3).  There should only be a single gateway per IP address family set in your global
                config,  to  make  it  unambiguous.  If you need multiple default routes, please define them via
                routing-policy.

         Examples

         • IPv4: gateway4: 172.16.0.1

         • IPv6: gateway6: "2001:4::1"

       • nameservers (mapping)

                Set DNS servers and search domains, for manual address configuration.  There are  two  supported
                fields:  addresses:  is  a  list of IPv4 or IPv6 addresses similar to gateway*, and search: is a
                list of search domains.

         Example:

                network:
                  ethernets:
                    id0:
                      [...]
                      nameservers:
                        search: [lab, home]
                        addresses: [8.8.8.8, "FEDC::1"]

       • macaddress (scalar)

                Set the device's MAC address.  The MAC address must be in the form "XX:XX:XX:XX:XX:XX".

                Note: This will not work reliably for devices matched by name only and rendered by networkd, due
                to interactions with device renaming in udev.  Match devices by MAC when setting MAC addresses.

         Example:

                network:
                  ethernets:
                    id0:
                      match:
                        macaddress: 52:54:00:6b:3c:58
                      [...]
                      macaddress: 52:54:00:6b:3c:59

       • mtu (scalar)

                Set  the Maximum Transmission Unit for the interface.  The default is 1500.  Valid values depend
                on your network interface.

                Note: This will not work reliably for devices matched by name only and rendered by networkd, due
                to interactions with device renaming in udev.  Match devices by MAC when setting MTU.

       • optional (bool)

                An  optional  device  is  not  required for booting.  Normally, networkd will wait some time for
                device to become configured before proceeding with booting.  However, if a device is  marked  as
                optional, networkd will not wait for it.  This is only supported by networkd, and the default is
                false.

         Example:

                network:
                  ethernets:
                    eth7:
                      # this is plugged into a test network that is often
                      # down - don't wait for it to come up during boot.
                      dhcp4: true
                      optional: true

       • optional-addresses (sequence of scalars)

                Specify types of addresses that are not required for a device to  be  considered  online.   This
                changes  the  behavior  of  backends at boot time to avoid waiting for addresses that are marked
                optional, and thus consider the interface as "usable"  sooner.   This  does  not  disable  these
                addresses, which will be brought up anyway.

         Example:

                network:
                  ethernets:
                    eth7:
                      dhcp4: true
                      dhcp6: true
                      optional-addresses: [ ipv4-ll, dhcp6 ]

       • activation-mode (scalar) – since 0.103

                Allows  specifying  the management policy of the selected interface.  By default, netplan brings
                up any configured interface if possible.  Using the activation-mode setting users  can  override
                that  behavior by either specifying manual, to hand over control over the interface state to the
                administrator or (for networkd backend only) off to force the link in a down state at all times.
                Any  interface  with  activation-mode  defined  is  implicitly  considered  optional.  Supported
                officially as of networkd v248+.

         Example:

                network:
                  ethernets:
                    eth1:
                      # this interface will not be put into an UP state automatically
                      dhcp4: true
                      activation-mode: manual

       • routes (sequence of mappings)

                Configure static routing for the device; see the Routing section below.

       • routing-policy (sequence of mappings)

                Configure policy routing for the device; see the Routing section below.

       • neigh-suppress (scalar) – since 0.105

                Takes a boolean.  Configures whether ARP and ND neighbor suppression is enabled for  this  port.
                When unset, the kernel's default will be used.

   DHCP Overrides
       Several  DHCP  behavior  overrides  are  available.   Most  currently only have any effect when using the
       networkd backend, with the exception of use-routes and route-metric.

       Overrides only have an effect if the corresponding dhcp4 or dhcp6 is set to true.

       If both dhcp4 and dhcp6 are true, the networkd backend requires that dhcp4-overrides and  dhcp6-overrides
       contain  the  same  keys  and values.  If the values do not match, an error will be shown and the network
       configuration will not be applied.

       When using the NetworkManager  backend,  different  values  may  be  specified  for  dhcp4-overrides  and
       dhcp6-overrides, and will be applied to the DHCP client processes as specified in the netplan YAML.

       • dhcp4-overrides, dhcp6-overrides (mapping)

                The dhcp4-overrides and `dhcp6-override`` mappings override the default DHCP behavior.

         • use-dns (bool)

                  Default: true.  When true, the DNS servers received from the DHCP server will be used and take
                  precedence over any statically configured ones.  Currently only has an effect on the  networkd
                  backend.

         • use-ntp (bool)

                  Default:  true.   When  true,  the  NTP  servers received from the DHCP server will be used by
                  systemd-timesyncd and take precedence over any statically configured ones.  Currently only has
                  an effect on the networkd backend.

         • send-hostname (bool)

                  Default:  true.  When true, the machine's hostname will be sent to the DHCP server.  Currently
                  only has an effect on the networkd backend.

         • use-hostname (bool)

                  Default: true.  When true, the hostname received from the DHCP  server  will  be  set  as  the
                  transient hostname of the system.  Currently only has an effect on the networkd backend.

         • use-mtu (bool)

                  Default: true.  When true, the MTU received from the DHCP server will be set as the MTU of the
                  network interface.  When false, the MTU  advertised  by  the  DHCP  server  will  be  ignored.
                  Currently only has an effect on the networkd backend.

         • hostname (scalar)

                  Use  this  value  for  the  hostname  which  is  sent to the DHCP server, instead of machine's
                  hostname.  Currently only has an effect on the networkd backend.

         • use-routes (bool)

                  Default: true.  When true, the routes received from the DHCP server will be installed  in  the
                  routing  table  normally.   When set to false, routes from the DHCP server will be ignored: in
                  this case, the user is responsible for adding static routes if necessary for  correct  network
                  operation.   This allows users to avoid installing a default gateway for interfaces configured
                  via DHCP.  Available for both the networkd and NetworkManager backends.

