Provided by: sg3-utils_1.46-1ubuntu0.22.04.1_amd64 
NAME
sg3_utils - a package of utilities for sending SCSI commands
SYNOPSIS
sg_* [--dry-run] [--enumerate] [--help] [--hex] [--in=FN] [--inhex=FN] [--maxlen=LEN]
[--raw] [--timeout=SECS] [--verbose] [--version] [OTHER_OPTIONS] DEVICE
DESCRIPTION
sg3_utils is a package of utilities that send SCSI commands to the given DEVICE via a SCSI
pass through interface provided by the host operating system.
The names of all utilities start with "sg" and most start with "sg_" often followed by the
name, or a shortening of the name, of the SCSI command that they send. For example the
"sg_verify" utility sends the SCSI VERIFY command. A mapping between SCSI commands and the
sg3_utils utilities that issue them is shown in the COVERAGE file. The sg_raw utility can
be used to send an arbitrary SCSI command (supplied on the command line) to the given
DEVICE.
sg_decode_sense can be used to decode SCSI sense data given on the command line or in a
file. sg_raw -vvv will output the T10 name of a given SCSI CDB which is most often 16
bytes or less in length.
SCSI draft standards can be found at http://www.t10.org . The standards themselves can be
purchased from ANSI and other standards organizations. A good overview of various SCSI
standards can be seen in http://www.t10.org/scsi-3.htm with the SCSI command sets in the
upper part of the diagram. The highest level (i.e. most abstract) document is the SCSI
Architecture Model (SAM) with SAM-5 being the most recent standard (ANSI INCITS 515-2016)
with the most recent draft being SAM-6 revision 4 . SCSI commands in common with all
device types can be found in SCSI Primary Commands (SPC) of which SPC-4 is the most recent
standard (ANSI INCITS 513-2015). The most recent SPC draft is SPC-5 revision 21. Block
device specific commands (e.g. as used by disks) are in SBC, those for tape drives in SSC,
those for SCSI enclosures in SES and those for CD/DVD/BD drives in MMC.
It is becoming more common to control ATA disks with the SCSI command set. This involves
the translation of SCSI commands to their corresponding ATA equivalents (and that is an
imperfect mapping in some cases). The relevant standard is called SCSI to ATA Translation
(SAT, SAT-2 and SAT-3) are now standards at INCITS(ANSI) and ISO while SAT-4 is at the
draft stage. The logic to perform the command translation is often called a SAT Layer or
SATL and may be within an operating system, in host bus adapter firmware or in an external
device (e.g. associated with a SAS expander). See http://www.t10.org for more information.
There is some support for SCSI tape devices but not for their basic operation. The reader
is referred to the "mt" utility.
There are two generations of command line option usage. The newer utilities (written since
July 2004) use the getopt_long() function to parse command line options. With that
function, each option has two representations: a short form (e.g. '-v') and a longer form
(e.g. '--verbose'). If an argument is required then it follows a space (optionally) in the
short form and a "=" in the longer form (e.g. in the sg_verify utility '-l 2a6h' and
'--lba=2a6h' are equivalent). Note that with getopt_long(), short form options can be
elided, for example: '-all' is equivalent to '-a -l -l'. The DEVICE argument may appear
after, between or prior to any options.
The older utilities, including as sg_inq, sg_logs, sg_modes, sg_opcode, sg_rbuff,
sg_readcap, sg_senddiag, sg_start and sg_turs had individual command line processing code
typically based on a single "-" followed by one or more characters. If an argument is
needed then it follows a "=" ( e.g. '-p=1f' in sg_modes with its older interface). Various
options can be elided as long as it is not ambiguous (e.g. '-vv' to increase the
verbosity).
Over time the command line interface of these older utilities became messy and overloaded
with options. So in sg3_utils version 1.23 the command line interface of these older
utilities was altered to have both a cleaner getopt_long() interface and their older
interface for backward compatibility. By default these older utilities use their
getopt_long() based interface. The getopt_long() is a GNU extension (i.e. not yet POSIX
certified) but more recent command line utilities tend to use it. That can be overridden
by defining the SG3_UTILS_OLD_OPTS environment variable or using '-O' or '--old' as the
first command line option. The man pages of the older utilities documents the details.
