Ubuntu Manpage: stilts-tapresume - Resumes a previous query to a Table Access Protocol server

NAME

       stilts-tapresume - Resumes a previous query to a Table Access Protocol server

SYNOPSIS

       stilts tapresume [joburl=<url-value>] [compress=true|false] [poll=<millisec>]
                        [progress=true|false] [delete=finished|never|always|now] [ocmd=<cmds>]
                        [omode=out|meta|stats|count|checksum|cgi|discard|topcat|samp|tosql|gui]
                        [out=<out-table>] [ofmt=<out-format>]

DESCRIPTION

       tapresume can resume monitoring and data  retrieval  from  an  asynchronous  Table  Access
       Protocol  query  which  has already been submitted. TAP is a Virtual Observatory protocol.
       Such a pre-existing query may have been submitted by  the  tapquery  command  or  by  some
       completely  different  mechanism. It essentially does the same job as tapquery but without
       the job submission stage. It waits until the query has completed, and then  retrieves  the
       table result and processes it in accordance with the supplied parameters. The query may or
       may not be deleted from the server as part of the operation.

OPTIONS

joburl=<url-value>
The URL of a job created by submission of a TAP query which was created earlier and
has not yet been deleted (by the client) or destroyed (by the server). This will
usually be of the form <tap-url>/async/<job-id>. You can also find out, and
possibly retrieve results from the job by pointing a web browser at this URL.

compress=true|false
If true, the service is requested to provide HTTP-level compression for the
response stream (Accept-Encoding header is set to "gzip", see RFC 2616). This does
not guarantee that compression will happen but if the service honours this request
it may result in a smaller amount of network traffic at the expense of more
processing on the server and client.

poll=<millisec>
Interval to wait between polling attempts, in milliseconds. Asynchronous TAP
queries can only find out when they are complete by repeatedly polling the server
to find out the job's status. This parameter allows you to set how often that
happens. Attempts to set it too low (<50) will be rejected on the assumption that
you're thinking in seconds.

progress=true|false
If this parameter is set true, progress of the job is reported to standard output
as it happens.

delete=finished|never|always|now
Determines under what circumstances the UWS job is to be deleted from the server
when its data is no longer required. If it is not deleted, then the job is left on
the TAP server and it can be accessed via the normal UWS REST endpoints or using
tapresume until it is destroyed by the server.

Possible values:

* finished: delete only if the job finished, successfully or not

* never: do not delete

* always: delete on command exit

* now: delete and return immediately

ocmd=<cmds>
Specifies processing to be performed on the output table, after all other
processing has taken place. The value of this parameter is one or more of the
filter commands described in SUN/256. If more than one is given, they must be
separated by semicolon characters (";"). This parameter can be repeated multiple
times on the same command line to build up a list of processing steps. The sequence
of commands given in this way defines the processing pipeline which is performed on
the table.

Commands may alteratively be supplied in an external file, by using the indirection
character '@'. Thus a value of "@filename" causes the file filename to be read for
a list of filter commands to execute. The commands in the file may be separated by
newline characters and/or semicolons, and lines which are blank or which start with
a '#' character are ignored.

omode=out|meta|stats|count|checksum|cgi|discard|topcat|samp|tosql|gui
The mode in which the result table will be output. The default mode is out, which
means that the result will be written as a new table to disk or elsewhere, as
determined by the out and ofmt parameters. However, there are other possibilities,
which correspond to uses to which a table can be put other than outputting it, such
as displaying metadata, calculating statistics, or populating a table in an SQL
database. For some values of this parameter, additional parameters (<mode-args>)
are required to determine the exact behaviour.

Possible values are

* out

* meta

* stats

* count

* checksum

* cgi

* discard

* topcat

* samp

* tosql

* gui
Use the help=omode flag or see SUN/256 for more information.

out=<out-table>
The location of the output table. This is usually a filename to write to. If it is
equal to the special value "-" (the default) the output table will be written to
standard output.

This parameter must only be given if omode has its default value of "out".

ofmt=<out-format>
Specifies the format in which the output table will be written (one of the ones in
SUN/256 - matching is case-insensitive and you can use just the first few letters).
If it has the special value "(auto)" (the default), then the output filename will
be examined to try to guess what sort of file is required usually by looking at the
extension. If it's not obvious from the filename what output format is intended, an
error will result.