NAME

     gnunet-vpn — manually setup a GNUnet VPN tunnel

SYNOPSIS

     gnunet-vpn [-4 | --ipv4] [-6 | --ipv6] [-c FILENAME | --config=FILENAME] [-d TIME | --duration TIME]
                [-h | --help] [-i IP | --ip IP] [-L LOGLEVEL | --loglevel=LOGLEVEL] [-p PEERID | --peer=PEERID]
                [-s NAME | --service=NAME] [-t | --tcp] [-u | --udp] [-V | --verbose] [-v | --version]

DESCRIPTION

     gnunet-vpn can be used to manually setup a VPN tunnel via the GNUnet network.  There are two main types of
     tunnels.  Tunnels to an exit node which routes the traffic to the global Internet, and tunnels to a node
     that runs a service only within GNUnet.  Depending on the type of tunnel, gnunet-vpn takes different
     options.  The -i option is required for tunnels to an exit node, whereas the -p and -s options in
     conjunction with either -u or -t are required for tunnels to services.  For exit tunnels, both UDP and TCP
     traffic will be redirected.  For service tunnels, either UDP (-u) or TCP (-t) traffic will be redirected.
     The tool will display the IP address for this end of the tunnel.  The address can be displayed as soon as
     it has been allocated, or only after (-a) the tunnel has been created.

     -4 | --ipv4
             Desired IP address on this end of the tunnel should be an IPv4 address.

     -6 | --ipv6
             Desired IP address on this end of the tunnel should be an IPv6 address.

     -c FILENAME | --config=FILENAME
             Use the configuration file FILENAME.

     -d TIME | --duration TIME
             The mapping should be established for TIME.  The value given must be a number followed by a space
             and a time unit, for example "500 ms".  Note that the quotes are required on the shell.  The
             default value is 5 minutes.

     -h | --help
             Print short help on options.

     -i IP | --ip IP
             Tunnel should be to an exit node and connect to the given IPv4 or IPv6 IP address.  Note that you
             can specify an IPv6 address as the target here, even in combination with "-4" (4to6) and similarly
             you can specify an IPv4 address in combination with "-6" (6to4).

     -L LOGLEVEL | --loglevel=LOGLEVEL
             Use LOGLEVEL for logging.  Valid values are DEBUG, INFO, WARNING and ERROR.

     -p PEERID | --peer=PEERID
             Name of the peer offering the service to connect to.  Cannot be used in conjunction with -i,
             requires -s.

     -s NAME | --service=NAME
             Name of the service running on the target peer.  Cannot be used in conjunction with -i, requires
             -p.

     -t | --tcp
             Service runs TCP.  Either -t or -u must be specified when using -s.

     -u | --udp
             Service runs UDP.  Either -t or -u must be specified when using -s.

     -V | --verbose
             Be verbose.

     -v | --version
             Print GNUnet version number.

SEE ALSO

     gnunet-setup(1)

     The full documentation for gnunet is maintained as a Texinfo manual.  If the info(1) and gnunet programs
     are properly installed at your site, the command

           info gnunet

     should give you access to the complete handbook,

           info gnunet-c-tutorial

     will give you access to a tutorial for developers.

     Depending on your installation, this information is also available in gnunet(7) and gnunet-c-tutorial(7).

BUGS

     Report bugs by using https://bugs.gnunet.org or by sending electronic mail to ⟨gnunet-developers@gnu.org⟩.