         • route-metric (scalar)

                  Use this value for default metric for automatically-added  routes.   Use  this  to  prioritize
                  routes for devices by setting a lower metric on a preferred interface.  Available for both the
                  networkd and NetworkManager backends.

         • use-domains (scalar) – since 0.98

                  Takes a boolean, or the special value "route".  When true, the domain name received  from  the
                  DHCP  server  will  be  used as DNS search domain over this link, similar to the effect of the
                  Domains= setting.  If set to "route", the domain name received from the DHCP  server  will  be
                  used  for  routing  DNS  queries  only,  but  not  for searching, similar to the effect of the
                  Domains= setting when the argument is prefixed with "~".

                  Requires feature: dhcp-use-domains

   Routing
       Complex routing is possible with netplan.  Standard static routes as well as policy routing using routing
       tables are supported via the networkd backend.

       These options are available for all types of interfaces.

   Default routes
       The  most  common need for routing concerns the definition of default routes to reach the wider Internet.
       Those default routes can only defined once per IP family and routing table.  A typical example would look
       like the following:

              network:
                ethernets:
                  eth0:
                    [...]
                    routes:
                      - to: default # could be 0.0.0.0/0 optionally
                        via: 10.0.0.1
                        metric: 100
                        on-link: true
                      - to: default # could be ::/0 optionally
                        via: cf02:de:ad:be:ef::2
                  eth1:
                    [...]
                    routes:
                      - to: default
                        via: 172.134.67.1
                        metric: 100
                        on-link: true
                        # Not on the main routing table,
                        # does not conflict with the eth0 default route
                    table: 76

       • routes (mapping)

                The  routes  block  defines  standard  static  routes  for  an  interface.   At least to must be
                specified.  If type is local or nat a default scope of host is assumed.  If type is unicast  and
                no  gateway (via) is given or type is broadcast, multicast or anycast a default scope of link is
                assumed.  Otherwise, a global scope is the default setting.

                For from, to, and via, both IPv4 and IPv6 addresses are recognized, and  must  be  in  the  form
                addr/prefixlen or addr.

         • from (scalar)

                  Set a source IP address for traffic going through the route.  (NetworkManager: as of v1.8.0)

         • to (scalar)

                  Destination address for the route.

         • via (scalar)

                  Address to the gateway to use for this route.

         • on-link (bool)

                  When  set  to  "true",  specifies  that  the  route  is  directly  connected to the interface.
                  (NetworkManager: as of v1.12.0 for IPv4 and v1.18.0 for IPv6)

         • metric (scalar)

                  The relative priority of the route.  Must be a positive integer value.

         • type (scalar)

                  The  type  of  route.   Valid  options  are  "unicast"  (default),   "anycast",   "blackhole",
                  "broadcast", "local", "multicast", "nat", "prohibit", "throw", "unreachable" or "xresolve".

         • scope (scalar)

                  The route scope, how wide-ranging it is to the network.  Possible values are "global", "link",
                  or "host".  Applies to IPv4 only.

         • table (scalar)

                  The table number to use for the route.  In some scenarios, it may be useful to set routes in a
                  separate  routing  table.   It  may  also  be used to refer to routing policy rules which also
                  accept a table parameter.  Allowed values are positive integers starting from 1.  Some  values
                  are  already  in  use  to  refer  to  specific  routing  tables:  see /etc/iproute2/rt_tables.
                  (NetworkManager: as of v1.10.0)

         • mtu (scalar) – since 0.101

                  The MTU to be used for the route, in bytes.  Must be a positive integer value.

         • congestion-window (scalar) – since 0.102

                  The congestion window to be used for the route, represented by number of segments.  Must be  a
                  positive integer value.

         • advertised-receive-window (scalar) – since 0.102

                  The receive window to be advertised for the route, represented by number of segments.  Must be
                  a positive integer value.

       • routing-policy (mapping)

                The routing-policy block defines extra routing policy  for  a  network,  where  traffic  may  be
                handled specially based on the source IP, firewall marking, etc.

                For  from,  to,  both  IPv4  and  IPv6  addresses  are  recognized,  and  must  be  in  the form
                addr/prefixlen or addr.

         • from (scalar)

                  Set a source IP address to match traffic for this policy rule.

         • to (scalar)

                  Match on traffic going to the specified destination.

         • table (scalar)

                  The table number to match for the route.  In some scenarios, it may be useful to set routes in
                  a  separate  routing  table.  It may also be used to refer to routes which also accept a table
                  parameter.  Allowed values are positive integers starting from 1.  Some values are already  in
                  use to refer to specific routing tables: see /etc/iproute2/rt_tables.

         • priority (scalar)

                  Specify  a priority for the routing policy rule, to influence the order in which routing rules
                  are processed.  A higher number  means  lower  priority:  rules  are  processed  in  order  by
                  increasing priority number.

         • mark (scalar)

                  Have  this  routing policy rule match on traffic that has been marked by the iptables firewall
                  with this value.  Allowed values are positive integers starting from 1.

         • type-of-service (scalar)

                  Match this policy rule based on the type of service number applied to the traffic.

   Authentication
       Netplan supports advanced authentication settings for ethernet and wifi interfaces, as well as individual
       wifi networks, by means of the auth block.

       • auth (mapping)

                Specifies authentication settings for a device of type ethernets:, or an access-points: entry on
                a wifis: device.

                The auth block supports the following properties:

         • key-management (scalar)

                  The supported key management modes are none (no key management); psk (WPA with pre-shared key,
                  common for home wifi); eap (WPA with EAP, common for enterprise wifi); sae (used by WPA3); and
                  802.1x (used primarily for wired Ethernet connections).

