NAME

       boltd - thunderbolt device managing system daemon

SYNOPSIS

       boltd [OPTIONS]

DESCRIPTION

       boltd is the thunderbolt device manager daemon. Its goal is to enable the secure and convenient use of
       thunderbolt devices by using the security features of modern thunderbolt controllers. It provides the
       org.freedesktop.bolt name on the system bus. boltd is autostarted via systemd/udev if a thunderbolt
       device is connected.

       The thunderbolt I/O technology works by bridging PCIe between the controllers on each end of the
       connection, which in turn means that devices connected via Thunderbolt are ultimately connected via PCIe.
       Therefore thunderbolt can achieve very high connection speeds, fast enough to even drive external
       graphics cards. The downside is that it also makes certain attacks possible. To mitigate these security
       problems, the latest version — known as Thunderbolt 3 — supports different security levels:

       none
           No security. The behavior is identical to previous Thunderbolt versions.

       dponly
           No PCIe tunnels are created at all, but DisplayPort tunnels are allowed and will work.

       user
           Connected devices must be authorized by the user. Only then will the PCIe tunnels be activated.

       secure
           Basically the same as user mode, but additionally a key will be written to the device the first time
           the device is connected. This key will then be used to verify the identity of the connected device.

       usbonly
           One PCIe tunnel is created to a usb controller in a thunderbolt dock; no other downstream PCIe
           tunnels are authorized (needs 4.17 kernel and recent hardware).

       The primary task of boltd is to authorize thunderbolt peripherals if the security level is either user or
       secure. It provides a D-Bus API to list devices, enroll them (authorize and store them in the local
       database) and forget them again (remove previously enrolled devices). It also emits signals if new
       devices are connected (or removed). During enrollment devices can be set to be automatically authorized
       as soon as they are connected. A command line tool, called boltctl(1), can be used to control the daemon
       and perform all the above mentioned tasks.

       The pre-boot access control list (BootACL) feature is active when supported by the firmware and when
       boltd is running on a new enough Linux kernel (>= 4.17). The BootACL is a list of UUIDs, that can be
       written to the thunderbolt controller. If enabled in the BIOS, all devices in that list will be
       authorized by the firmware during pre-boot, which means these devices can be used in the BIOS setup and
       also during Linux early boot. NB: no device verification is done, even when the security level is set to
       secure mode in the BIOS, i.e. the maximal effective security level for devices in the BootACL is only
       user. If BootACL support is present, all new devices will be automatically added. Devices that are
       forgotten (removed from boltd) will also be removed from the BootACL. When a controller is offline,
       changes to the BootACL will be written to a journal and synchronized back when the controller is online
       again.

       IOMMU support: if the hardware and firmware support using the input–output memory management unit (IOMMU)
       to restrict direct memory access to certain safe regions, boltd will detect that feature and change its
       behavior: As long as iommu support is active, as indicated by the iommu_dma_protection sysfs attribute of
       the domain controller, new devices will be automatically enrolled with the iommu policy and existing
       devices with iommu (or auto) policy will be automatically authorized by boltd without any user
       interaction. When iommu is not active, devices that were enrolled with the iommu policy will not be
       authorized automatically. The status of iommu support can be inspected by using boltctl domains.

OPTIONS

       -h, --help
           Prints a short help text and exits.

       --version
           Shows the version number and exits.

       -r, --replace
           Replace the currently running boltd instance.

       --journal
           Force logging to the journal.

       -v, --verbose
           Print debug output.

ENVIRONMENT

       RUNTIME_DIRECTORY
           Specifies the path where the daemon stores data that only has to live as long as the current boot.
           Will be set automatically when started via systemd (>= 240). If not set the default path for runtime
           data is /run/boltd.

       STATE_DIRECTORY
           Specifies the path where the daemon stores device information, including the keys used for
           authorization. Overwrites the path that was set at compile time. Will be set automatically when
           started via systemd (>= 240).

       BOLT_DBPATH
           Same as STATE_DIRECTORY but takes precedence over that, if set.

EXIT STATUS

       On success 0 is returned, a non-zero failure code otherwise.

AUTHOR

       Written by Christian Kellner <ckellner@redhat.com>.

SEE ALSO

       boltctl(1)

bolt 0.9.2                                         02/07/2022                                           BOLTD(8)