Provided by: anytun_0.3.8-1fakesync1_amd64 
NAME
anytun - anycast tunneling daemon
SYNOPSIS
anytun
[ -h|--help ]
[ -D|--nodaemonize ]
[ -u|--username <username> ]
[ -g|--groupname <groupname> ]
[ -C|--chroot <path> ]
[ -P|--write-pid <filename> ]
[ -L|--log <target>:<level>[,<param1>[,<param2>[..]]] ]
[ -U|--debug ]
[ -i|--interface <ip-address> ]
[ -p|--port <port> ]
[ -r|--remote-host <hostname|ip> ]
[ -o|--remote-port <port> ]
[ -4|--ipv4-only ]
[ -6|--ipv6-only ]
[ -I|--sync-interface <ip-address> ]
[ -S|--sync-port port> ]
[ -M|--sync-hosts <hostname|ip>[:<port>][,<hostname|ip>[:<port>][...]] ]
[ -X|--control-host <hostname|ip>[:<port>]
[ -d|--dev <name> ]
[ -t|--type <tun|tap> ]
[ -n|--ifconfig <local>/<prefix> ]
[ -x|--post-up-script <script> ]
[ -R|--route <net>/<prefix length> ]
[ -m|--mux <mux-id> ]
[ -s|--sender-id <sender id> ]
[ -w|--window-size <window size> ]
[ -k|--kd-prf <kd-prf type> ]
[ -e|--role <role> ]
[ -E|--passphrase <pass phrase> ]
[ -K|--key <master key> ]
[ -A|--salt <master salt> ]
[ -c|--cipher <cipher type> ]
[ -a|--auth-algo <algo type> ]
[ -b|--auth-tag-length <length> ]
DESCRIPTION
Anytun is an implementation of the Secure Anycast Tunneling Protocol (SATP). It provides a
complete VPN solution similar to OpenVPN or IPsec in tunnel mode. The main difference is
that anycast allows a setup of tunnels between an arbitrary combination of anycast,
unicast and multicast hosts.
OPTIONS
Anytun has been designed as a peer to peer application, so there is no difference between
client and server. The following options can be passed to the daemon:
-D, --nodaemonize
This option instructs Anytun to run in foreground instead of becoming a daemon which
is the default.
-u, --username <username>
run as this user. If no group is specified (-g) the default group of the user is used.
The default is to not drop privileges.
-g, --groupname <groupname>
run as this group. If no username is specified (-u) this gets ignored. The default is
to not drop privileges.
-C, --chroot <path>
Instruct Anytun to run in a chroot jail. The default is to not run in chroot.
-P, --write-pid <filename>
Instruct Anytun to write it’s pid to this file. The default is to not create a pid
file.
-L, --log <target>:<level>[,<param1>[,<param2>[..]]]
add log target to logging system. This can be invoked several times in order to log to
different targets at the same time. Every target hast its own log level which is a
number between 0 and 5. Where 0 means disabling log and 5 means debug messages are
enabled.
The file target can be used more the once with different levels. If no target is
provided at the command line a single target with the config syslog:3,anytun,daemon is
added.
The following targets are supported:
syslog
log to syslog daemon, parameters <level>[,<logname>[,<facility>]]
file
log to file, parameters <level>[,<path>]
stdout
log to standard output, parameters <level>
stderr
log to standard error, parameters <level>
-U, --debug
This option instructs Anytun to run in debug mode. It implicits -D (don’t daemonize)
and adds a log target with the configuration stdout:5 (logging with maximum level). In
future releases there might be additional output when this option is supplied.
-i, --interface <ip address>
This IP address is used as the sender address for outgoing packets. In case of anycast
tunnel endpoints, the anycast IP has to be used. In case of unicast endpoints, the
address is usually derived correctly from the routing table. The default is to not use
a special interface and just bind on all interfaces.
-p, --port <port>
The local UDP port that is used to send and receive the payload data. The two tunnel
endpoints can use different ports. If a tunnel endpoint consists of multiple anycast
hosts, all hosts have to use the same port. default: 4444
-r, --remote-host <hostname|ip>
This option can be used to specify the remote tunnel endpoint. In case of anycast
tunnel endpoints, the anycast IP address has to be used. If you do not specify an
address, it is automatically determined after receiving the first data packet.