         • password (scalar)

                  The password string for EAP, or the pre-shared key for WPA-PSK.

           The following properties can be used if key-management is eap or 802.1x:

         • method (scalar)

                  The EAP method to use.  The supported EAP methods are tls (TLS),  peap  (Protected  EAP),  and
                  ttls (Tunneled TLS).

         • identity (scalar)

                  The identity to use for EAP.

         • anonymous-identity (scalar)

                  The  identity to pass over the unencrypted channel if the chosen EAP method supports passing a
                  different tunnelled identity.

         • ca-certificate (scalar)

                  Path to a file with one or more trusted certificate authority (CA) certificates.

         • client-certificate (scalar)

                  Path to a file containing the certificate to be used by the client during authentication.

         • client-key (scalar)

                  Path to a file containing the private key corresponding to client-certificate.

         • client-key-password (scalar)

                  Password to use to decrypt the private key specified in client-key if it is encrypted.

         • phase2-auth (scalar) – since 0.99

                  Phase 2 authentication mechanism.

   Properties for device type ethernets:
       Status: Optional.

       Purpose: Use the ethernets key to configure Ethernet interfaces.

       Structure: The key consists of a mapping of Ethernet interface  IDs.   Each  ethernet  has  a  number  of
       configuration  options.   You  don't  need  to  define  each interface by their name inside the ethernets
       mapping.  You can use any ID that describes the interface and match the actual  network  card  using  the
       match key.  The general configuration structure for Ethernets is shown below.

              network:
                ethernets:
                  device-id:
                    ...

       device-id  is the interface identifier.  If you use the interface name as the ID, Netplan will match that
       interface.

       Consider the example below.  In this case, an interface called eth0 will be configured with DHCP.

              network:
                ethernets:
                  eth0:
                    dhcp4: true

       The device-id can be any descriptive name your find meaningful.  Although, if it  doesn't  match  a  real
       interface name, you must use the property match to identify the device you want to configure.

       The  example  below defines an Ethernet connection called isp-interface (supposedly an external interface
       connected to the Internet Service Provider) and uses match to apply the  configuration  to  the  physical
       device with MAC address aa:bb:cc:00:11:22.

              network:
                ethernets:
                  isp-interface:
                    match:
                      macaddress: aa:bb:cc:00:11:22
                    dhcp4: true

       Ethernet  device definitions, beyond common ones described above, also support some additional properties
       that can be used for SR-IOV devices.

       • link (scalar) – since 0.99

                (SR-IOV devices only) The link property declares  the  device  as  a  Virtual  Function  of  the
                selected Physical Function device, as identified by the given netplan id.

         Example:

                network:
                  ethernets:
                    enp1: {...}
                    enp1s16f1:
                      link: enp1

       • virtual-function-count (scalar) – since 0.99

                (SR-IOV  devices  only)  In  certain  special  cases  VFs might need to be configured outside of
                netplan.  For such configurations virtual-function-count  can  be  optionally  used  to  set  an
                explicit  number of Virtual Functions for the given Physical Function.  If unset, the default is
                to create only as many VFs as are defined in the netplan configuration.  This should be used for
                special cases only.

                Requires feature: sriovembedded-switch-mode (scalar) – since 0.104

                (SR-IOV devices only) Change the operational mode of the embedded switch of a supported SmartNIC
                PCI device (e.g.  Mellanox ConnectX-5).  Possible values are switchdev or legacy, if unspecified
                the vendor's default configuration is used.

                Requires feature: eswitch-modedelay-virtual-functions-rebind (bool) – since 0.104

                (SR-IOV  devices  only) Delay rebinding of SR-IOV virtual functions to its driver after changing
                the embedded-switch-mode setting to a later stage.  Can be enabled when  bonding/VF  LAG  is  in
                use.  Defaults to false.

                Requires feature: eswitch-modeinfiniband-mode (scalar) – since 0.105

                (InfiniBand  devices  only)  Change the operational mode of a IPoIB device.  Possible values are
                datagram or connected.  If unspecified the kernel's default configuration is used.

                Requires feature: infiniband

   Properties for device type modems:
       Status: Optional.

       Purpose: Use the modems key  to  configure  Modem  interfaces.   GSM/CDMA  modem  configuration  is  only
       supported for the NetworkManager backend.  systemd-networkd does not support modems.

       Structure: The key consists of a mapping of Modem IDs.  Each modem has a number of configuration options.
       The general configuration structure for Modems is shown below.

              network:
                version: 2
                renderer: NetworkManager
                modems:
                  cdc-wdm1:
                    mtu: 1600
                    apn: ISP.CINGULAR
                    username: ISP@CINGULARGPRS.COM
                    password: CINGULAR1
                    number: "*99#"
                    network-id: 24005
                    device-id: da812de91eec16620b06cd0ca5cbc7ea25245222
                    pin: 2345
                    sim-id: 89148000000060671234
                    sim-operator-id: 310260

       Requires feature: modemsapn (scalar) – since 0.99

                Set the carrier APN (Access Point Name).  This can be omitted if auto-config is enabled.

       • auto-config (bool) – since 0.99

                Specify whether to try and auto-configure the modem by doing a lookup of the carrier against the
                Mobile Broadband Provider database.  This may not work for all carriers.

       • device-id (scalar) – since 0.99

                Specify the device ID (as given by the WWAN management service) of the modem to match.  This can
                be found using mmcli.

       • network-id (scalar) – since 0.99

                Specify the Network ID (GSM LAI format).  If  this  is  specified,  the  device  will  not  roam
                networks.

       • number (scalar) – since 0.99

                The number to dial to establish the connection to the mobile broadband network.  (Deprecated for
                GSM)

       • password (scalar) – since 0.99

                Specify the password used to authenticate with the carrier network.   This  can  be  omitted  if
                auto-config is enabled.