Several sg3_utils utilities are based on the Unix dd command (e.g. sg_dd) and permit
copying data at the level of SCSI READ and WRITE commands. sg_dd is tightly bound to Linux
and hence is not ported to other OSes. A more generic utility (than sg_dd) called ddpt in
a package of the same name has been ported to other OSes.
ENVIRONMENT VARIABLES
The SG3_UTILS_OLD_OPTS environment variable is explained in the previous section. It is
only for backward compatibility of the command line options for older utilities.
The SG3_UTILS_DSENSE environment variable may be set to a number. It is only used by the
embedded SNTL within the library used by the utilities in this library. SNTL is a SCSI to
NVMe Translation Layer. This environment variable defaults to 0 which will lead to any
utility that issues a SCSI command that is translated to a NVMe command (by the embedded
SNTL) that fails at the NVMe dvice, to return SCSI sense in 'fixed' format. If this
variable is non-zero then then the returned SCSI sense will be in 'descriptor' format.
Several utilities have their own environment variable setting (e.g. sg_persist has
SG_PERSIST_IN_RDONLY). See individual utility man pages for more information.
There is a Linux specific environment variable called SG3_UTILS_LINUX_NANO that if defined
and the sg driver in the system is 4.0.30 or later, will show command durations in
nanoseconds rather than the default milliseconds. Command durations are typically only
shown if --verbose is used 3 or more times. Due to an interface problem (a 32 bit integer
that should be 64 bits with the benefit of hindsight) the maximum duration that can be
represented in nanoseconds is about 4.2 seconds. If longer durations may occur then don't
define this environment variable (or undefine it).
LINUX DEVICE NAMING
Most disk block devices have names like /dev/sda, /dev/sdb, /dev/sdc, etc. SCSI disks in
Linux have always had names like that but in recent Linux kernels it has become more
common for many other disks (including SATA disks and USB storage devices) to be named
like that. Partitions within a disk are specified by a number appended to the device name,
starting at 1 (e.g. /dev/sda1 ).
Tape drives are named /dev/st<num> or /dev/nst<num> where <num> starts at zero.
Additionally one letter from this list: "lma" may be appended to the name. CD, DVD and BD
readers (and writers) are named /dev/sr<num> where <num> start at zero. There are less
used SCSI device type names, the dmesg and the lsscsi commands may help to find if any are
attached to a running system.
There is also a SCSI device driver which offers alternate generic access to SCSI devices.
It uses names of the form /dev/sg<num> where <num> starts at zero. The "lsscsi -g" command
may be useful in finding these and which generic name corresponds to a device type name
(e.g. /dev/sg2 may correspond to /dev/sda). In the lk 2.6 series a block SCSI generic
driver was introduced and its names are of the form /dev/bsg/<h:c:t:l> where h, c, t and l
are numbers. Again see the lsscsi command to find the correspondence between that SCSI
tuple (i.e. <h:c:t:l>) and alternate device names.
Prior to the Linux kernel 2.6 series these utilities could only use generic device names
(e.g. /dev/sg1 ). In almost all cases in the Linux kernel 2.6 series, any device name can
be used by these utilities.
Very little has changed in Linux device naming in the Linux kernel 3 and 4 series.
WINDOWS DEVICE NAMING
Storage and related devices can have several device names in Windows. Probably the most
common in the volume name (e.g. "D:"). There are also a "class" device names such as
"PhysicalDrive<n>", "CDROM<n>" and "TAPE<n>". <n> is an integer starting at 0 allocated in
ascending order as devices are discovered (and sometimes rediscovered).
Some storage devices have a SCSI lower level device name which starts with a SCSI (pseudo)
adapter name of the form "SCSI<n>:". To this is added sub-addressing in the form of a
"bus" number, a "target" identifier and a LUN (Logical Unit Number). The "bus" number is
also known as a "PathId". These are assembled to form a device name of the form:
"SCSI<n>:<bus>,<target>,<lun>". The trailing ",<lun>" may be omitted in which case a LUN
of zero is assumed. This lower level device name cannot often be used directly since
Windows blocks attempts to use it if a class driver has "claimed" the device. There are
SCSI device types (e.g. Automation/Drive interface type) for which there is no class
driver. At least two transports ("bus types" in Windows jargon): USB and IEEE 1394 do not
have a "scsi" device names of this form.