-o, --remote-port <port>
The UDP port used for payload data by the remote host (specified with -p on the remote
host). If you do not specify a port, it is automatically determined after receiving
the first data packet.
-4, --ipv4-only
Resolv to IPv4 addresses only. The default is to resolv both IPv4 and IPv6 addresses.
-6, --ipv6-only
Resolv to IPv6 addresses only. The default is to resolv both IPv4 and IPv6 addresses.
-I, --sync-interface <ip-address>
local unicast(sync) ip address to bind to
This option is only needed for tunnel endpoints consisting of multiple anycast hosts.
The unicast IP address of the anycast host can be used here. This is needed for
communication with the other anycast hosts. The default is to not use a special
interface and just bind on all interfaces. However this is only the case if
synchronisation is active see --sync-port.
-S, --sync-port <port>
local unicast(sync) port to bind to
This option is only needed for tunnel endpoints consisting of multiple anycast hosts.
This port is used by anycast hosts to synchronize information about tunnel endpoints.
No payload data is transmitted via this port. By default the synchronisation is
disabled an therefore the port is kept empty.
It is possible to obtain a list of active connections by telnetting into this port.
This port is read-only and unprotected by default. It is advised to protect this port
using firewall rules and, eventually, IPsec.
-M, --sync-hosts <hostname|ip>[:<port>],[<hostname|ip>[:<port>][...]]
remote hosts to sync with
This option is only needed for tunnel endpoints consisting of multiple anycast hosts.
Here, one has to specify all unicast IP addresses of all other anycast hosts that
comprise the anycast tunnel endpoint. By default synchronisation is disabled and
therefore this is empty. Mind that the port can be omitted in which case port 2323 is
used. If you want to specify an ipv6 address and a port you have to use [ and ] to
separate the address from the port, eg.: [::1]:1234. If you want to use the default
port [ and ] can be omitted.
-X, --control-host <hostname|ip>[:<port>]
fetch the config from this host. The default is not to use a control host and
therefore this is empty. Mind that the port can be omitted in which case port 2323 is
used. If you want to specify an ipv6 address and a port you have to use [ and ] to
separate the address from the port, eg.: [::1]:1234. If you want to use the default
port [ and ] can be omitted.
-d, --dev <name>
device name
By default, tapN is used for Ethernet tunnel interfaces, and tunN for IP tunnels,
respectively. This option can be used to manually override these defaults.
-t, --type <tun|tap>
device type
Type of the tunnels to create. Use tap for Ethernet tunnels, tun for IP tunnels.
-n, --ifconfig <local>/<prefix>
The local IP address and prefix length. The remote tunnel endpoint has to use a
different IP address in the same subnet.
<local>
the local IP address for the tun/tap device
<prefix>
the prefix length of the network
-x, --post-up-script <script>
This option instructs Anytun to run this script after the interface is created. By
default no script will be executed.
-R, --route <net>/<prefix length>
add a route to connection. This can be invoked several times.
-m, --mux <mux-id>
the multiplex id to use. default: 0
-s, --sender-id <sender id>
Each anycast tunnel endpoint needs a unique sender id (1, 2, 3, ...). It is needed to
distinguish the senders in case of replay attacks. This option can be ignored on
unicast endpoints. default: 0
-w, --window-size <window size>
seqence window size
Sometimes, packets arrive out of order on the receiver side. This option defines the
size of a list of received packets' sequence numbers. If, according to this list, a
received packet has been previously received or has been transmitted in the past, and
is therefore not in the list anymore, this is interpreted as a replay attack and the
packet is dropped. A value of 0 deactivates this list and, as a consequence, the
replay protection employed by filtering packets according to their secuence number. By
default the sequence window is disabled and therefore a window size of 0 is used.
-k, --kd—prf <kd-prf type>
key derivation pseudo random function
The pseudo random function which is used for calculating the session keys and session
salt.
Possible values:
null
no random function, keys and salt are set to 0..00
aes-ctr
AES in counter mode with 128 Bits, default value
aes-ctr-128
AES in counter mode with 128 Bits
aes-ctr-192
AES in counter mode with 192 Bits
aes-ctr-256
AES in counter mode with 256 Bits
-e, --role <role>
SATP uses different session keys for inbound and outbound traffic. The role parameter
is used to determine which keys to use for outbound or inbound packets. On both sides
of a vpn connection different roles have to be used. Possible values are left and
right. You may also use alice or server as a replacement for left and bob or client as
a replacement for right. By default left is used.