       • pin (scalar) – since 0.99

                Specify the SIM PIN to allow it to operate if a PIN is set.

       • sim-id (scalar) – since 0.99

                Specify  the  SIM  unique  identifier  (as  given  by  the  WWAN  management service) which this
                connection applies to.  If given, the connection will  apply  to  any  device  also  allowed  by
                device-id which contains a SIM card matching the given identifier.

       • sim-operator-id (scalar) – since 0.99

                Specify  the MCC/MNC string (such as "310260" or "21601") which identifies the carrier that this
                connection should apply to.  If given, the connection will apply to any device also  allowed  by
                device-id and sim-id which contains a SIM card provisioned by the given operator.

       • username (scalar) – since 0.99

                Specify  the  username  used  to  authenticate with the carrier network.  This can be omitted if
                auto-config is enabled.

   Properties for device type wifis:
       Status: Optional.

       Purpose: Use the wifis key to configure WiFi access points.

       Structure: The key consists of a mapping of WiFi IDs.  Each wifi has a number of  configuration  options.
       The general configuration structure for WiFis is shown below.

              network:
                version: 2
                wifis:
                  wlp0s1:
                    access-points:
                      "network_ssid_name":
                        password: "**********"

       Note that systemd-networkd does not natively support wifi, so you need wpasupplicant installed if you let
       the networkd renderer handle wifi.

       • access-points (mapping)

                This provides pre-configured connections to NetworkManager.   Note  that  users  can  of  course
                select  other  access  points/SSIDs.   The keys of the mapping are the SSIDs, and the values are
                mappings with the following supported properties:

         • password (scalar)

                  Enable WPA/WPA2 authentication and set the passphrase for it.  If neither  this  nor  an  auth
                  block are given, the network is assumed to be open.  The setting

                         password: "S3kr1t"

                  is equivalent to

                         auth:
                           key-management: psk
                           password: "S3kr1t"

         • mode (scalar)

                  Possible  access  point  modes are infrastructure (the default), ap (create an access point to
                  which other devices can connect), and adhoc (peer to peer networks without  a  central  access
                  point).  ap is only supported with NetworkManager.

         • bssid (scalar) – since 0.99

                  If specified, directs the device to only associate with the given access point.

         • band (scalar) – since 0.99

                  Possible bands are 5GHz (for 5GHz 802.11a) and 2.4GHz (for 2.4GHz 802.11), do not restrict the
                  802.11 frequency band of the network if unset (the default).

         • channel (scalar) – since 0.99

                  Wireless channel to use for the Wi-Fi connection.  Because  channel  numbers  overlap  between
                  bands, this property takes effect only if the band property is also set.

         • hidden (bool) – since 0.100

                  Set  to  true  to change the SSID scan technique for connecting to hidden WiFi networks.  Note
                  this may have slower performance compared to false (the default) when connecting  to  publicly
                  broadcast SSIDs.

       • wakeonwlan (sequence of scalars) – since 0.99

                This  enables WakeOnWLan on supported devices.  Not all drivers support all options.  May be any
                combination   of    any,    disconnect,    magic_pkt,    gtk_rekey_failure,    eap_identity_req,
                four_way_handshake,  rfkill_release or tcp (NetworkManager only).  Or the exclusive default flag
                (the default).

       • regulatory-domain (scalar) – since 0.105

                This can be used to define the radio's  regulatory  domain,  to  make  use  of  additional  WiFi
                channels  outside  the  "world domain".  Takes an ISO / IEC 3166 country code (like GB) or 00 to
                reset         to         the         "world         domain".          See         wireless-regdb
                (https://git.kernel.org/pub/scm/linux/kernel/git/sforshee/wireless-regdb.git/tree/db.txt)    for
                available values.

                Requires dependency: iw, if it is to be used outside the networkd (wpa_supplicant) backend.

   Properties for device type bridges:
       Status: Optional.

       Purpose: Use the bridges key to create Bridge interfaces.

       Structure: The key consists of a mapping of Bridge interface names.  Each bridge has an optional list  of
       interfaces that will be bridged together.  The interfaces listed in the interfaces key (enp5s0 and enp5s1
       below) must also be defined in your Netplan  configuration.   The  general  configuration  structure  for
       Bridges is shown below.

              network:
                bridges:
                  br0:
                    interfaces:
                      - enp5s0
                      - enp5s1
                    dhcp4: true
                    ...

       When applied, a virtual interface of type bridge called br0 will be created in the system.

       The specific settings for bridges are defined below.

       • interfaces (sequence of scalars)

                All  devices  matching  this ID list will be added to the bridge.  This may be an empty list, in
                which case the bridge will be brought online with no member interfaces.

         Example:

                network:
                  ethernets:
                    switchports:
                      match: {name: "enp2*"}
                  [...]
                  bridges:
                    br0:
                      interfaces: [switchports]

       • parameters (mapping)

                Customization parameters for special bridging options.  Time intervals may need to be  expressed
                as  a  number  of  seconds  or  milliseconds:  the  default  value  type is specified below.  If
                necessary, time intervals can be qualified using a time suffix (such as "s"  for  seconds,  "ms"
                for milliseconds) to allow for more control over its behavior.

         • ageing-time, aging-time (scalar)

                  Set  the  period  of  time  to keep a MAC address in the forwarding database after a packet is
                  received.  This maps to the AgeingTimeSec= property when the networkd renderer is used.  If no
                  time suffix is specified, the value will be interpreted as seconds.

         • priority (scalar)

                  Set  the  priority  value  for the bridge.  This value should be a number between 0 and 65535.
                  Lower values mean higher priority.  The bridge with the higher priority will be elected as the
                  root bridge.