In keeping with DOS file system conventions, the various device names can be given in
upper, lower or mixed case. Since "PhysicalDrive<n>" is tedious to write, a shortened form
of "PD<n>" is permitted by all utilities in this package.
A single device (e.g. a disk) can have many device names. For example: "PD0" can also be
"C:", "D:" and "SCSI0:0,1,0". The two volume names reflect that the disk has two
partitions on it. Disk partitions that are not recognized by Windows are not usually given
a volume name. However Vista does show a volume name for a disk which has no partitions
recognized by it and when selected invites the user to format it (which may be rather
unfriendly to other OSes).
These utilities assume a given device name is in the Win32 device namespace. To make that
explicit "\\.\" can be prepended to the device names mentioned in this section. Beware
that backslash is an escape character in Unix like shells and the C programming language.
In a shell like Msys (from MinGW) each backslash may need to be typed twice.
The sg_scan utility within this package lists out Windows device names in a form that is
suitable for other utilities in this package to use.
FREEBSD DEVICE NAMING
SCSI disks have block names of the form /dev/da<num> where <num> is an integer starting at
zero. The "da" is replaced by "sa" for SCSI tape drives and "cd" for SCSI CD/DVD/BD
drives. Each SCSI device has a corresponding pass-through device name of the form
/dev/pass<num> where <num> is an integer starting at zero. The "camcontrol devlist"
command may be useful for finding out which SCSI device names are available and the
correspondence between class and pass-through names.
FreeBSD allows device names to be given without the leading "/dev/" (e.g. da0 instead of
/dev/da0). That worked in this package up until version 1.43 when the unadorned device
name (e.g. "da0") gave an error. The original action (i.e. allowing unadorned device
names) has been restored in version 1.46 . Also note that symlinks (to device names) are
followed before prepending "/dev/" if the resultant name doesn't start with a "/".
SOLARIS DEVICE NAMING
SCSI device names below the /dev directory have a form like: c5t4d3s2 where the number
following "c" is the controller (HBA) number, the number following "t" is the target
number (from the SCSI parallel interface days) and the number following "d" is the LUN.
Following the "s" is the slice number which is related to a partition and by convention
"s2" is the whole disk.
OpenSolaris also has a c5t4d3p2 form where the number following the "p" is the partition
number apart from "p0" which is the whole disk. So a whole disk may be referred to as
either c5t4d3, c5t4d3s2 or c5t4d3p0 .
And these device names are duplicated in the /dev/dsk and /dev/rdsk directories. The
former is the block device name and the latter is for "raw" (or char device) access which
is what sg3_utils needs. So in OpenSolaris something of the form 'sg_inq
/dev/rdsk/c5t4d3p0' should work. If it doesn't work then add a '-vvv' option for more
debug information. Trying this form 'sg_inq /dev/dsk/c5t4d3p0' (note "rdsk" changed to
"dsk") will result in an "inappropriate ioctl for device" error.
The device names within the /dev directory are typically symbolic links to much longer
topological names in the /device directory. In Solaris cd/dvd/bd drives seem to be treated
as disks and so are found in the /dev/rdsk directory. Tape drives appear in the /dev/rmt
directory.
There is also a sgen (SCSI generic) driver which by default does not attach to any device.
See the /kernel/drv/sgen.conf file to control what is attached. Any attached device will
have a device name of the form /dev/scsi/c5t4d3 .
Listing available SCSI devices in Solaris seems to be a challenge. "Use the 'format'
command" advice works but seems a very dangerous way to list devices. [It does prompt
again before doing any damage.] 'devfsadm -Cv' cleans out the clutter in the /dev/rdsk
directory, only leaving what is "live". The "cfgadm -v" command looks promising.
NVME SUPPORT
NVMe (or NVM Express) is a relatively new storage transport and command set. The level of
abstraction of the NVMe command set is somewhat lower the SCSI command sets, closer to the
level of abstraction of ATA (and SATA) command sets. NVMe claims to be designed with flash
and modern "solid state" storage in mind, something unheard of when SCSI was originally
developed in the 1980s.
