Ubuntu Manpage: videogen - generate Modelines for Xorg servers

NAME

       videogen - generate Modelines for Xorg servers

SYNOPSIS


       videogen  [-v|-q]  [-fb|-nfb]  [-nv|-nnv]  [-f=<file|->]  [-m=mode]  [-mdc=n]  [-mhf=n] [-mvf=n] [-dvf=n]
         [-hv=n] [-vv=n] [-hfp=n] [-hbp=n] [-hsp=n] [-vfp=n] [-vbp=n] [-vsp=n]

DESCRIPTION

videogen generates Modelines for Xorg servers (or XFree86 servers) to reach the highest possible vertical
refresh rate at all resolutions, or to match the refresh rate you desire. As a new feature, it can obey
the non-free NVidia driver's timing constraints. It can print the calculated results in the Linux
framebuffer device format as well.

ATTENTION! You only have to specify the maximum dot clock, the maximum horizontal frequency, the maximum
vertical refresh, and of course the modes (resolutions) to generate the appropriate Modelines. The other
options are only there for tweaking or solving special problems, there are hardcoded defaults for them
which are suitable for the vast majority of cases.

CONFIGURATION FILE
A configuration file can be used to specify all or part of the parameters needed by videogen to perform
its calculations. This can be very comfortable in many cases. You can also specify a configuration file
path on the command line other than the default (~/.videogen) or read from stdin which might be helpful
if you want to call videogen from another program or from a script.

The general syntax rules are the following: parameters are specified using name=value pairs. The
parameter names are matched in a case insensitive manner. Blanks are optional. Multiple name=value pairs
can be specified on a single line separated by ";" characters. Any string after a "#" character is
treated as a comment up to the end of the line.

COMMAND LINE
The command line options always override the parameters set in the configuration file. This also applies
to the mode list, so when one or more modes are specified on the command line, the entire list of modes
read from the configuration file is replaced by these.

OPTIONS
The command line options are described below together with their configuration file variable counterparts
(if present).

-v
-q
verbose=on|off
Turn on/off verbose output. FYI -q stands for quiet ;)
(default=on)

-fb
-nfb
fbset=on|off
Turn on/off fbset (Linux framebuffer timings) mode. In this mode fbset timings are printed instead
of Modelines.
(default=off)

-nv
-nnv
nvidia=on|off
Turn on/off non-free NVidia Linux driver compatibility mode.
(default=on)

-f=filespec
Use filespec as the configuration file. This accepts - to read the options from the standard
input. The "~" character gets expanded to the home directory of the user running videogen.
(default=~/.videogen)

-m=modespec
mode=modespec
Adds modespec to the list of modes to calculate a Modeline for. This must be in the form 800x600
(width x height) and it can be specified more than once to add several modes.

-mdc=freq
Set freq to the maximum dot clock rate of your video card or the bandwidth of your monitor,
whichever is lower, in MHz.

-mhf=freq
Set freq to the maximum horizontal refresh frequency of your monitor in kHz.

-mvf=freq
Set freq to the maximum vertical refresh frequency of your monitor in Hz.

-dvf=freq
Set freq to the vertical refresh frequency which you think would be optimal for you, in Hz. The
program will try to match this frequency at all resolutions, instead of the maximum frequency that
would be technically possible. (optional)

-hv=percent
Set percent to the percentage of the horizontal frame length you want the visible resolution to
be. (optional)

-vv=percent
Set percent to the percentage of the vertical frame length you want the visible resolution to be.
(optional)

-hfp=duration
Set duration to the horizontal front porch duration of your monitor in clock ticks. (optional)

-hbp=duration
Set duration to the horizontal back porch duration of your monitor in clock ticks. (optional)

-hsp=duration
Set duration to the minimum horizontal sync pulse duration of your monitor. (optional)

-vfp=duration
Set duration to the vertical front porch duration of your monitor in clock ticks. (optional)

-vbp=duration
Set duration to the vertical back porch duration of your monitor in clock ticks. (optional)

-vsp=duration
Set duration to the minimum vertical sync pulse duration of your monitor. (optional)

ERRORS
You can expect the following error codes to be returned by videogen:

100 system error (memory allocation problems, or other)

101 command line option error

102 configuration file error

103 bad resolution error, currently returned when no (valid) modes have been specified anywhere

104 bad maximum dot clock rate, currently returned when no proper value has been specified anywhere

105 bad maximum horizontal refresh, currently returned when no proper value has been specified
anywhere

106 bad maximum vertical refresh, currently returned when no proper value has been specified anywhere

FIXED DOT CLOCKS
If your display adapter does not have a programmable clockchip then you will need to get a list of
available clocks somehow and enter these as the maximum dot clock frequency. This way videogen will have
to adjust (decrease) the horizontal refresh frequency to get exactly the given dot clock rate. A similar
method can be used to match the proper frequencies of a fixed frequency monitor.

FILES

       ~/.videogen
              The default location for the videogen configuration file.

       /etc/X11/xorg.conf
              The  Xserver configuration file where Modelines generated with videogen can be inserted. Currently
              this must be done by hand.

       /etc/X11/XF86Config
       /etc/X11/XF86Config-4
              Names of the Xserver configuration file in older releases of X.

AUTHOR

       Szabolcs Rumi <rumi_at_rtfm_dot_hu>

COPYING