         • port-priority (mapping)

                  Set  the  port priority per interface.  The priority value is a number between 0 and 63.  This
                  metric is used in the designated port and root port selection algorithms.

           Example:

                  network:
                    ethernets:
                      eth0:
                        dhcp4: false
                      eth1:
                        dhcp4: false
                    bridges:
                      br0:
                        interfaces: [eth0, eth1]
                        parameters:
                          port-priority:
                            eth0: 10
                            eth1: 20

         • forward-delay (scalar)

                  Specify the period of time the bridge will remain in  Listening  and  Learning  states  before
                  getting  to  the  Forwarding  state.  This field maps to the ForwardDelaySec= property for the
                  networkd renderer.  If no time suffix is specified, the value will be interpreted as seconds.

         • hello-time (scalar)

                  Specify the interval between two hello packets being sent out from  the  root  and  designated
                  bridges.  Hello packets communicate information about the network topology.  When the networkd
                  renderer is used, this maps to the HelloTimeSec= property.  If no time  suffix  is  specified,
                  the value will be interpreted as seconds.

         • max-age (scalar)

                  Set the maximum age of a hello packet.  If the last hello packet is older than that value, the
                  bridge will attempt to become the root bridge.  This maps to the MaxAgeSec= property when  the
                  networkd  renderer  is used.  If no time suffix is specified, the value will be interpreted as
                  seconds.

         • path-cost (mapping)

                  Set the per-interface cost of a path on the bridge.  Faster interfaces  should  have  a  lower
                  cost.   This  allows  a  finer  control  on the network topology so that the fastest paths are
                  available whenever possible.

           Example:

                  network:
                    ethernets:
                      eth0:
                        dhcp4: false
                      eth1:
                        dhcp4: false
                    bridges:
                      br0:
                        interfaces: [eth0, eth1]
                        parameters:
                          path-cost:
                            eth0: 100
                            eth1: 200

         • stp (bool)

                  Define whether the bridge should use Spanning Tree Protocol.  The  default  value  is  "true",
                  which means that Spanning Tree should be used.

   Properties for device type bonds:
       Status: Optional.

       Purpose: Use the bonds key to create Bond (Link Aggregation) interfaces.

       Structure:  The  key  consists  of  a mapping of Bond interface names.  Each bond has an optional list of
       interfaces that will be part of the aggregation.  The interfaces listed in the interfaces key  must  also
       be defined in your Netplan configuration.  The general configuration structure for Bonds is shown below.

              network:
                bonds:
                  bond0:
                    interfaces:
                      - enp5s0
                      - enp5s1
                      - enp5s2
                    mode: active-backup
                    ...

       When applied, a virtual interface of type bond called bond0 will be created in the system.

       The specific settings for bonds are defined below.

       • interfaces (sequence of scalars)

                All devices matching this ID list will be added to the bond.

         Example:

                network:
                  ethernets:
                    switchports:
                      match: {name: "enp2*"}
                  [...]
                  bonds:
                    bond0:
                      interfaces: [switchports]

       • parameters (mapping)

                Customization  parameters  for special bonding options.  Time intervals may need to be expressed
                as a number of seconds  or  milliseconds:  the  default  value  type  is  specified  below.   If
                necessary,  time  intervals  can be qualified using a time suffix (such as "s" for seconds, "ms"
                for milliseconds) to allow for more control over its behavior.

         • mode (scalar)

                  Set the bonding mode used for the  interfaces.   The  default  is  balance-rr  (round  robin).
                  Possible  values  are balance-rr, active-backup, balance-xor, broadcast, 802.3ad, balance-tlb,
                  and balance-alb.  For Open vSwitch active-backup and  the  additional  modes  balance-tcp  and
                  balance-slb are supported.

         • lacp-rate (scalar)

                  Set the rate at which LACPDUs are transmitted.  This is only useful in 802.3ad mode.  Possible
                  values are slow (30 seconds, default), and fast (every second).

         • mii-monitor-interval (scalar)

                  Specifies the interval for MII monitoring (verifying if an interface of the bond has carrier).
                  The  default  is  0;  which disables MII monitoring.  This is equivalent to the MIIMonitorSec=
                  field for the networkd backend.  If no time suffix is specified, the value will be interpreted
                  as milliseconds.

         • min-links (scalar)

                  The minimum number of links up in a bond to consider the bond interface to be up.

         • transmit-hash-policy (scalar)

                  Specifies  the  transmit  hash  policy  for  the  selection  of ports.  This is only useful in
                  balance-xor, 802.3ad and balance-tlb modes.  Possible values are layer2,  layer3+4,  layer2+3,
                  encap2+3, and encap3+4.

         • ad-select (scalar)

                  Set  the  aggregation selection mode.  Possible values are stable, bandwidth, and count.  This
                  option is only used in 802.3ad mode.

         • all-members-active (bool) – since 0.106

                  If the bond should drop duplicate frames received on inactive ports, set this option to false.
                  If  they should be delivered, set this option to true.  The default value is false, and is the
                  desirable behavior in most situations.

                  Alias: all-slaves-activearp-interval (scalar)

                  Set the interval value for how frequently ARP link  monitoring  should  happen.   The  default
                  value  is  0,  which  disables  ARP  monitoring.   For  the networkd backend, this maps to the
                  ARPIntervalSec= property.  If no time suffix is specified, the value will  be  interpreted  as
                  milliseconds.

         • arp-ip-targets (sequence of scalars)

                  IPs  of  other hosts on the link which should be sent ARP requests in order to validate that a
                  port is up.  This option is only used when arp-interval is set to a value other  than  0.   At
                  least  one  IP address must be given for ARP link monitoring to function.  Only IPv4 addresses
                  are supported.  You can specify up to 16 IP addresses.  The default value is an empty list.