The SCSI command sets' advantage is the length of time they have been in place and the
existing tools (like these) to support it. Plus SCSI command sets level of abstraction is
both and advantage and disadvantage. Recently the NVME-MI (Management Interface) designers
decide to use the SCSI Enclosure Services (SES-3) standard "as is" with the addition of
two tunnelling NVME-MI commands: SES Send and SES Receive. This means after the OS
interface differences are taken into account, the sg_ses, sg_ses_microcode and sg_senddiag
utilities can be used on a NVMe device that supports a newer version of NVME-MI.
The NVME-MI SES Send and SES Receive commands correspond to the SCSI SEND DIAGNOSTIC and
RECEIVE DIAGNOSTIC RESULTS commands respectively. There are however a few other commands
that need to be translated, the most important of which is the SCSI INQUIRY command to the
NVMe Identify controller/namespace. Starting in version 1.43 these utilities contain a
small SNTL (SCSI to NVMe Translation Layer) to take care of these details.
As a side effect of this "juggling" if the sg_inq utility is used (without the --page=
option) on a NVMe DEVICE then the actual NVMe Identifier (controller and possibly
namespace) responses are decoded and output. However if 'sg_inq --page=sinq <device>' is
given for the same DEVICE then parts of the NVMe Identify controller and namespace
response are translated to a SCSI standard INQUIRY response which is then decoded and
output.
Apart from the special case with the sg_inq, all other utilities in the package assume
they are talking to a SCSI device and decode any response accordingly. One easy way for
users to see the underlying device is a NVMe device is the standard INQUIRY response
Vendor Identification field of "NVMe " (an 8 character long string with 4 spaces to the
right).
The following SCSI commands are currently supported by the SNTL library: INQUIRY, MODE
SELECT(10), MODE SENSE(10), READ(10,16), READ CAPACITY(10,16), RECEIVE DIAGNOSTIC RESULTS,
REQUEST SENSE, REPORT LUNS, REPORT SUPPORTED OPERATION CODES, REPORT SUPPORTED TASK
MANAGEMENT FUNCTIONS, SEND DIAGNOSTICS, START STOP UNIT, SYNCHRONIZE CACHE(10,16), TEST
UNIT READY, VERIFY(10,16), WRITE(10,16) and WRITE SAME(10,16).
EXIT STATUS
To aid scripts that call these utilities, the exit status is set to indicate success (0)
or failure (1 or more). Note that some of the lower values correspond to the SCSI sense
key values.
The exit status values listed below can be given to the sg_decode_sense utility (which is
found in this package) as follows:
sg_decode_sense --err=<exit_status>
and a short explanatory string will be output to stdout.
The exit status values are:
0 success. Also used for some utilities that wish to return a boolean value for the
"true" case (and that no error has occurred). The false case is conveyed by exit
status 36.
1 syntax error. Either illegal command line options, options with bad arguments or a
combination of options that is not permitted.
2 the DEVICE reports that it is not ready for the operation requested. The DEVICE
may be in the process of becoming ready (e.g. spinning up but not at speed) so the
utility may work after a wait. In Linux the DEVICE may be temporarily blocked while
error recovery is taking place.
3 the DEVICE reports a medium or hardware error (or a blank check). For example an
attempt to read a corrupted block on a disk will yield this value.
5 the DEVICE reports an "illegal request" with an additional sense code other than
"invalid command operation code". This is often a supported command with a field
set requesting an unsupported capability. For commands that require a "service
action" field this value can indicate that the command with that service action
value is not supported.
6 the DEVICE reports a "unit attention" condition. This usually indicates that
something unrelated to the requested command has occurred (e.g. a device reset)
potentially before the current SCSI command was sent. The requested command has not
been executed by the device. Note that unit attention conditions are usually only
reported once by a device.
7 the DEVICE reports a "data protect" sense key. This implies some mechanism has
blocked writes (or possibly all access to the media).
9 the DEVICE reports an illegal request with an additional sense code of "invalid
command operation code" which means that it doesn't support the requested command.
10 the DEVICE reports a "copy aborted". This implies another command or device problem
has stopped a copy operation. The EXTENDED COPY family of commands (including WRITE
USING TOKEN) may return this sense key.
