Ubuntu Manpage: savage - S3 Savage video driver

Provided by: xserver-xorg-video-savage_2.3.9-4_amd64

NAME

       savage - S3 Savage video driver

SYNOPSIS

       Section "Device"
         Identifier "devname"
         Driver "savage"
         ...
       EndSection

DESCRIPTION

       savage is an Xorg driver for the S3 Savage family video accelerator chips.  2D, 3D, and Xv
       acceleration is supported  on  all  chips  except  the  Savage2000  (2D  only).   Dualhead
       operation  is  supported on MX, IX, and SuperSavage chips.  The savage driver supports PCI
       and AGP boards with the following chips:

       Savage3D        (8a20 and 8a21) (2D, 3D)

       Savage4         (8a22) (2D, 3D)

       Savage2000      (9102) (2D only)

       Savage/MX       (8c10 and 8c11) (2D, 3D, Dualhead)

       Savage/IX       (8c12 and 8c13) (2D, 3D, Dualhead)

       SuperSavage/MX  (8c22, 8c24, and 8c26) (2D, 3D, Dualhead)

       SuperSavage/IX  (8c2a, 8c2b, 8c2c, 8c2d, 8c2e, and 8c2f) (2D, 3D, Dualhead)

       ProSavage PM133 (8a25) (2D, 3D)

       ProSavage KM133 (8a26) (2D, 3D)

       Twister (ProSavage PN133)
                       (8d01) (2D, 3D)

       TwisterK (ProSavage KN133)
                       (8d02) (2D, 3D)

       ProSavage DDR   (8d03) (2D, 3D)

       ProSavage DDR-K (8d04) (2D, 3D)

CONFIGURATION DETAILS

Please refer to xorg.conf(5) for general configuration details. This section only covers
configuration details specific to this driver.

The following driver Options are supported:

Option "HWCursor" "boolean"

Option "SWCursor" "boolean"
These two options interact to specify hardware or software cursor. If the SWCursor
option is specified, any HWCursor setting is ignored. Thus, either "HWCursor off"
or "SWCursor on" will force the use of the software cursor. On Savage/MX and
Savage/IX chips which are connected to LCDs, a software cursor will be forced,
because the Savage hardware cursor does not correctly track the automatic panel
expansion feature. Default: hardware cursor.

Option "NoAccel" "boolean"
Disable or enable acceleration. Default: acceleration is enabled.

Option "AccelMethod" "string"
Chooses between available acceleration architectures. Valid options are XAA and
EXA. XAA is the traditional acceleration architecture and support for it is very
stable. EXA is a newer acceleration architecture with better performance for the
Render and Composite extensions, but the rendering code for it is newer and
possibly unstable. The default is XAA.

Option "Rotate" "CW"

Option "Rotate" "CCW"
Rotate the desktop 90 degrees clockwise or counterclockwise. This option forces
the ShadowFB option on, and disables acceleration and the RandR extension.
Default: no rotation.

Option "ShadowFB" "boolean"
Enable or disable use of the shadow framebuffer layer. This option disables
acceleration. Default: off.

Option "LCDClock" "frequency"
Override the maximum dot clock. Some LCD panels produce incorrect results if they
are driven at too fast of a frequency. If UseBIOS is on, the BIOS will usually
restrict the clock to the correct range. If not, it might be necessary to override
it here. The frequency parameter may be specified as an integer in Hz (135750000),
or with standard suffixes like "k", "kHz", "M", or "MHz" (as in 135.75MHz).

Option "CrtOnly" "boolean"
This option disables output to the LCD and enables output to the CRT port only. It
is useful on laptops if you only want to use the CRT port or to force the CRT
output only on desktop cards that use mobile chips. Default: auto-detect active
outputs

Option "UseBIOS" "boolean"
Enable or disable use of the video BIOS to change modes. Ordinarily, the savage
driver tries to use the video BIOS to do mode switches. This generally produces
the best results with the mobile chips (/MX and /IX), since the BIOS knows how to
handle the critical but unusual timing requirements of the various LCD panels
supported by the chip. To do this, the driver searches through the BIOS mode list,
looking for the mode which most closely matches the xorg.conf mode line. Some
purists find this scheme objectionable. If you would rather have the savage driver
use your mode line timing exactly, turn off the UseBios option. Note: Use of the
BIOS is required for dualhead operation. Default: on (use the BIOS).

