NAME

       nvme-rpmb - Send RPMB commands to an NVMe device

SYNOPSIS

       nvme rpmb <device> [--cmd=<command> | -c <command>]
                           [--msgfile=<data-file> | -f <data-file>]
                           [--keyfile=<key-file> | -g <key-file>]
                           [--key=<key> | -k <key>]
                           [--msg=<data> | -d <data>]
                           [--address=<offset> | -o <offset>]
                           [--blocks=<512 byte sectors> | -b <sectors> ]
                           [--target=<target-id> | -t <id> ]

DESCRIPTION

       For the NVMe device given, send an nvme rpmb command and provide the results.

       The <device> parameter is mandatory and NVMe character device (ex: /dev/nvme0) must be
       specified. If the given device supports RPMB targets, command given with --cmd or -c
       option shall be sent to the controller. If given NVMe device doesn’t support RPMB targets,
       a message indicating the same shall be printed along with controller register values
       related RPMB.

OPTIONS

       -c <command>, --cmd=<command>
           RPMB command to be sent to the device. It can be one of the following

               info          - print information regarding supported RPMB targets and
                               access and total sizes. No further arguments are required

               program-key   - program 'key' specified with -k option or key read from
                               file specified with --keyfile option to the specified
                               RPMB target given with --target or -t options. As per
                               spec, this is one time action which can't be undone.

               read-couter   - Read 'write counter' of specified RPMB target. The
                               counter value read is printed onto STDOUT

               read-config   - Read 512 bytes of device configuration block data of
                               specified RPMB target of the NVMe device. The data read
                               is written to input file specified with --msgfile or -f
                               option.
               write-config  - Write 512 byes of device configuration block data
                               from file specified by --msgfile or -f options to the
                               RPMB target specified with --target or -t options.

               read-data     - Supports authenticated data reading from specified
                               RPMB target (--target or -t option) at given offset
                               specified with --address or -o option, using key
                               specified using --keyfile or -k options. --blocks or
                               -o option should be given to read the amount of data
                               to be read in 512 byte blocks.

               write-data    - Supports authenticated data writting to specified RPMB
                               target (--target or -t option) at given offset
                               specified with --address or -o option, using key
                               specified using --keyfile or -k options. --blocks or
                               -o option should be given to indicate amount of data
                               to be written in 512 byte blocks.

               For data transfer (read/write) commands, if the specified size is not
               within the total size supported by a target, the request is failed
               nvme-rpmb without sending it to device. RPMB target 0 is used as the
               default target if --target or -t is not specified. 0x0 is used as the
               default address if no -address or -o option is specified,

       -t <target>, --target=<target>
           RPMB target id. This should be one of the supported RPMB targets as reported by info
           command. If nothing is given, default of 0 is used as RPMB target.

       -k <key>, --key=<key>, -g <key-file>, --keyfile=<key-file>
           Authentication key to be used for read/write commands. This should have been already
           programmed by program-key command for given target. Key can be specified on command
           line using --key or -k options. Key can also be specified using file argument
           specified with --keyfile or -g options.

       -f <data-file>, --msgfile=<data-file>
           Name of the file to be used for data transfer commands (read or write). For read
           command, if an existing file is specified, it will be appended.

       -d <data>, --msg=<data>
           These options provide the data on the command line itself.

       -o <offset>, --address=<offset>
           The address (in 512 byte sector offset from 0) to be used for data trasnfer commands
           (read or write) for a specified RPMB target.

       -b, --blocks=<sectors>
           The size in 512 byte sectors to be used for data trasnfer commands (read or write) for
           a specified RPMB target.

EXAMPLES

       •   Print RPMB support information of an NVMe device

               # nvme rpmb /dev/nvme0 --cmd=info

       •   Program SecreteKey as authentication key for target 1

               # nvme rpmb /dev/nvme0 --cmd=program-key -key='SecretKey' --target=1

       •   Read current write counter of RPMB target 0

               # nvme rpmb /dev/nvme0 --cmd=read-counter --target=0

       •   Read configuration data block of target 2 into config.bin file

               # nvme rpmb /dev/nvme0 --cmd=read-config --target=2 -f config.bin

       •   Write 200 blocks of (512 bytes) from input.bin onto target 0

               # nvme rpmb /dev/nvme0 -c write-data -t 0 -f input.bin -b 200 -k 'SecreteKey'

       •   Read 200 blocks of (512 bytes) from target 2, at offset 0x100 and save the

       •   data onto output.bin

               # nvme rpmb /dev/nvme0 -c read-data -t 2 -f out.bin -b 200 -o 0x100

NVME

       Part of the nvme-user suite