Provided by: ap51-flash_2019.0.1-3_amd64 bug

NAME

       ap51-flash - firmware flasher for ethernet connected routers and access points

SYNOPSIS

       ap51-flash [ -vh ] [ -m mac ] [ interface image ...  ]

DESCRIPTION

       ap51-flash  listens  on  traffic of a network interface, detects remote devices and checks
       the traffic for known identification markers. These markers are send out automatically  by
       supported devices during the initial boot process of the embedded boot loader.

       On  success,  it will search the list of provided images for a matching firmware. A device
       specific communication procedure is initiated to begin the flashing process. The  firmware
       data  is extracted from the selected image and transferred to the device in TFTP server or
       client mode.

       ap51-flash will run in foreground and continue using the interface until it is interrupted
       by  an  SIGINT  signal  (typically  generated by control-C) or SIGTERM signal (for example
       generated by the kill(1) command).

       The interface doesn't require a valid layer 3 network configuration but has to be  set  in
       the  UP  state  (using  the  ip-link(8) command). ap51-flash requires enough privileges to
       capture and inject raw ethernet packets on the selected interface. These  are  often  only
       accessible to the root user.

       While  ap51-flash  doesn't  require a target device specific network configuration or TFTP
       client/server on the same machine, it is recommended to disable any other TFTP  client  or
       server  on  the  system  running  ap51-flash  to  avoid  interferences by a different TFTP
       program.

OPTIONS

       Listed below are the command line options for ap51-flash:

       -m mac, --mac mac
              Adds mac address to the whitelist filter. Only these addresses will be tried to  be
              flashed  when  one  or  more  addresses are supplied. The option has to be supplied
              multiple times to add multiple addresses to the whitelist filter. If not specified,
              all detected devices will be flashed.

       -v, --version
              print ap51-flash version and exit

       -h, --help
              print ap51-flash help and exit

NOTES

       The currently supported devices are

       • Alfa Network AP121F

       • Dlink DIR-300

       • Engenius EOC-1650

       • Engenius EOC-2610

       • Engenius EOC-2610p

       • Engenius 3660

       • FON La Fonera (2100)

       • Open Mesh A40

       • Open Mesh A42

       • Open Mesh A60

       • Open Mesh A62

       • Open Mesh D200

       • Open Mesh G200

       • Open Mesh MR500

       • Open Mesh MR600 (v1, v2)

       • Open Mesh MR900 (v1, v2)

       • Open Mesh MR1750 (v1, v2)

       • Open Mesh OM1P

       • Open Mesh OM2P (v1, v2, v4)

       • Open Mesh OM2P-HS (v1, v2, v3, v4)

       • Open Mesh OM2P-LC

       • Open Mesh OM5P

       • Open Mesh OM5P-AN

       • Open Mesh OM5P-AC (v1, v2)

       • Plasma Cloud PA300

       • Plasma Cloud PA1200

       • Plasma Cloud PA2200

       • Ubiquiti Bullet2 & HP

       • Ubiquiti NanoStation2

       • Ubiquiti NanoStation5

       • Ubiquiti Pico2 & HP

       • Ubiquiti RouterStation

       • UniAppliance Colibrì (!UniData)

       • Zyxel NBG6817

AUTHOR

       ap51-flash  was  written by Marek Lindner and others. This manual page was written by Sven
       Eckelmann <sven@narfation.org>. It is licensed under the terms of the GNU GPL  (version  3
       or later).

                                         August 29, 2019                            AP51-FLASH(8)