NAME

       pyocd-gdbserver - ARM Cortex-M programming tool

DESCRIPTION

       pyocd-gdbserver is an ARM Cortex-M programming tool

   Summary
       pyOCD  is  an  Open Source python based library for programming and debugging ARM Cortex-M
       microcontrollers using CMSIS-DAP.

       Includes support for flashing new binaries,  resetting  the  device,  halt,  step,  resume
       read/write memory and set/remove breakpoints.

   Support
       Firmware  files included in the upstream source are NOT included in the Debian package due
       to  a  lack  of  source  code.  Target   files   can   be   downloaded   separately   from
       https://github.com/mbedmicro/pyOCD/tree/master/binaries

       Available   targets  for  use  with  --target  option:  lpc824,  kinetis,  w7500,  kv11z7,
       lpc4088qsb,  kv10z7,  k20d50m,  ncs36510,  kl28z,  kl25z,  k82f25615,  k28f15,  maxwsnenv,
       max32600mbed,  k22fa12,  lpc4088,  lpc4330, ke18f16, kl46z, stm32f103rc, kl82z7, lpc54114,
       kl43z4,  kl26z,  lpc11xx_32,  lpc800,  rtl8195am,  kl05z,  lpc1768,   kw41z4,   lpc4088dm,
       stm32f051,  cortex_m,  lpc11u24,  kl02z, kw01z4, k64f, k22f, ke15z7, nrf51, nrf52, kl27z4,
       kw40z4, k66f18

   Usage
       usage: pyocd-gdbserver [-h] [--version] [-p PORT_NUMBER] [-T TELNET_PORT] [--allow-remote]
       [-b BOARD_ID] [-l] [--list-targets]
              [--json]  [-d  LEVEL]  [-t  TARGET] [-n] [-r] [-C VECTOR_CATCH] [-s] [-f FREQUENCY]
              [-o] [-bh] [-ce | -se] [-u] [-hp] [-fp] [-S] [-G] [-c CMD [CMD  ...]]  [-da  DAPARG
              [DAPARG ...]]

       PyOCD GDB Server

       optional arguments:

              -h, --help
                     show this help message and exit

              --version
                     show program's version number and exit

              -p PORT_NUMBER, --port PORT_NUMBER
                     Write the port number that GDB server will open.

              -T TELNET_PORT, --telnet-port TELNET_PORT
                     Specify the telnet port for semihosting.

              --allow-remote
                     Allow remote TCP/IP connections (default is no).

              -b BOARD_ID, --board BOARD_ID
                     Connect to board by board id. Use -l to list all connected boards.

              -l, --list
                     List all connected boards.

              --list-targets
                     List all available targets.

              --json Output lists in JSON format. Only applies to --list and --list-targets.

              -d LEVEL, --debug LEVEL
                     Set  the level of system logging output. Supported choices are: debug, info,
                     warning, critical, error

              -t TARGET, --target TARGET
                     Override target to debug. -n, --nobreak         Disable  halt  at  hardfault
                     handler. (Deprecated)

              -r, --reset-break
                     Halt the target when reset. (Deprecated)

              -C  VECTOR_CATCH,  --vector-catch  VECTOR_CATCH  Enable  vector  catch sources, one
              letter per enabled source in any order, or 'all' or 'none'. (h=hard
                     fault, b=bus fault, m=mem  fault,  i=irq  err,  s=state  err,  c=check  err,
                     p=nocp, r=reset, a=all, n=none).  (Default is hard fault.)

              -s, --step-int
                     Allow single stepping to step into interrupts.

              -f FREQUENCY, --frequency FREQUENCY
                     Set the SWD clock frequency in Hz.

              -o, --persist
                     Keep GDB server running even after remote has detached.

              -bh, --soft-bkpt-as-hard
                     Replace software breakpoints with hardware breakpoints.

              -ce, --chip_erase
                     Use chip erase when programming.

              -se, --sector_erase
                     Use sector erase when programming.

              -u, --unlock
                     Unlock the device.

              -hp, --hide_progress
                     Don't display programming progress.

              -fp, --fast_program
                     Use only the CRC of each page to determine if it already has the same data.

              -S, --semihosting
                     Enable semihosting.

              -G, --gdb-syscall
                     Use GDB syscalls for semihosting file I/O.

              -c CMD [CMD ...], --command CMD [CMD ...]    Run command (OpenOCD compatibility).

              -da  DAPARG  [DAPARG ...], --daparg DAPARG [DAPARG ...]   Send setting to DAPAccess
              layer.

COPYRIGHT

       2006-2013 ARM Limited