Provided by: freebsd-manpages_12.2-1_all 
NAME
cd — SCSI CD-ROM driver
SYNOPSIS
device cd
DESCRIPTION
The cd driver provides support for a SCSI CD-ROM (Compact Disc-Read Only Memory) drive. In
an attempt to look like a regular disk, the cd driver synthesizes a partition table, with
one partition covering the entire CD-ROM. It is possible to modify this partition table
using disklabel(8), but it will only last until the CD-ROM is unmounted. In general the
interfaces are similar to those described by ada(4) and da(4).
As the SCSI adapter is probed during boot, the SCSI bus is scanned for devices. Any devices
found which answer as CDROM (type 5) or WORM (type 4) type devices will be `attached' to the
cd driver. Prior to FreeBSD 2.1, the first device found will be attached as cd0 the next,
cd1, etc. Beginning in FreeBSD 2.1 it is possible to specify what cd unit a device should
come on line as; refer to scsi(4) for details on kernel configuration.
The system utility disklabel(8) may be used to read the synthesized disk label structure,
which will contain correct figures for the size of the CD-ROM should that information be
required.
KERNEL CONFIGURATION
Any number of CD-ROM devices may be attached to the system regardless of system
configuration as all resources are dynamically allocated.
IOCTLS
The following ioctl(2) calls which apply to SCSI CD-ROM drives are defined in the header
files <sys/cdio.h> and <sys/disklabel.h>.
CDIOCPLAYTRACKS (struct ioc_play_track) Start audio playback given a track address and
length. The structure is defined as follows:
struct ioc_play_track
{
u_char start_track;
u_char start_index;
u_char end_track;
u_char end_index;
};
CDIOCPLAYBLOCKS (struct ioc_play_blocks) Start audio playback given a block address and
length. The structure is defined as follows:
struct ioc_play_blocks
{
int blk;
int len;
};
CDIOCPLAYMSF (struct ioc_play_msf) Start audio playback given a `minutes-seconds-
frames' address and length. The structure is defined as follows:
struct ioc_play_msf
{
u_char start_m;
u_char start_s;
u_char start_f;
u_char end_m;
u_char end_s;
u_char end_f;
};
CDIOCREADSUBCHANNEL (struct ioc_read_subchannel) Read information from the subchannel at
the location specified by this structure:
struct ioc_read_subchannel {
u_char address_format;
#define CD_LBA_FORMAT 1
#define CD_MSF_FORMAT 2
u_char data_format;
#define CD_SUBQ_DATA 0
#define CD_CURRENT_POSITION 1
#define CD_MEDIA_CATALOG 2
#define CD_TRACK_INFO 3
u_char track;
int data_len;
struct cd_sub_channel_info *data;
};
CDIOREADTOCHEADER (struct ioc_toc_header) Return summary information about the table of
contents for the mounted CD-ROM. The information is returned into the
following structure:
struct ioc_toc_header {
u_short len;
u_char starting_track;
u_char ending_track;
};
CDIOREADTOCENTRYS (struct ioc_read_toc_entry) Return information from the table of
contents entries mentioned. (Yes, this command name is misspelled.)
The argument structure is defined as follows:
struct ioc_read_toc_entry {
u_char address_format;
u_char starting_track;
u_short data_len;
struct cd_toc_entry *data;
};
The requested data is written into an area of size data_len and pointed
to by data.
CDIOCSETPATCH (struct ioc_patch) Attach various audio channels to various output
channels. The argument structure is defined thusly:
struct ioc_patch {
u_char patch[4];
/* one for each channel */
};
CDIOCGETVOL
CDIOCSETVOL (struct ioc_vol) Get (set) information about the volume settings of the
output channels. The argument structure is as follows:
struct ioc_vol
{
u_char vol[4];
/* one for each channel */
};
CDIOCSETMONO Patch all output channels to all source channels.
CDIOCSETSTEREO Patch left source channel to the left output channel and the right
source channel to the right output channel.
CDIOCSETMUTE Mute output without changing the volume settings.
CDIOCSETLEFT
CDIOCSETRIGHT Attach both output channels to the left (right) source channel.
CDIOCSETDEBUG
CDIOCCLRDEBUG Turn on (off) debugging for the appropriate device.
CDIOCPAUSE
CDIOCRESUME Pause (resume) audio play, without resetting the location of the read-
head.
CDIOCRESET Reset the drive.
CDIOCSTART
CDIOCSTOP Tell the drive to spin-up (-down) the CD-ROM.
CDIOCALLOW
CDIOCPREVENT Tell the drive to allow (prevent) manual ejection of the CD-ROM disc.
Not all drives support this feature.
CDIOCEJECT Eject the CD-ROM.
CDIOCCLOSE Tell the drive to close its door and load the media. Not all drives
support this feature.
NOTES
When a CD-ROM is changed in a drive controlled by the cd driver, then the act of changing
the media will invalidate the disklabel and information held within the kernel. To stop
corruption, all accesses to the device will be discarded until there are no more open file
descriptors referencing the device. During this period, all new open attempts will be
rejected. When no more open file descriptors reference the device, the first next open will
load a new set of parameters (including disklabel) for the drive.
The audio code in the cd driver only support SCSI-2 standard audio commands. As many CD-ROM
manufacturers have not followed the standard, there are many CD-ROM drives for which audio
will not work. Some work is planned to support some of the more common `broken' CD-ROM
drives; however, this is not yet under way.
SYSCTL VARIABLES
The following variables are available as both sysctl(8) variables and loader(8) tunables:
kern.cam.cd.retry_count
This variable determines how many times the cd driver will retry a READ or WRITE
command. This does not affect the number of retries used during probe time or for the
cd driver dump routine. This value currently defaults to 4.
kern.cam.cd.%d.minimum_cmd_size
The cd driver attempts to automatically determine whether the drive it is talking to
supports 6 byte or 10 byte MODE SENSE/MODE SELECT operations. Many SCSI drives only
support 6 byte commands, and ATAPI drives only support 10 byte commands. The cd driver
first attempts to determine whether the protocol in use typically supports 6 byte
commands by issuing a CAM Path Inquiry CCB. It will then default to 6 byte or 10 byte
commands as appropriate. After that, the cd driver defaults to using 6 byte commands
(assuming the protocol the drive speaks claims to support 6 byte commands), until one
fails with a SCSI ILLEGAL REQUEST error. Then it tries the 10 byte version of the
command to see if that works instead. Users can change the default via per-drive sysctl
variables and loader tunables. Where “%d” is the unit number of the drive in question.
Valid minimum command sizes are 6 and 10. Any value above 6 will be rounded to 10, and
any value below 6 will be rounded to 6.
FILES
/dev/cd[0-9][a-h] raw mode CD-ROM devices
DIAGNOSTICS
None.
SEE ALSO
cam(4), da(4), disklabel(8), cd(9)
HISTORY
This cd driver is based upon the cd driver written by Julian Elischer, which appeared in
386BSD 0.1. The CAM version of the cd driver was written by Kenneth Merry and first
appeared in FreeBSD 3.0.
BUGS
The names of the structures used for the third argument to ioctl() were poorly chosen, and a
number of spelling errors have survived in the names of the ioctl() commands.