         • arp-validate (scalar)

                  Configure how ARP replies are to be validated when using ARP link monitoring.  Possible values
                  are none, active, backup, and all.

         • arp-all-targets (scalar)

                  Specify  whether  to  use any ARP IP target being up as sufficient for a port to be considered
                  up; or if all the targets must be up.  This is only used  for  active-backup  mode  when  arp-
                  validate is enabled.  Possible values are any and all.

         • up-delay (scalar)

                  Specify the delay before enabling a link once the link is physically up.  The default value is
                  0.  This maps to the UpDelaySec= property for the networkd  renderer.   This  option  is  only
                  valid  for  the  miimon  link  monitor.   If  no  time  suffix is specified, the value will be
                  interpreted as milliseconds.

         • down-delay (scalar)

                  Specify the delay before disabling a link once the link has been lost.  The default  value  is
                  0.   This  maps  to the DownDelaySec= property for the networkd renderer.  This option is only
                  valid for the miimon link monitor.  If  no  time  suffix  is  specified,  the  value  will  be
                  interpreted as milliseconds.

         • fail-over-mac-policy (scalar)

                  Set whether to set all ports to the same MAC address when adding them to the bond, or how else
                  the system should handle MAC addresses.  The possible values are none, active, and follow.

         • gratuitous-arp (scalar)

                  Specify how many ARP packets to send after failover.  Once a link is  up  on  a  new  port,  a
                  notification  is  sent  and possibly repeated if this value is set to a number greater than 1.
                  The default value is 1 and valid values are between 1 and  255.   This  only  affects  active-
                  backup mode.

                  For  historical  reasons,  the  misspelling  gratuitious-arp is also accepted and has the same
                  function.

         • packets-per-member (scalar) – since 0.106

                  In balance-rr mode, specifies the number of packets to transmit on a port before switching  to
                  the  next.   When  this  value  is set to 0, ports are chosen at random.  Allowable values are
                  between 0 and 65535.  The default value is 1.  This setting is only used in balance-rr mode.

                  Alias: packets-per-slaveprimary-reselect-policy (scalar)

                  Set the reselection policy for the primary port.  On failure of the active  port,  the  system
                  will use this policy to decide how the new active port will be chosen and how recovery will be
                  handled.  The possible values are always, better, and failure.

         • resend-igmp (scalar)

                  In modes balance-rr, active-backup, balance-tlb and balance-alb, a failover  can  switch  IGMP
                  traffic from one port to another.

                  This  parameter  specifies  how  many  IGMP membership reports are issued on a failover event.
                  Values range from 0 to 255.  0 disables sending  membership  reports.   Otherwise,  the  first
                  membership report is sent on failover and subsequent reports are sent at 200ms intervals.

         • learn-packet-interval (scalar)

                  Specify  the  interval  between  sending  learning  packets  to each port.  The value range is
                  between 1 and 0x7fffffff.  The default value is 1.  This option only affects  balance-tlb  and
                  balance-alb    modes.     Using    the   networkd   renderer,   this   field   maps   to   the
                  LearnPacketIntervalSec= property.   If  no  time  suffix  is  specified,  the  value  will  be
                  interpreted as seconds.

         • primary (scalar)

                  Specify  a  device  to be used as a primary port, or preferred device to use as a port for the
                  bond (i.e.  the preferred device to send data through), whenever it is available.   This  only
                  affects active-backup, balance-alb, and balance-tlb modes.

   Properties for device type tunnels:
       Status: Optional.

       Purpose: Use the tunnels key to create virtual tunnel interfaces.

       Structure:  The  key  consists  of  a  mapping  of  tunnel  interface  names.   Each  tunnel requires the
       identification of the tunnel mode (see the section mode below for the  list  of  supported  modes).   The
       general configuration structure for Tunnels is shown below.

              network:
                tunnels:
                  tunnel0:
                    mode: SCALAR
                    ...

       When  applied,  a  virtual interface called tunnel0 will be created in the system.  Its operation mode is
       defined by the property mode.

       Tunnels allow traffic to pass as if it was between systems on the same local  network,  although  systems
       may be far from each other but reachable via the Internet.  They may be used to support IPv6 traffic on a
       network where the ISP does not provide the service, or to extend and "connect" separate  local  networks.
       Please see <https://en.wikipedia.org/wiki/Tunneling_protocol> for more general information about tunnels.

       The specific settings for tunnels are defined below.

       • mode (scalar)

                Defines  the  tunnel  mode.  Valid options are sit, gre, ip6gre, ipip, ipip6, ip6ip6, vti, vti6,
                wireguard, vxlan, gretap and ip6gretap modes.  In addition, the NetworkManager backend  supports
                isatap tunnels.

       • local (scalar)

                Defines  the  address of the local endpoint of the tunnel.  (For VXLAN) This should match one of
                the parent's IP addresses or make use of the networkd special values.

       • remote (scalar)

                Defines the address of the remote endpoint of the tunnel  or  multicast  group  IP  address  for
                VXLAN.

       • ttl (scalar) – since 0.103

                Defines the Time To Live (TTL) of the tunnel.  Takes a number in the range 1..255.

       • key (scalar or mapping)

                Define  keys to use for the tunnel.  The key can be a number or a dotted quad (an IPv4 address).
                For wireguard it can be a base64-encoded private key or (as of networkd v242+) an absolute  path
                to  a  file,  containing  the  private  key  (since 0.100).  It is used for identification of IP
                transforms.  This is only required for vti and vti6 when using the networkd backend.

                This field may be used as a scalar (meaning that a single key is specified and to  be  used  for
                input,   output   and   private   key),   or  as  a  mapping,  where  you  can  further  specify
                input/output/private.