-E, --passphrase <passphrase>
This passphrase is used to generate the master key and master salt. For the master key
the last n bits of the SHA256 digest of the passphrase (where n is the length of the
master key in bits) is used. The master salt gets generated with the SHA1 digest. You
may force a specific key and or salt by using --key and --salt.
-K, --key <master key>
master key to use for key derivation
Master key in hexadecimal notation, e.g. 01a2b3c4d5e6f708a9b0cadbecfd0fa1, with a
mandatory length of 32, 48 or 64 characters (128, 192 or 256 bits).
-A, --salt <master salt>
master salt to use for key derivation
Master salt in hexadecimal notation, e.g. 01a2b3c4d5e6f708a9b0cadbecfd, with a
mandatory length of 28 characters (14 bytes).
-c, --cipher <cipher type>
payload encryption algorithm
Encryption algorithm used for encrypting the payload
Possible values:
null
no encryption
aes-ctr
AES in counter mode with 128 Bits, default value
aes-ctr-128
AES in counter mode with 128 Bits
aes-ctr-192
AES in counter mode with 192 Bits
aes-ctr-256
AES in counter mode with 256 Bits
-a, --auth-algo <algo type>
message authentication algorithm
This option sets the message authentication algorithm.
If HMAC-SHA1 is used, the packet length is increased. The additional bytes contain the
authentication data. see --auth-tag-length for more info.
Possible values:
null
no message authentication
sha1
HMAC-SHA1, default value
-b, --auth-tag-length <length>
The number of bytes to use for the auth tag. This value defaults to 10 bytes unless
the null auth algo is used in which case it defaults to 0.
EXAMPLES
P2P Setup between two unicast enpoints:
Host A:
anytun -r hostb.example.com -t tun -n 192.168.123.1/30 -c aes-ctr-256 -k aes-ctr-256 \
-E have_a_very_safe_and_productive_day -e left
Host B:
anytun -r hosta.example.com -t tun -n 192.168.123.2/30 -c aes-ctr-256 -k aes-ctr-256 \
-E have_a_very_safe_and_productive_day -e right
One unicast and one anycast tunnel endpoint:
Unicast tunnel endpoint:
anytun -r anycast.anytun.org -d anytun0 -t tun -n 192.0.2.2/30 -a null -c null -w 0 -e
client
Anycast tunnel endpoints:
On the host with unicast hostname unicast1.anycast.anytun.org and anycast hostname
anycast.anytun.org:
# anytun -i anycast.anytun.org -d anytun0 -t tun -n 192.0.2.1/30 -a null -c null -w 0 -e server \
-S 2342 -M unicast2.anycast.anytun.org:2342,unicast3.anycast.anytun.org:2342
On the host with unicast hostname unicast2.anycast.anytun.org and anycast hostname
anycast.anytun.org:
# anytun -i anycast.anytun.org -d anytun0 -t tun -n 192.0.2.1/30 -a null -c null -w 0 -e server \
-S 2342 -M unicast1.anycast.anytun.org:2342,unicast3.anycast.anytun.org:2342
On the host with unicast hostname unicast3.anycast.anytun.org and anycast hostname
anycast.anytun.org:
# anytun -i anycast.anytun.org -d anytun0 -t tun -n 192.0.2.1/30 -a null -c null -w 0 -e server \
-S 2342 -M unicast1.anycast.anytun.org:2342,unicast2.anycast.anytun.org:2342
For more sophisticated examples (like multiple unicast endpoints to one anycast tunnel
endpoint) please consult the man page of anytun-config(8).
BUGS
Most likely there are some bugs in Anytun. If you find a bug, please let the developers
know at satp@anytun.org. Of course, patches are preferred.
SEE ALSO
anytun-config(8), anytun-controld(8), anytun-showtables(8)
AUTHORS
Othmar Gsenger <otti@anytun.org> Erwin Nindl <nine@anytun.org> Christian Pointner
<equinox@anytun.org>
RESOURCES
Main web site: http://www.anytun.org/
COPYING
Copyright (C) 2007-2014 Markus Grüneis, Othmar Gsenger, Erwin Nindl and Christian
Pointner. This program is free software: you can redistribute it and/or modify it under
the terms of the GNU General Public License as published by the Free Software Foundation,
either version 3 of the License, or any later version.
01/06/2020 ANYTUN(8)