NAME

       strings - print the sequences of printable characters in files

SYNOPSIS

       strings [-afovV] [-min-len]
               [-n min-len] [--bytes=min-len]
               [-t radix] [--radix=radix]
               [-e encoding] [--encoding=encoding]
               [-U method] [--unicode=method]
               [-] [--all] [--print-file-name]
               [-T bfdname] [--target=bfdname]
               [-w] [--include-all-whitespace]
               [-s] [--output-separator sep_string]
               [--help] [--version] file...

DESCRIPTION

       For each file given, GNU strings prints the printable character sequences that are at
       least 4 characters long (or the number given with the options below) and are followed by
       an unprintable character.

       Depending upon how the strings program was configured it will default to either displaying
       all the printable sequences that it can find in each file, or only those sequences that
       are in loadable, initialized data sections.  If the file type is unrecognizable, or if
       strings is reading from stdin then it will always display all of the printable sequences
       that it can find.

       For backwards compatibility any file that occurs after a command-line option of just -
       will also be scanned in full, regardless of the presence of any -d option.

       strings is mainly useful for determining the contents of non-text files.

OPTIONS

       -a
       --all
       -   Scan the whole file, regardless of what sections it contains or whether those sections
           are loaded or initialized.  Normally this is the default behaviour, but strings can be
           configured so that the -d is the default instead.

           The - option is position dependent and forces strings to perform full scans of any
           file that is mentioned after the - on the command line, even if the -d option has been
           specified.

       -d
       --data
           Only print strings from initialized, loaded data sections in the file.  This may
           reduce the amount of garbage in the output, but it also exposes the strings program to
           any security flaws that may be present in the BFD library used to scan and load
           sections.  Strings can be configured so that this option is the default behaviour.  In
           such cases the -a option can be used to avoid using the BFD library and instead just
           print all of the strings found in the file.

       -f
       --print-file-name
           Print the name of the file before each string.

       --help
           Print a summary of the program usage on the standard output and exit.

       -min-len
       -n min-len
       --bytes=min-len
           Print sequences of displayable characters that are at least min-len characters long.
           If not specified a default minimum length of 4 is used.  The distinction between
           displayable and non-displayable characters depends upon the setting of the -e and -U
           options.  Sequences are always terminated at control characters such as new-line and
           carriage-return, but not the tab character.

       -o  Like -t o.  Some other versions of strings have -o act like -t d instead.  Since we
           can not be compatible with both ways, we simply chose one.

       -t radix
       --radix=radix
           Print the offset within the file before each string.  The single character argument
           specifies the radix of the offset---o for octal, x for hexadecimal, or d for decimal.

       -e encoding
       --encoding=encoding
           Select the character encoding of the strings that are to be found.  Possible values
           for encoding are: s = single-7-bit-byte characters (ASCII, ISO 8859, etc., default), S
           = single-8-bit-byte characters, b = 16-bit bigendian, l = 16-bit littleendian, B =
           32-bit bigendian, L = 32-bit littleendian.  Useful for finding wide character strings.
           (l and b apply to, for example, Unicode UTF-16/UCS-2 encodings).

       -U [d|i|l|e|x|h]
       --unicode=[default|invalid|locale|escape|hex|highlight]
           Controls the display of UTF-8 encoded multibyte characters in strings.  The default
           (--unicode=default) is to give them no special treatment, and instead rely upon the
           setting of the --encoding option.  The other values for this option automatically
           enable --encoding=S.

           The --unicode=invalid option treats them as non-graphic characters and hence not part
           of a valid string.  All the remaining options treat them as valid string characters.

           The --unicode=locale option displays them in the current locale, which may or may not
           support UTF-8 encoding.  The --unicode=hex option displays them as hex byte sequences
           enclosed between <> characters.  The --unicode=escape option displays them as escape
           sequences (\uxxxx) and the --unicode=highlight option displays them as escape
           sequences highlighted in red (if supported by the output device).  The colouring is
           intended to draw attention to the presence of unicode sequences where they might not
           be expected.

       -T bfdname
       --target=bfdname
           Specify an object code format other than your system's default format.

       -v
       -V
       --version
           Print the program version number on the standard output and exit.

       -w
       --include-all-whitespace
           By default tab and space characters are included in the strings that are displayed,
           but other whitespace characters, such a newlines and carriage returns, are not.  The
           -w option changes this so that all whitespace characters are considered to be part of
           a string.

       -s
       --output-separator
           By default, output strings are delimited by a new-line. This option allows you to
           supply any string to be used as the output record separator.  Useful with
           --include-all-whitespace where strings may contain new-lines internally.

       @file
           Read command-line options from file.  The options read are inserted in place of the
           original @file option.  If file does not exist, or cannot be read, then the option
           will be treated literally, and not removed.

           Options in file are separated by whitespace.  A whitespace character may be included
           in an option by surrounding the entire option in either single or double quotes.  Any
           character (including a backslash) may be included by prefixing the character to be
           included with a backslash.  The file may itself contain additional @file options; any
           such options will be processed recursively.

SEE ALSO

       ar(1), nm(1), objdump(1), ranlib(1), readelf(1) and the Info entries for binutils.

COPYRIGHT

       Copyright (c) 1991-2022 Free Software Foundation, Inc.

       Permission is granted to copy, distribute and/or modify this document under the terms of
       the GNU Free Documentation License, Version 1.3 or any later version published by the Free
       Software Foundation; with no Invariant Sections, with no Front-Cover Texts, and with no
       Back-Cover Texts.  A copy of the license is included in the section entitled "GNU Free
       Documentation License".