         • input (scalar)

                  The input key for the tunnel

         • output (scalar)

                  The output key for the tunnel

         • private (scalar) – since 0.100

                  A base64-encoded private key  required  for  WireGuard  tunnels.   When  the  systemd-networkd
                  backend  (v242+)  is  used, this can also be an absolute path to a file containing the private
                  key.

       • keys (scalar or mapping)

                Alternate name for the key field.  See above.

         Examples:

                network:
                  tunnels:
                    tun0:
                      mode: gre
                      local: ...
                      remote: ...
                      keys:
                        input: 1234
                        output: 5678

                network:
                  tunnels:
                    tun0:
                      mode: vti6
                      local: ...
                      remote: ...
                      key: 59568549

                network:
                  tunnels:
                    wg0:
                      mode: wireguard
                      addresses: [...]
                      peers:
                        - keys:
                            public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
                            shared: /path/to/shared.key
                          ...
                      key: mNb7OIIXTdgW4khM7OFlzJ+UPs7lmcWHV7xjPgakMkQ=

                network:
                  tunnels:
                    wg0:
                      mode: wireguard
                      addresses: [...]
                      peers:
                        - keys:
                            public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
                          ...
                      keys:
                        private: /path/to/priv.key

       WireGuard specific keys:

       • mark (scalar) – since 0.100

                Firewall mark for outgoing WireGuard packets from this interface, optional.

       • port (scalar) – since 0.100

                UDP port to listen at or auto.  Optional, defaults to auto.

       • peers (sequence of mappings) – since 0.100

                A list of peers, each having keys documented below.

         Example:

                network:
                  tunnels:
                    wg0:
                      mode: wireguard
                      key: /path/to/private.key
                      mark: 42
                      port: 5182
                      peers:
                        - keys:
                            public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
                          allowed-ips: [0.0.0.0/0, "2001:fe:ad:de:ad:be:ef:1/24"]
                          keepalive: 23
                          endpoint: 1.2.3.4:5
                        - keys:
                            public: M9nt4YujIOmNrRmpIRTmYSfMdrpvE7u6WkG8FY8WjG4=
                            shared: /some/shared.key
                          allowed-ips: [10.10.10.20/24]
                          keepalive: 22
                          endpoint: 5.4.3.2:1

         • endpoint (scalar) – since 0.100

                  Remote endpoint IPv4/IPv6 address or a hostname, followed by a colon and a port number.

         • allowed-ips (sequence of scalars) – since 0.100

                  A list of IP (v4 or v6) addresses with CIDR masks from which this  peer  is  allowed  to  send
                  incoming  traffic  and  to  which  outgoing  traffic for this peer is directed.  The catch-all
                  0.0.0.0/0 may be specified for matching all IPv4 addresses, and  ::/0  may  be  specified  for
                  matching all IPv6 addresses.

         • keepalive (scalar) – since 0.100

                  An  interval  in seconds, between 1 and 65535 inclusive, of how often to send an authenticated
                  empty packet to the peer for the purpose of keeping a stateful firewall or NAT  mapping  valid
                  persistently.  Optional.

         • keys (mapping) – since 0.100

                  Define keys to use for the WireGuard peers.

                  This field can be used as a mapping, where you can further specify the public and shared keys.

           • public (scalar) – since 0.100

                    A base64-encoded public key, required for WireGuard peers.

           • shared (scalar) – since 0.100

                    A  base64-encoded  preshared  key.  Optional for WireGuard peers.  When the systemd-networkd
                    backend (v242+) is used, this can also  be  an  absolute  path  to  a  file  containing  the
                    preshared key.

       VXLAN specific keys:

       • id (scalar) – since 0.105

                The  VXLAN  Network  Identifier  (VNI  or  VXLAN  Segment  ID).   Takes  a  number  in the range
                1..16777215.

       • link (scalar) – since 0.105

                netplan ID of the parent device definition to which this VXLAN gets connected.

       • type-of-service (scalar) – since 0.105

                The Type Of Service byte value for a vxlan interface.

       • mac-learning (scalar) – since 0.105

                Takes a boolean.  When true, enables dynamic MAC learning to discover remote MAC addresses.

       • ageing, aging (scalar) – since 0.105

                The lifetime of Forwarding Database entry learned by the kernel, in seconds.

       • limit (scalar) – since 0.105

                Configures maximum number of FDB entries.

       • arp-proxy (scalar) – since 0.105

                Takes a boolean.  When true, bridge-connected VXLAN tunnel endpoint answers  ARP  requests  from
                the  local  bridge  on  behalf  of  remote  Distributed Overlay Virtual Ethernet (DOVE) clients.
                Defaults to false.

       • notifications (sequence of scalars) – since 0.105

                Takes the flags l2-miss and l3-miss to enable netlink LLADDR  and/or  netlink  IP  address  miss
                notifications.

       • short-circuit (scalar) – since 0.105

                Takes a boolean.  When true, route short circuiting is turned on.

       • checksums (sequence of scalars) – since 0.105

                Takes  the flags udp, zero-udp6-tx, zero-udp6-rx, remote-tx and remote-rx to enable transmitting
                UDP  checksums  in  VXLAN/IPv4,  send/receive  zero   checksums   in   VXLAN/IPv6   and   enable
                sending/receiving checksum offloading in VXLAN.

       • extensions (sequence of scalars) – since 0.105

                Takes  the  flags group-policy and generic-protocol to enable the "Group Policy" and/or "Generic
                Protocol" VXLAN extensions.

       • port (scalar) – since 0.105

                Configures the default destination UDP port.  If the destination  port  is  not  specified  then
                Linux kernel default will be used.  Set to 4789 to get the IANA assigned value.

       • port-range (sequence of scalars) – since 0.105

                Configures the source port range for the VXLAN.  The kernel assigns the source UDP port based on
                the flow to help the receiver to do load balancing.  When this option is  not  set,  the  normal
                range of local UDP ports is used.  Uses the form [LOWER, UPPER].