11 the DEVICE reports an aborted command. In some cases aborted commands can be
retried immediately (e.g. if the transport aborted the command due to congestion).
14 the DEVICE reports a miscompare sense key. VERIFY and COMPARE AND WRITE commands
may report this.
15 the utility is unable to open, close or use the given DEVICE or some other file.
The given file name could be incorrect or there may be permission problems. Adding
the '-v' option may give more information.
17 a SCSI "Illegal request" sense code received with a flag indicating the Info field
is valid. This is often a LBA but its meaning is command specific.
18 the DEVICE reports a medium or hardware error (or a blank check) with a flag
indicating the Info field is valid. This is often a LBA (of the first encountered
error) but its meaning is command specific.
20 the DEVICE reports it has a check condition but "no sense" and non-zero information
in its additional sense codes. Some polling commands (e.g. REQUEST SENSE) can
receive this response. There may be useful information in the sense data such as a
progress indication.
21 the DEVICE reports a "recovered error". The requested command was successful. Most
likely a utility will report a recovered error to stderr and continue, probably
leaving the utility with an exit status of 0 .
22 the DEVICE reports that the current command or its parameters imply a logical block
address (LBA) that is out of range. This happens surprisingly often when trying to
access the last block on a storage device; either a classic "off by one" logic
error or a misreading of the response from READ CAPACITY(10 or 16) in which the
address of the last block rather than the number of blocks on the DEVICE is
returned. Since LBAs are origin zero they range from 0 to n-1 where n is the number
of blocks on the DEVICE, so the LBA of the last block is one less than the total
number of blocks.
24 the DEVICE reports a SCSI status of "reservation conflict". This means access to
the DEVICE with the current command has been blocked because another machine (HBA
or SCSI "initiator") holds a reservation on this DEVICE. On modern SCSI systems
this is related to the use of the PERSISTENT RESERVATION family of commands.
25 the DEVICE reports a SCSI status of "condition met". Currently only the PRE-FETCH
command (see SBC-4) yields this status.
26 the DEVICE reports a SCSI status of "busy". SAM-6 defines this status as the
logical unit is temporarily unable to process a command. It is recommended to
re-issue the command.
27 the DEVICE reports a SCSI status of "task set full".
28 the DEVICE reports a SCSI status of "ACA active". ACA is "auto contingent
allegiance" and is seldom used.
29 the DEVICE reports a SCSI status of "task aborted". SAM-5 says: "This status shall
be returned if a command is aborted by a command or task management function on
another I_T nexus and the Control mode page TAS bit is set to one".
31 error involving two or more command line options. They may be contradicting, select
an unsupported mode, or a required option (given the context) is missing.
32 there is a logic error in the utility. It corresponds to code comments like
"shouldn't/can't get here". Perhaps the author should be informed.
33 the command sent to DEVICE has timed out.
34 this is a Windows only exit status and indicates that the Windows error number (32
bits) cannot meaningfully be mapped to an equivalent Unix error number returned as
the exit status (7 bits).
36 no error has occurred plus the utility wants to convey a boolean value of false.
The corresponding true value is conveyed by a 0 exit status.
40 the command sent to DEVICE has received an "aborted command" sense key with an
additional sense code of 0x10. This value is related to problems with protection
information (PI or DIF). For example this error may occur when reading a block on a
drive that has never been written (or is unmapped) if that drive was formatted with
type 1, 2 or 3 protection.
41 the command sent to DEVICE has received an "aborted command" sense key with an
additional sense code of 0x10 (as with error code) plus a flag indicating the Info
field is valid.
48 this is an internal message indicating a NVMe status field (SF) is other than zero
after a command has been executed (i.e. something went wrong). Work in this area
is currently experimental.
49 low level driver reports a response's residual count (i.e. number of bytes actually
received by HBA is 'requested_bytes - residual_count') that is nonsensical.
50 OS system calls that fail often return a small integer number to help. In Unix
these are called "errno" values where 0 implies no error. These error codes set
aside 51 to 96 for mapping these errno values but that may not be sufficient.
Higher errno values that cannot be mapped are all mapped to this value (i.e. 50).
Note that an errno value of 0 is mapped to error code 0.
