NAME

       ifstat - Report InterFace STATistics

SYNOPSIS

       ifstat [-a] [-l] [-z] [-n] [-v] [-h] [-t] [-i if0,if1,...] [-d drv[:opt]] [-s
       [comm@][#]host[/nn]] [-T] [-A] [-w] [-W] [-S] [-b] [-q] [delay[/delay] [count]]

DESCRIPTION

       Ifstat is a little tool to report interface activity, just like iostat/vmstat do for other
       system statistics.

OPTIONS

       ifstat accepts the following options:

       -l  Enables monitoring of loopback interfaces for which statistics are available. By
           default, ifstat monitors all non-loopback interfaces that are up.

       -a  Enables monitoring of all interfaces found for which statistics are available.

       -z  Hides interface which counters are null, eg interfaces that are up but not used.

       -i  Specifies the list of interfaces to monitor, separated by commas (if an interface name
           has a comma, it can be escaped with '\'). Multiple instances of the options are added
           together.

       -s  Equivalent to -d snmp:[comm@][#]host[/nn]] to poll a remote host through SNMP. See
           below for details.

       -h  Displays a short help message.

       -n  Turns off displaying the header periodically.

       -t  Adds a timestamp at the beginning of each line.

       -T  Reports total bandwith for all monitored interfaces.

       -A  Disables use of interface indexes: by default, when polling mechanism is index based
           (snmp, ifmib), ifstat remembers indexes of monitored interfaces to poll only them.
           However, if interfaces indexes change often (new interfaces added, etc), you might
           loose some stats, hence this flag. Note that if you ask ifstat to monitor a non
           existent interface, it will poll all interfaces until it finds the requested one
           (regardless of this flag) so you can poll for an interface that goes up and down.

       -w  Uses fixed width columns, instead of enlarging them if needed for interfaces names to
           fit.

       -W  Wrap lines that are larger than the terminal width (implies -w). Wrapped lines are
           prefixed with a cycling letter to ease reading.

       -S  Keep stats updated on the same line if possible (no scrolling nor wrapping).

       -b  Reports bandwith in kbits/sec instead of kbytes/sec.

       -q  Quiet mode, warnings are not printed.

       -v  Displays version and the compiled-in drivers.

       -d  Specifies a driver to use to gather stats and an eventual option for this driver
           separated of the driver name by a colon. If this is not specified, ifstat uses the
           first driver compiled in, with no options.

           The following drivers are available (depending on the operating system and compile-
           time options, not all of them might be present):

           proc
               This driver gets statistics from Linux's /proc/net/dev file. An alternate file
               name to get stats from can be passed as the option.

           ifmib
               This driver gets statistics from FreeBSD's ifmib sysctl. It doesn't accept any
               options.

           kstat
               This driver gets statistics from Solaris kstat interface. It doesn't accept any
               options.

           ifdata
               This driver gets statistics using SIOCGIFDATA ioctl under IRIX and OpenBSD
               (different semantics). It doesn't accept any options.

           route
               This driver gets statistics using routing sysctl on BSD based systems. It doesn't
               accept any options.

           kvm This driver gets statistics by reading the kernel live structures. It accepts an
               option specifying which files/devices to use in the following format :
               [execfile][,[corefile][,swapfile]] (see kvm_open(3) for details on those fields).
               If a null string is passed for a parameter, the system default will be used for
               it.

               Note that for this driver to work, ifstat needs to have read access to the system
               memory device. This is usually done by running it as root, or by installing setgid
               mem or kmem. ifstat will NOT install setgid by default; It is up to you to decide
               if you trust it.

           dlpi
               This driver gets statistics using the DLPI streams interface available on HP-UX.
               An alternate device to query statistics from can be passed as the option (default
               is /dev/dlpi).

           win32
               This driver gets statistics using the GetIfTable interface available on Win32
               systems. It doesn't accept any options.

           snmp
               This driver gets statistics through SNMP. The option, in the form
               [comm@][#]host[/nn]], specifies the host and eventual community to poll. Default
               community is public, but can be changed by prepending "comm@" to the hostname. If
               host starts by a #, interface names are generated from their index as `ifNN' (this
               is a workaround for some equipments that give all interfaces the same
               description). Default host is localhost, and this will be used by default if snmp
               is the only available driver.

               The driver will try to poll several interfaces at once by grouping requests in
               SNMP packets. By default interfaces will be polled by group of 8. If this doesn't
               work well with your equipments, you can lower that number by suffixing the
               hostname with /nn, where nn is the number of interfaces to poll at once. You can
               also increase the number if you want to poll a large number of interfaces
               efficiently and if your server supports it.

       delay
           delay is the delay between updates in seconds, which defaults to 1.  A decimal number
           can be specified for intervals shorter than a second. (minimum 0.1)

           A second delay can also be specified (separated from the first one by a '/'). In that
           case the first delay will be used for the first poll after start and the second one
           will be used for all following polls (This can be used to have a "fast" start when
           running for a long while with a big delay).

       count
           count is the number of updates before stopping. If not specified, it is unlimited.

SEE ALSO

       vmstat(1), iostat(1)

AUTHOR

       Gaël Roualland, <gael.roualland@dial.oleane.com>