       • flow-label (scalar) – since 0.105

                Specifies the flow label to use in outgoing packets.  The valid range is 0-1048575.

       • do-not-fragment (scalar) – since 0.105

                Allows  setting  the  IPv4 Do not Fragment (DF) bit in outgoing packets.  Takes a boolean value.
                When unset, the kernel's default will be used.

   Properties for device type vlans:
       Status: Optional.

       Purpose: Use the vlans key to create VLAN interfaces.

       Structure: The key consists of a mapping of VLAN interface names.  The interface used in the link  option
       (enp5s0  in  the  example  below)  must  also  be  defined  in  the  Netplan  configuration.  The general
       configuration structure for Vlans is shown below.

              network:
                vlans:
                  vlan123:
                    id: 123
                    link: enp5s0
                    dhcp4: yes

       The specific settings for VLANs are defined below.

       • id (scalar)

                VLAN ID, a number between 0 and 4094.

       • link (scalar)

                netplan ID of the underlying device definition on which this VLAN gets created.

       Example:

              network:
                ethernets:
                  eno1: {...}
                vlans:
                  en-intra:
                    id: 1
                    link: eno1
                    dhcp4: yes
                  en-vpn:
                    id: 2
                    link: eno1
                    addresses: [...]

   Properties for device type vrfs:
       Status: Optional.

       Purpose: Use the vrfs key to create Virtual Routing and Forwarding (VRF) interfaces.

       Structure: The key consists of a mapping of VRF interface names.  The interface used in the  link  option
       (enp5s0  in  the  example  below)  must  also  be  defined  in  the  Netplan  configuration.  The general
       configuration structure for VRFs is shown below.

              network:
                renderer: networkd
                vrfs:
                  vrf1:
                    table: 1
                    interfaces:
                      - enp5s0
                    routes:
                      - to: default
                        via: 10.10.10.4
                    routing-policy:
                      - from: 10.10.10.42

       • table (scalar) – since 0.105

                The numeric routing table identifier.  This setting is compulsory.

       • interfaces (sequence of scalars) – since 0.105

                All devices matching this ID list will be added to the VRF.  This may be an empty list, in which
                case the VRF will be brought online with no member interfaces.

       • routes (sequence of mappings) – since 0.105

                Configure static routing for the device; see the Routing section.  The table value is implicitly
                set to the VRF's table.

       • routing-policy (sequence of mappings) – since 0.105

                Configure policy routing for the device; see the Routing section.  The table value is implicitly
                set to the VRF's table.

       Example:

              network:
                vrfs:
                  vrf20:
                    table: 20
                    interfaces: [ br0 ]
                    routes:
                      - to: default
                        via: 10.10.10.3
                    routing-policy:
                      - from: 10.10.10.42
                  [...]
                bridges:
                  br0:
                    interfaces: []

   Properties for device type nm-devices:
       Status: Optional.  Its use is not recommended.

       Purpose:  Use  the  nm-devices  key to configure device types that are not supported by Netplan.  This is
       NetworkManager specific configuration.

       Structure: The key consists of a mapping of NetworkManager connections.  The nm-devices  device  type  is
       for  internal  use only and should not be used in normal configuration files.  It enables a fallback mode
       for unsupported settings, using the passthrough mapping.  The  general  configuration  structure  for  NM
       connections is shown below.

              network:
                version: 2
                nm-devices:
                  NM-db5f0f67-1f4c-4d59-8ab8-3d278389cf87:
                    renderer: NetworkManager
                    networkmanager:
                      uuid: "db5f0f67-1f4c-4d59-8ab8-3d278389cf87"
                      name: "myvpnconnection"
                      passthrough:
                        connection.type: "vpn"
                        vpn.ca: "path to ca.crt"
                        vpn.cert: "path to client.crt"
                        vpn.cipher: "AES-256-GCM"
                        vpn.connection-type: "tls"
                        vpn.dev: "tun"
                        vpn.key: "path to client.key"
                        vpn.remote: "1.2.3.4:1194"
                        vpn.service-type: "org.freedesktop.NetworkManager.openvpn"

   Backend-specific configuration parameters
       In  addition  to  the other fields available to configure interfaces, some backends may require to record
       some  of  their  own  parameters  in  netplan,  especially  if  the  netplan  definitions  are  generated
       automatically by the consumer of that backend.  Currently, this is only used with NetworkManager.

       • networkmanager (mapping) – since 0.99

                Keeps  the  NetworkManager-specific  configuration  parameters  used  by the daemon to recognize
                connections.

         • name (scalar) – since 0.99

                  Set the display name for the connection.

         • uuid (scalar) – since 0.99

                  Defines the UUID (unique identifier) for  this  connection,  as  generated  by  NetworkManager
                  itself.

         • stable-id (scalar) – since 0.99

                  Defines  the  stable ID (a different form of a connection name) used by NetworkManager in case
                  the name of the connection might otherwise change, such as when  sharing  connections  between
                  users.

         • device (scalar) – since 0.99

                  Defines the interface name for which this connection applies.

         • passthrough (mapping) – since 0.102

                  Can be used as a fallback mechanism to missing keyfile settings.

SEE ALSO

       netplan-generate(8),  netplan-apply(8),  netplan-try(8), netplan-get(8), netplan-set(8), netplan-info(8),
       netplan-ip(8),    netplan-rebind(8),     netplan-status(8),     netplan-dbus(8),     systemd-networkd(8),
       NetworkManager(8)

AUTHORS

       Mathieu  Trudel-Lapierre  (<cyphermox@ubuntu.com>); Martin Pitt (<martin.pitt@ubuntu.com>); Lukas Märdian
       (<slyon@ubuntu.com>).

                                                                                           YAML configuration(5)