50 + <os_error_number>
OS system calls that fail often return a small integer number to help indicate what
the error is. For example in Unix the inability of a system call to allocate memory
returns (in 'errno') ENOMEM which often is associated with the integer 12. So 62
(i.e. '50 + 12') may be returned by a utility in this case. It is also possible
that a utility in this package reports 50+ENOMEM when it can't allocate memory, not
necessarily from an OS system call. In recent versions of Linux the file showing
the mapping between symbolic constants (e.g. ENOMEM) and the corresponding integer
is in the kernel source code file: include/uapi/asm-generic/errno-base.h
Note that errno values that are greater than or equal to 47 cannot fit in range
provided. Instead they are all mapped to 50 as discussed in the previous entry.
97 a SCSI command response failed sanity checks.
98 the DEVICE reports it has a check condition but the error doesn't fit into any of
the above categories.
99 any errors that can't be categorized into values 1 to 98 may yield this value. This
includes transport and operating system errors after the command has been sent to
the device.
100-125
these error codes are used by the ddpt utility which uses the sg3_utils library.
They are mainly specialized error codes associated with offloaded copies.
126 the utility was found but could not be executed. That might occur if the executable
does not have execute permissions.
127 This is the exit status for utility not found. That might occur when a script calls
a utility in this package but the PATH environment variable has not been properly
set up, so the script cannot find the executable.
128 + <signum>
If a signal kills a utility then the exit status is 128 plus the signal number. For
example if a segmentation fault occurs then a utility is typically killed by
SIGSEGV which according to 'man 7 signal' has an associated signal number of 11; so
the exit status will be 139 .
255 the utility tried to yield an exit status of 255 or larger. That should not happen;
given here for completeness.
Most of the error conditions reported above will be repeatable (an example of one that is
not is "unit attention") so the utility can be run again with the '-v' option (or several)
to obtain more information.
COMMON OPTIONS
Arguments to long options are mandatory for short options as well. In the short form an
argument to an option uses zero or more spaces as a separator (i.e. the short form does
not use "=" as a separator).
If an option takes a numeric argument then that argument is assumed to be decimal unless
otherwise indicated (e.g. with a leading "0x", a trailing "h" or as noted in the usage
message).
Some options are used uniformly in most of the utilities in this package. Those options
are listed below. Note that there are some exceptions.
-d, --dry-run
utilities that can cause lots of user data to be lost or overwritten sometimes have
a --dry-run option. Device modifying actions are typically bypassed (or skipped) to
implement a policy of "do no harm". This allows complex command line invocations
to be tested before the action required (e.g. format a disk) is performed. The
--dry-run option has become a common feature of many command line utilities (e.g.
the Unix 'patch' command), not just those from this package.
Note that most hyphenated option names in this package also can be given with an
underscore rather than a hyphen (e.g. --dry_run).
-e, --enumerate
some utilities (e.g. sg_ses and sg_vpd) store a lot of information in internal
tables. This option will output that information in some readable form (e.g. sorted
by an acronym or by page number) then exit. Note that with this option DEVICE is
ignored (as are most other options) and no SCSI IO takes place, so the invoker does
not need any elevated permissions.
-h, -?, --help
output the usage message then exit. In a few older utilities the '-h' option
requests hexadecimal output. In these cases the '-?' option will output the usage
message then exit.
-H, --hex
for SCSI commands that yield a non-trivial response, print out that response in
ASCII hexadecimal. To produce hexadecimal that can be parsed by other utilities
(e.g. without a relative address to the left and without trailing ASCII) use this
option three or four times.
-i, --in=FN
many SCSI commands fetch a significant amount of data (returned in the data-in
buffer) which several of these utilities decode (e.g. sg_vpd and sg_logs). To
separate the two steps of fetching the data from a SCSI device and then decoding
it, this option has been added. The first step (fetching the data) can be done
using the --hex or --raw option and redirecting the command line output to a file
(often done with ">" in Unix based operating systems). The difference between --hex
and --raw is that the former produces output in ASCII hexadecimal while --raw
produces its output in "raw" binary.
The second step (i.e. decoding the SCSI response data now held in a file) can be
done using this --in=FN option where the file name is FN. If "-" is used for FN
then stdin is assumed, again this allows for command line redirection (or piping).
