Ubuntu Manpage: icmp - Linux IPv4 ICMP kernel module.

NAME

       icmp - Linux IPv4 ICMP kernel module.

DESCRIPTION

This kernel protocol module implements the Internet Control Message Protocol defined in
RFC 792. It is used to signal error conditions and for diagnosis. The user doesn't
interact directly with this module; instead it communicates with the other protocols in
the kernel and these pass the ICMP errors to the application layers. The kernel ICMP
module also answers ICMP requests.

A user protocol may receive ICMP packets for all local sockets by opening a raw socket
with the protocol IPPROTO_ICMP. See raw(7) for more information. The types of ICMP
packets passed to the socket can be filtered using the ICMP_FILTER socket option. ICMP
packets are always processed by the kernel too, even when passed to a user socket.

Linux limits the rate of ICMP error packets to each destination. ICMP_REDIRECT and
ICMP_DEST_UNREACH are also limited by the destination route of the incoming packets.

/proc interfaces
ICMP supports a set of /proc interfaces to configure some global IP parameters. The
parameters can be accessed by reading or writing files in the directory
/proc/sys/net/ipv4/. Most of these parameters are rate limitations for specific ICMP
types. Linux 2.2 uses a token bucket filter to limit ICMPs. The value is the timeout in
jiffies until the token bucket filter is cleared after a burst. A jiffy is a system
dependent unit, usually 10ms on i386 and about 1ms on alpha and ia64.

icmp_destunreach_rate (Linux 2.2 to 2.4.9)
Maximum rate to send ICMP Destination Unreachable packets. This limits the rate at
which packets are sent to any individual route or destination. The limit does not
affect sending of ICMP_FRAG_NEEDED packets needed for path MTU discovery.

icmp_echo_ignore_all (since Linux 2.2)
If this value is nonzero, Linux will ignore all ICMP_ECHO requests.

icmp_echo_ignore_broadcasts (since Linux 2.2)
If this value is nonzero, Linux will ignore all ICMP_ECHO packets sent to broadcast
addresses.

icmp_echoreply_rate (Linux 2.2 to 2.4.9)
Maximum rate for sending ICMP_ECHOREPLY packets in response to ICMP_ECHOREQUEST
packets.

icmp_errors_use_inbound_ifaddr (Boolean; default: disabled; since Linux 2.6.12)
If disabled, ICMP error messages are sent with the primary address of the exiting
interface.

If enabled, the message will be sent with the primary address of the interface that
received the packet that caused the ICMP error. This is the behavior that many
network administrators will expect from a router. And it can make debugging
complicated network layouts much easier.

Note that if no primary address exists for the interface selected, then the primary
address of the first non-loopback interface that has one will be used regardless of
this setting.

icmp_ignore_bogus_error_responses (Boolean; default: disabled; since Linux 2.2)
Some routers violate RFC1122 by sending bogus responses to broadcast frames. Such
violations are normally logged via a kernel warning. If this parameter is enabled,
the kernel will not give such warnings, which will avoid log file clutter.

icmp_paramprob_rate (Linux 2.2 to 2.4.9)
Maximum rate for sending ICMP_PARAMETERPROB packets. These packets are sent when a
packet arrives with an invalid IP header.

icmp_ratelimit (integer; default: 1000; since Linux 2.4.10)
Limit the maximum rates for sending ICMP packets whose type matches icmp_ratemask
(see below) to specific targets. 0 to disable any limiting, otherwise the minimum
space between responses in milliseconds.

icmp_ratemask (integer; default: see below; since Linux 2.4.10)
Mask made of ICMP types for which rates are being limited.

Significant bits: IHGFEDCBA9876543210
Default mask: 0000001100000011000 (0x1818)

Bit definitions (see the Linux kernel source file include/linux/icmp.h):

0 Echo Reply
3 Destination Unreachable *
4 Source Quench *
5 Redirect
8 Echo Request
B Time Exceeded *
C Parameter Problem *
D Timestamp Request
E Timestamp Reply
F Info Request
G Info Reply
H Address Mask Request
I Address Mask Reply

The bits marked with an asterisk are rate limited by default (see the default mask above).

icmp_timeexceed_rate (Linux 2.2 to 2.4.9)
Maximum rate for sending ICMP_TIME_EXCEEDED packets. These packets are sent to
prevent loops when a packet has crossed too many hops.

ping_group_range (two integers; default: see below; since Linux 2.6.39)
Range of the group IDs (minimum and maximum group IDs, inclusive) that are allowed
to create ICMP Echo sockets. The default is "1 0", which means no group is allowed
to create ICMP Echo sockets.

VERSIONS

       Support for the ICMP_ADDRESS request was removed in 2.2.

       Support for ICMP_SOURCE_QUENCH was removed in Linux 2.2.

NOTES

       As many other implementations don't support IPPROTO_ICMP raw sockets, this feature  should
       not be relied on in portable programs.

       ICMP_REDIRECT  packets  are  not sent when Linux is not acting as a router.  They are also
       accepted only from the old gateway defined in the routing table and  the  redirect  routes
       are expired after some time.

       The  64-bit  timestamp  returned  by  ICMP_TIMESTAMP  is  in milliseconds since the Epoch,
       1970-01-01 00:00:00 +0000 (UTC).

       Linux ICMP internally uses a raw socket to send ICMPs.  This  raw  socket  may  appear  in
       netstat(8) output with a zero inode.

COLOPHON

       This  page  is  part of release 5.10 of the Linux man-pages project.  A description of the
       project, information about reporting bugs, and the latest version of  this  page,  can  be
       found at https://www.kernel.org/doc/man-pages/.

NAME

DESCRIPTION

VERSIONS

NOTES

SEE ALSO

COLOPHON