Option "IgnoreEDID" "boolean"
Do not use EDID data for mode validation, but DDC is still used for monitor
detection. This is different from NoDDC option.
The default value is off.

Option "ShadowStatus" "boolean"
Enables the use of a shadow status register. There is a chip bug in the Savage
graphics engine that can cause a bus lock when reading the engine status register
under heavy load, such as when scrolling text or dragging windows. The bug affects
about 4% of all Savage users without DRI and a large fraction of users with DRI.
If your system hangs regularly while scrolling text or dragging windows, try
turning this option on. This uses an alternate method of reading the engine status
which is slightly more expensive, but avoids the problem. When DRI is enabled then
the default is "on" (use shadow status), otherwise the default is "off" (use normal
status register).

Option "DisableCOB" "boolean"
Disables the COB (Command Overflow Buffer) on savage4 and newer chips. There is
supposedly a HW cache coherency problem on certain savage4 and newer chips that
renders the COB useless. If you are having problems with 2D acceleration you can
disable the COB, however you will lose some performance. 3D acceleration requires
the COB to work. This option only applies to Savage4 and newer chips. Default:
"off" (use COB).

Option "BCIforXv" "boolean"
Use the BCI to copy and reformat Xv pixel data. Using the BCI for Xv causes
graphics artifacts on some chips. This option only applies to Savage4 and
prosavage/twister chips. On some combinations of chipsets and video players, BCI
formatting might actually be slower than software formatting ("AGPforXv" might help
in this case). BCI formatting can only be used on video data with a width that is a
multiple of 16 pixels (which is the vast majority of videos). Other widths are
handled through software formatting. Default: on for prosavage and twister (use BCI
for Xv); off for savage4 (do not use the BCI for Xv).

Option "AGPforXv" "boolean"
Instructs the BCI Xv pixel formatter to use AGP memory as a scratch buffer.
Ordinarily the BCI formatter uses a an area in framebuffer memory to hold YV12
planar data to be converted for display. This requires a somewhat expensive upload
of YV12 data to framebuffer memory. The "AGPforXv" option causes the BCI formatter
to place the YV12 data in AGP memory instead, which can be uploaded faster than the
framebuffer. Use of this option cuts upload overhead by 25% according to
benchmarks. This option also smooths out most of the shearing present when using
BCI for pixel conversion. Currently this option is experimental and is disabled by
default. Video width restrictions that apply to "BCIforXv" also apply here. Only
valid when "DRI" and "BCIforXv" are both active, and only on AGP chipsets. Default:
"off".
If "AccelMethod" is set to "EXA" and "AGPforXv" is enabled, then the driver will
also attempt to reuse the AGP scratch buffer for UploadToScreen acceleration.

Option "AGPMode" "integer"
Set AGP data transfer rate. (used only when DRI is enabled)
1 -- x1 (default)
2 -- x2
4 -- x4
others -- invalid

Option "AGPSize" "integer"
The amount of AGP memory that will allocated for DMA and textures in MB. Valid
sizes are 4, 8, 16, 32, 64, 128 and 256. The default is 16MB.

Option "DmaMode" "string"
This option influences in which way DMA (direct memory access) is used by the
kernel and 3D drivers.
Any -- Try command DMA first, then vertex DMA (default)
Command -- Only use command DMA or don't use DMA at all
Vertex -- Only use vertex DMA or don't use DMA at all
None -- Disable DMA
Command and vertex DMA cannot be enabled at the same time. Which DMA mode is
actually used in the end also depends on the DRM version (only >= 2.4.0 supports
command DMA) and the hardware (Savage3D/MX/IX doesn't support command DMA).

Option "DmaType" "string"
The type of memory that will be used by the 3D driver for DMA (direct memory
access).
PCI -- PCI memory (default on PCI cards)
AGP -- AGP memory (default on AGP cards)
"AGP" only works if you have an AGP card.

Option "BusType" "string"
The bus type that will be used to access the graphics card.
PCI -- PCI bus (default on PCI cards)
AGP -- AGP bus (default on AGP cards)
"AGP" only works if you have an AGP card. If you choose "PCI" on an AGP card the
AGP bus speed is not set and no AGP aperture is allocated. This implies DmaType
"PCI".

Option "DRI" "boolean"
Enable DRI support. This option allows you to enable or disable the DRI. Default:
"on" (enable DRI).

FILES

       savage_drv.o

AUTHORS