Ubuntu Manpage: geod - Geodesic computations

NAME

       geod - Geodesic computations

SYNOPSIS

          geod +ellps=<ellipse> [-afFIlptwW [args]] [+opt[=arg] ...] file ...

          invgeod +ellps=<ellipse> [-afFIlptwW [args]] [+opt[=arg] ...] file ...

DESCRIPTION

geod (direct) and invgeod (inverse) perform geodesic (Great Circle) computations for
determining latitude, longitude and back azimuth of a terminus point given a initial point
latitude, longitude, azimuth and distance (direct) or the forward and back azimuths and
distance between an initial and terminus point latitudes and longitudes (inverse). The
results are accurate to round off for |f| < 1/50, where f is flattening.

invgeod may not be available on all platforms; in this case use geod -I instead.

The following command-line options can appear in any order:

-I Specifies that the inverse geodesic computation is to be performed. May be used
with execution of geod as an alternative to invgeod execution.

-a Latitude and longitudes of the initial and terminal points, forward and back
azimuths and distance are output.

-t<a> Where a specifies a character employed as the first character to denote a control
line to be passed through without processing.

-le Gives a listing of all the ellipsoids that may be selected with the +ellps= option.

-lu Gives a listing of all the units that may be selected with the +units= option.
(Default units are meters.)

-f <format>
Where format is a printf format string to control the output form of the geographic
coordinate values. The default mode is DMS.

-F <format>
Where format is a printf format string to control the output form of the distance
value. The default mode is "%.3f".

-w<n> Where n is the number of significant fractional digits to employ for seconds output
(when the option is not specified, -w3 is assumed).

-W<n> Where n is the number of significant fractional digits to employ for seconds
output. When -W is employed the fields will be constant width with leading zeroes.

-p This option causes the azimuthal values to be output as unsigned DMS numbers
between 0 and 360 degrees. Also note -f.

The +opt command-line options are associated with geodetic parameters for specifying the
ellipsoidal or sphere to use. controls. The options are processed in left to right order
from the command line. Reentry of an option is ignored with the first occurrence assumed
to be the desired value.

See the PROJ documentation for a full list of these parameters and controls.

One or more files (processed in left to right order) specify the source of data to be
transformed. A - will specify the location of processing standard input. If no files are
specified, the input is assumed to be from stdin.

For direct determinations input data must be in latitude, longitude, azimuth and distance
order and output will be latitude, longitude and back azimuth of the terminus point.
Latitude, longitude of the initial and terminus point are input for the inverse mode and
respective forward and back azimuth from the initial and terminus points are output along
with the distance between the points.

Input geographic coordinates (latitude and longitude) and azimuthal data must be in
decimal degrees or DMS format and input distance data must be in units consistent with the
ellipsoid major axis or sphere radius units. The latitude must lie in the range
[-90d,90d]. Output geographic coordinates will be in DMS (if the -f switch is not
employed) to 0.001" with trailing, zero-valued minute-second fields deleted. Output
distance data will be in the same units as the ellipsoid or sphere radius.

The Earth's ellipsoidal figure may be selected in the same manner as program proj by using
+ellps=, +a=, +es=, etc.

geod may also be used to determine intermediate points along either a geodesic line
between two points or along an arc of specified distance from a geographic point. In both
cases an initial point must be specified with +lat_1=lat and +lon_1=lon parameters and
either a terminus point +lat_2=lat and +lon_2=lon or a distance and azimuth from the
initial point with +S=distance and +A=azimuth must be specified.

If points along a geodesic are to be determined then either +n_S=integer specifying the
number of intermediate points and/or +del_S=distance specifying the incremental distance
between points must be specified.

To determine points along an arc equidistant from the initial point both +del_A=angle and
+n_A=integer must be specified which determine the respective angular increments and
number of points to be determined.

EXAMPLES

       The  following script determines the geodesic azimuths and distance in U.S.  statute miles
       from Boston, MA, to Portland, OR:

          geod +ellps=clrk66 <<EOF -I +units=us-mi
          42d15'N 71d07'W 45d31'N 123d41'W
          EOF

       which gives the results:

          -66d31'50.141" 75d39'13.083" 2587.504

       where the first two values are the azimuth from Boston to Portland, the back azimuth  from
       Portland to Boston followed by the distance.

       An  example of forward geodesic use is to use the Boston location and determine Portland's
       location by azimuth and distance:

          geod +ellps=clrk66 <<EOF +units=us-mi
          42d15'N 71d07'W -66d31'50.141" 2587.504
          EOF

       which gives:

          45d31'0.003"N 123d40'59.985"W 75d39'13.094"

       NOTE:
          Lack of precision in the distance value  compromises  the  precision  of  the  Portland
          location.

BUGS

       A  list  of  known bugs can be found at https://github.com/OSGeo/PROJ/issues where new bug
       reports can be submitted to.

HOME PAGE

       https://proj.org/

AUTHOR

       Charles Karney

COPYRIGHT

       1983-2022