That file (or stdin) is assumed to contain ASCII hexadecimal unless the --raw
option is also given in which case it is assumed to be binary. Notice that the
meaning of the --raw option is "flipped" when used with --in=FN to act on the
input, typically it acts on the output data.
Since the structure of the data returned by SCSI commands varies considerably then
the usage information or the manpage of the utility being used should be checked.
In some cases --hex may need to be used multiple times (and is more conveniently
given as '-HH' or '-HHH).
-i, --inhex=FN
This option has the same or similar functionality as --in=FN. And perhaps 'inhex'
is more descriptive since by default, ASCII hexadecimal is expected in the contents
of file: FN. Alternatively the short form option may be -I or -X. See the "FORMAT
OF FILES CONTAINING ASCII HEX" section below for more information.
-m, --maxlen=LEN
several important SCSI commands (e.g. INQUIRY and MODE SENSE) have response lengths
that vary depending on many factors, only some of which these utilities take into
account. The maximum response length is typically specified in the 'allocation
length' field of the cdb. In the absence of this option, several utilities use a
default allocation length (sometimes recommended in the SCSI draft standards) or a
"double fetch" strategy. See sg_logs(8) for its description of a "double fetch"
strategy. These techniques are imperfect and in the presence of faulty SCSI targets
can cause problems (e.g. some USB mass storage devices freeze if they receive an
INQUIRY allocation length other than 36). Also use of this option disables any
"double fetch" strategy that may have otherwise been used.
-r, --raw
for SCSI commands that yield a non-trivial response, output that response in binary
to stdout. If any error messages or warning are produced they are usually sent to
stderr so as to not interfere with the output from this option.
Some utilities that consume data to send to the DEVICE along with the SCSI command,
use this option. Alternatively the --in=FN option causes DEVICE to be ignored and
the response data (to be decoded) fetched from a file named FN. In these cases this
option may indicate that binary data can be read from stdin or from a nominated
file (e.g. FN).
-t, --timeout=SECS
utilities that issue potentially long-running SCSI commands often have a
--timeout=SECS option. This typically instructs the operating system to abort the
SCSI command in question once the timeout expires. Aborting SCSI commands is
typically a messy business and in the case of format like commands may leave the
device in a "format corrupt" state requiring another long-running re-initialization
command to be sent. The argument, SECS, is usually in seconds and the short form of
the option may be something other than -t since the timeout option was typically
added later as storage devices grew in size and initialization commands took
longer. Since many utilities had relatively long internal command timeouts before
this option was introduced, the actual command timeout given to the operating
systems is the higher of the internal timeout and SECS.
Many long running SCSI commands have an IMMED bit which causes the command to
finish relatively quickly but the initialization process to continue. In such cases
the REQUEST SENSE command can be used to monitor progress with its progress
indication field (see the sg_requests and sg_turs utilities). Utilities that send
such SCSI command either have an --immed option or a --wait option which is the
logical inverse of the "immediate" action.
-v, --verbose
increase the level of verbosity, (i.e. debug output). Can be used multiple times to
further increase verbosity. The additional output caused by this option is almost
always sent to stderr.
-V, --version
print the version string and then exit. Each utility has its own version number and
date of last code change.
NUMERIC ARGUMENTS
Many utilities have command line options that take numeric arguments. These numeric
arguments can be large values (e.g. a logical block address (LBA) on a disk) and can be
inconvenient to enter in the default decimal representation. So various other
representations are permitted.
Multiplicative suffixes are accepted. They are one, two or three letter strings appended
directly after the number to which they apply:
c C *1
w W *2
b B *512
k K KiB *1024
KB kB *1000
m M MiB *1048576
MB mB *1000000
g G GiB *(2^30)
GB gB *(10^9)
t T TiB *(2^40)
TB *(10^12)
p P PiB *(2^50)
PB *(10^15)
An example is "2k" for 2048. The large tera and peta suffixes are only available for
numeric arguments that might require 64 bits to represent internally.
These multiplicative suffixes are compatible with GNU's dd command (since 2002) which
claims compliance with SI and with IEC 60027-2.
