Ubuntu Manpage: mdustats - MDU traffic statistics

Provided by: plc-utils-extra_0.0.6+git20211210.358dfcf-2_amd64

NAME

       mdustats - MDU traffic statistics

SYNOPSIS

       mdustats [options] [device] [device] [...]

DESCRIPTION

       Collect  and  display  MDU  traffic  statistics using the Qualcomm Atheros vendor specific
       VS_MDU_TRAFFIC_STATS message.

       This program is part of the Qualcomm Atheros Powerline Toolkit.  See the plc man page  for
       an overview and installation instructions.

OPTIONS

-c command
An integer indicating the type of statistics to be collected and reported.
Permitted values are 0 through 255 decimal but only 4 through 15 are valid at this
time. This option is mandatory because the default value of 0 is invalid.
4 - retrieve traffic statistics on the slave side
5 - retrieve traffic statistics (master TX/RX) collected on the master side
6 - retrieve traffic statistics (slave TX/RX) collected on the master side
7 - retrieve traffic statistics (master/slave TX/RX) collected on the master side
8 - clear traffic statistics on the slave side
9 - clear traffic statistics (master TX/RX) colleted on the master side
10 - clear traffic statistics (slave TX/RX) collected on the master side
11 - clear traffic statistics (master/slave TX/RX) collected on the master side
12 - retrieve then clear traffic statistics collected on the slave side
13 - retrieve then clear traffic statistics (master TX/RX) collected on the master
side
14 - retrieve then clear traffic statistics (slave TX/RX) collected on the master
side
15 - retrieve then clear traffic statistics (master/slave TX/RX) collected on the
master side

-s session
The session identifier used to associate request/confirm message pairs. Valid
identifiers are 0 through 255. The default is 0.

-t milliseconds
Read timeout in milliseconds. Values range from 0 through UINT_MAX. This is the
maximum time allowed for a response. The default is shown in brackets on the
program menu.

-u unit
The slave unit number. This is the same as the slave Terminal Equipment Identifier
or TEI. Valid unit numbers are 0 through 255. Unit 0 is the default. This option
is ignored when option -c specified any of the "slave side" commands 4, 8 or 12.

-v Print additional information on stdout.

-x Cause the program to exit on the first error instead of continuing with remaining
iterations, operations or devices. Normally, the program reports errors and moves
on to the next operation, iteration or device depending on the command line.

-?,--help
Print program help summary on stdout. This option takes precedence over other
options on the command line.

-?,--version
Print program version information on stdout. This option takes precedence over
other options on the command line. Use this option when sending screen dumps to
Atheros Technical Support so that they know exactly which version of the Linux
Toolkit you are using.

ARGUMENTS

       device The  Ethernet hardware address of some powerline device.  More than one address may
              be specified on the command line.  If more  than  one  address  is  specified  then
              operations are performed on each device in turn.  The default address is local.  as
              explained in the DEVICES section.

DEVICES

       Powerline devices use Ethernet hardware, or Media Access Control (MAC), addresses.  Device
       addresses  are expressed as 12 hexadecimal digits (0123456789ABCDEFabcdef) in upper, lower
       or mixed case.  Individual octets may be separated by colons, for  clarity,  but  not  all
       octets  need  to  be  seperated.   For  example,  "00b052000001",  "00:b0:52:00:00:01" and
       "00b052:000001" are valid and equivalent.

       These symbolic addresses are recognized by this program and may be  used  instead  of  the
       actual address value.

       all    Equivalent to "broadcast", described next.

       broadcast
              A  synonym  for  the  standard  Ethernet broadcast address, FF:FF:FF:FF:FF:FF.  All
              devices, whether local, remote or foreign will respond to this address.

       local  A synonym for the Qualcomm Atheros vendor specific Local Management Address  (LMA),
              00:B0:52:00:00:01.   All  local  Atheros  devices  will  recognize this address but
              remote and foreign devices will not.  A remote device is any device at the far  end
              of  a  powerline  connection.   A  foreign device is any device not manufactured by
              Atheros.

REFERENCES

       See  the  Qualcomm  Atheros  Powerline  Firmware  Technical  Reference  Manual  for   more
       information about MDU powerline configuration and the VS_MDU_TRAFFIC_STATS message type.

DISCLAIMER

       Atheros   HomePlug  AV  Vendor  Specific  Management  Message  structure  and  content  is
       proprietary to Qualcomm Atheros, Ocala FL USA.  Consequently, public information  may  not
       be  available.  Qualcomm Atheros reserves the right to modify message structure or content
       in future firmware releases without any obligation to notify or compensate users  of  this
       program.

EXAMPLES

       The  following  example  collects and displays MDU traffic statistics on the slave side of
       the local device because option -c is 4.  The local device is implicit because  no  device
       is specified on the command line.

          # mdustats -c 4

       The  next  example  collects and displays MDU traffic statistics for slave 2 on the master
       side of device 00:b0:52:9F:E0:14 because option -c is 5 and option -s is  2.   The  master
       device is explicit in this example.

          # mdustats -c 5 -u 2 00b0529FE014

CREDITS

        Charles Maier