Ubuntu Manpage: smp_phy_control - invoke PHY CONTROL SMP function

NAME

       smp_phy_control - invoke PHY CONTROL SMP function

SYNOPSIS

       smp_phy_control  [--attached=ADN]  [--expected=EX]  [--help]  [--hex] [--interface=PARAMS]
       [--max=MA]   [--min=MI]   [--op=OP]   [--phy=ID]   [--pptv=TI]   [--pwrdis=PDC]    [--raw]
       [--sa=SAS_ADDR]  [--sas_pa=CO]  [--sas_sl=CO]  [--sata_pa=CO]  [--sata_sl=CO]  [--verbose]
       [--version] SMP_DEVICE[,N]

DESCRIPTION

       Sends a SAS Serial Management Protocol (SMP)  PHY  CONTROL  function  request  to  an  SMP
       target.  The SMP target is identified by the SMP_DEVICE and the SAS_ADDR. Depending on the
       interface, the SAS_ADDR may be  deduced  from  the  SMP_DEVICE.  The  mpt  interface  uses
       SMP_DEVICE  to  identify  a  HBA  (an  SMP  initiator)  and  needs  the  additional  ,N to
       differentiate between HBAs if there are multiple present.

       The PHY CONTROL function is used to change the state of a phy within an  SMP  target.  SMP
       targets  are  typically  SAS expanders which have multiple phys.  Certain operation values
       (e.g. 'lr' (link reset) and 'hr' (hard reset)) change  the  state  of  the  attached  phy.
       Sending  such  operation  values  to  the  phy  in  the SMP target that is attached to the
       originator (i.e. the SMP initiator) may lead to a bad response.

       Invoking this utility with no arguments (other  than  SMP_DEVICE  which  might  be  in  an
       environment  variable  and  --sa=SAS_ADDR which might be in an environment variable or not
       needed) is harmless. In other words a phy's state is only changed  when  either  --max=MA,
       --min=MI, --op=OP or --pptv=TI is given with a non default value.

OPTIONS

Mandatory arguments to long options are mandatory for short options as well.

-a, --attached=ADN
specifies the attached device name (ADN). The default value is 0 . The ADN is in
decimal but is likely to be a SAS address which is typically shown in hexadecimal.
To specify a number in hexadecimal either prefix it with '0x' or put a trailing 'h'
on it. This option is ignored by the expander unless the '--op=sadn' option is also
given.

-E, --expected=EX
set the 'expected expander change count' field in the SMP request. The value EX is
from 0 to 65535 inclusive with 0 being the default value. When EX is greater than
zero then if the value doesn't match the expander change count of the SMP target
(i.e. the expander) when the request arrives then the target ignores the request
and sets a function result of "invalid expander change count" in the response.

-h, --help
output the usage message then exit.

-H, --hex
output the response (less the CRC field) in hexadecimal.

-I, --interface=PARAMS
interface specific parameters. In this case "interface" refers to the path through
the operating system to the SMP initiator. See the smp_utils man page for more
information.

-M, --max=MA
permits the programmed maximum physical link rate to be changed on the gven phy.
Permitted values are:
0 : no change
8 : 1.5 Gbps
9 : 3 Gbps
10 : 6 Gbps
11 : 12 Gbps
12 : 22.5 Gbps
Default value is 0.

-m, --min=MI
permits the programmed minimum physical link rate to be changed on the given phy.
Permitted values are:
0 : no change
8 : 1.5 Gbps
9 : 3 Gbps
10 : 6 Gbps
11 : 12 Gbps
12 : 22.5 Gbps
Default value is 0.

-o, --op=OP
specifies the operation to be performed on the given phy. The OP argument can be
either numeric or a string. If a number is given, it is put into the 'phy
operation' field of the request. Allowable strings are abbreviations of which only
the first two characters need to match. Each line in the following list contains a
numeric value, a string and then a brief explanation:
0 : nop : no operation
1 : lr : link reset
2 : hr : hard reset
3 : dis : disable phy
5 : cel : clear error log
6 : ca : clear affiliation
7 : tspss: transmit SATA port selection signal
8 : citnl: clear STP I_T nexus loss (bit)
9 : sadn : set attached device name
The default value is 0 (no operation).

-p, --phy=ID
phy identifier. ID is a value between 0 and 254. Default is 0.

-P, --pptv=TI
partial pathway timeout value. The units are microseconds and the permitted values
are between 0 and 15 inclusive. 7 microseconds is recommended by sas2r07.

-D, --pwrdis=PDC
where PDC is the power disable control value. The default value is 0 which means no
change. The value of 1 is reserved; 2, if supported, instructs the management
device server to negate the POWER DISABLE signal; while 3, if supported, instructs
it to assert that signal. This applies to the phy given by ID (which defaults to
0).

-r, --raw
send the response (less the CRC field) to stdout in binary. All error messages are
sent to stderr.

-s, --sa=SAS_ADDR
specifies the SAS address of the SMP target device. Typically this is an expander.
This option may not be needed if the SMP_DEVICE has the target's SAS address within
it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To
give a number in hexadecimal either prefix it with '0x' or put a trailing 'h' on
it.

-q, --sas_pa=CO
set the Enable SAS Partial field to CO which is two bits wide. The defined values
for CO are 0 for no change; 1 for manage partial phy power conditions; 2 for
disable partial phy power conditions.

-l, --sas_sl=CO
set the Enable SAS Slumber field to CO which is two bits wide. The defined values
for CO are 0 for no change; 1 for manage slumber phy power conditions; 2 for
disable slumber phy power conditions.

-Q, --sata_pa=CO
set the Enable SATA Partial field to CO which is two bits wide. The defined values
for CO are 0 for no change; 1 for manage partial phy power conditions; 2 for
disable partial phy power conditions.

-L, --sata_sl=CO
set the Enable SATA Slumber field to CO which is two bits wide. The defined values
for CO are 0 for no change; 1 for manage slumber phy power conditions; 2 for
disable slumber phy power conditions.

-v, --verbose
increase the verbosity of the output. Can be used multiple times

-V, --version
print the version string and then exit.

NOTES

       Once  an expander phy has been disabled with --op=dis then it can be later re-enabled with
       a link reset or hard reset (e.g. --op=lr).

EXAMPLES

       See "Examples" section in http://sg.danny.cz/sg/smp_utils.html

CONFORMING TO

       The SMP PHY CONTROL function was introduced in SAS-1 .

AUTHORS

       Written by Douglas Gilbert.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright © 2006-2015 Douglas Gilbert
       This software is distributed under a FreeBSD license. There is NO warranty; not  even  for
       MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.