A suffix of the form "x<n>" multiplies the preceding number by <n>. An example is "2x33"
for "66". The left argument cannot be '0' as '0x' will be interpreted as hexadecimal
number prefix (see below). The left argument to the multiplication must end in a
hexadecimal digit (i.e. 0 to f) and the whole expression cannot have any embedded
whitespace (e.g. spaces). An ugly example: "0xfx0x2" for 30.
A suffix of the form "+<n>" adds the preceding number to <n>. An example is "3+1k" for
"1027". The left argument to the addition must end in a hexadecimal digit (i.e. 0 to f)
and the whole expression cannot have any embedded whitespace (e.g. spaces). Another
example: "0xf+0x2" for 17.
Alternatively numerical arguments can be given in hexadecimal. There are two syntaxes. The
number can be preceded by either "0x" or "0X" as found in the C programming language. The
second hexadecimal representation is a trailing "h" or "H" as found in (storage)
standards. When hex numbers are given, multipliers cannot be used. For example the decimal
value "256" can be given as "0x100" or "100h".
FORMAT OF FILES CONTAINING ASCII HEX
Such a file is assumed to contain a sequence of one or two digit ASCII hexadecimal values
separated by whitespace. "Whitespace consists of either spaces, tabs, blank lines, or any
combination thereof". Each one or two digit ASCII hex pair is decoded into a byte (i.e. 8
bits). The following will be decoded to valid (ascending valued) bytes: '0', '01', '3',
'c', 'F', '4a', 'cC', 'ff'. Lines containing only whitespace are ignored. The contents of
any line containing a hash mark ('#') is ignored from that point until the end of that
line. Users are encouraged to use hash marks to introduce comments in hex files. The
author uses the extension'.hex' on such files. Examples can be found in the 'inhex'
directory.
MICROCODE AND FIRMWARE
There are two standardized methods for downloading microcode (i.e. device firmware) to a
SCSI device. The more general way is with the SCSI WRITE BUFFER command, see the
sg_write_buffer utility. SCSI enclosures have their own method based on the Download
microcode control/status diagnostic page, see the sg_ses_microcode utility.
SCRIPTS, EXAMPLES and UTILS
There are several bash shell scripts in the 'scripts' subdirectory that invoke compiled
utilities (e.g. sg_readcap). Several of the scripts start with 'scsi_' rather than 'sg_'.
One purpose of these scripts is to call the same utility (e.g. sg_readcap) on multiple
devices. Most of the basic compiled utilities only allow one device as an argument. Some
distributions install these scripts in a more visible directory (e.g. /usr/bin). Some of
these scripts have man page entries. See the README file in the 'scripts' subdirectory.
There is some example C code plus examples of complex invocations in the 'examples'
subdirectory. There is also a README file. The example C may be a simpler example of how
to use a SCSI pass-through in Linux than the main utilities (found in the 'src'
subdirectory). This is due to the fewer abstraction layers (e.g. they don't worry the
MinGW in Windows may open a file in text rather than binary mode).
Some utilities that the author has found useful have been placed in the 'utils'
subdirectory.
WEB SITE
There is a web page discussing this package at http://sg.danny.cz/sg/sg3_utils.html . The
device naming used by this package on various operating systems is discussed at:
http://sg.danny.cz/sg/device_name.html . There is a git code mirror at
https://github.com/hreinecke/sg3_utils . The principle code repository uses subversion and
is on the author's equipment. The author keeps track of this via the subversion revision
number which is an ascending integer (currently at 774 for this package). The github
mirror gets updated periodically from the author's repository. Depending on the time of
update, the above Downloads section at sg.danny.cz may be more up to date than the github
mirror.
AUTHORS
Written by Douglas Gilbert. Some utilities have been contributed, see the CREDITS file and
individual source files (in the 'src' directory).
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 1999-2021 Douglas Gilbert
Some utilities are distributed under a GPL version 2 license while others, usually more
recent ones, are under a FreeBSD license. The files that are common to almost all
utilities and thus contain the most reusable code, namely sg_lib.[hc], sg_cmds_basic.[hc]
and sg_cmds_extra.[hc] are under a FreeBSD license. There is NO warranty; not even for
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sdparm(sdparm), ddpt(ddpt), lsscsi(lsscsi), dmesg(1), mt(1)