Provided by: netpbm_10.97.00-2_amd64 
NAME
pbmtoppa - convert PBM image to HP Printer Performance Architecture (PPA)
SYNOPSIS
pbmtoppa [pbm_file [ppa_file]]
DESCRIPTION
This program is part of Netpbm(1).
pbmtoppa converts page images in PBM format to Hewlett Packard's PPA (Printer Performance
Architecture) format, which is the data stream format expected by some HP "Windows-only"
printers including the HP Deskjet 820C series, the HP DeskJet 720 series, and the HP
DeskJet 1000 series.
pbm_file is the file specification of the input file or - for Standard Input. The default
is Standard Input.
The input file contains one or more PBM images, with each one being a single page. Each
image must have the exact dimensions of a page (at 600 pixels per inch in both
directions). Significantly, this is the format that Ghostscript produces.
ppa_file is the file specification of the output file or - for Standard Output. The
default is Standard Output.
To print Postscript on an HP PPA printer, just use Ghostscript with the pbmraw (or pbm)
device driver.
You can generate a test page for use with this program with pbmpage.
You can also set up a printer filter so you can submit PBM input directly to your print
queue. See the documentation for your print spooler for information on how to do that, or
look in hp820install.doc for an example lpd print filter for Postscript and text files.
Sometimes, pbmtoppa generates a file which the printer will not print (because pbmtoppa's
input is unprintable). When this happens, all three lights blink to signal the error.
This is usually because there is material outside of the printer's printable area. To
make the file print, increase the margins via pbmtoppa options or a configuration file.
See the section on calibration ⟨#calibration⟩ below.
About PPA
The PPA printer language is a far lower level language than most. When you use a PPA
printer, most of the processing that a conventional printer does is done instead on the
computer end of the wire. In particular, pbmtoppa has to do "swath cutting," and "sweep
formatting," which other printers do themselves. There is very little intelligence inside
a PPA printer; pbmtoppa generates direct controls for the printer's hardware.
The design goal of PPA was to reduce the cost of a printer by exploiting computing
resources already present in the computer that requests the printing. CPU power, ROM, and
RAM requirements inside the printer are all reduced compared to a conventional printer.
PPA was new in 1997. It was preceded by Hewlett Packard's PCL (Printer Control Language)
language. HP manufactured PPA printers for only a few years, and no one else ever did.
OPTIONS
In addition to the options common to all programs based on libnetpbm (most notably -quiet,
see
Common Options ⟨index.html#commonoptions⟩ ), pbmtoppa recognizes the following command
line options:
-v version
printer version (720, 820, or 1000)
-x xoff
horizontal offset adjustment in 1/600 inches.
-y yoff
vertical offset adjustment in 1/600 inches.
-t topmarg
top margin in 1/600 inches (default: 150 = 0.25 inch)
-l leftmarg
left margin in 1/600 inches (default: 150 = 0.25 inch)
-r rightmarg
right margin in 1/600 inches (default: 150 = 0.25 inch)
-b botmarg
bottom margin in 1/600 inches (default: 150 = 0.25 inch)
-s paper
paper size: us or a4. Default is us.
-d dpi Print resolution in dots per inch.
-f cfgfile
Read parameters from the configuration file named cfgfile. See CONFIGURATION FILES
⟨#configfile⟩
The offset adjustments you specify with -x and -y accumulate. I.e. if you specify them
multiple times, the total offset adjustment is the sum of the adjustments you specify. -x
60 -x 120 is the same as -x 180.
The -v option undoes any preceding -x and -y options, leaving the horizontal and vertical
adjustments their default values.
CONFIGURATION FILES
You can use a configuration file to specify parameters rather than use invocation options.
pbmtoppa processes the file /etc/pbmtoppa.conf, if it exists, before processing any
options. It then processes each configuration file named by a -f option in order,
applying the parameters from the configuration file as if they were invocation options
used in the place of the -f option.
Configuration files have the following format:
#Comment
key1 value1
key2 value2
[etc.]
Valid keys are version, xoffset, yoffset, topmargin, leftmargin, rightmargin,
bottommargin, papersize, or any non-null prefix of these words. Valid values are the same
as with the corresponding invocation parameters.
EXAMPLES
Print a test pattern:
pbmpage | pbmppa >/dev/lp1
Print three pages:
cat page1.pbm page2.pbm page3.pbm | pbmppa >/dev/lp1
Print the Postscript file myfile.ps:
gs -sDEVICE=rawpbm -q -dNOPAUSE -r600 \
-sOutputFile=- myfile.ps ;\
| pbmtoppa | lpr
CALIBRATION
To be able to print successfully and properly, you need to tell pbmtoppa an X and a Y
offset appropriate for your printer to use when generating the page. You can specify
these offsets with the -x and -y invocation options or with the xoff and yoff parameters
in a pbmtoppa configuration file.
To determine the correct offsets, use the pbmpage program.
If while trying to do this calibration, the printer refuses to print a page, but just
blinks all three lights, specify large margins (e.g. 600 pixels -- one inch) via pbmpage
invocation options while doing the calibration.
For example:
pbmpage | pbmtoppa >/dev/lp1
or
pbmpage | pbmtoppa | lpr -l
(if your printer filter recognizes the '-l' (direct output) parameter).
In the test pattern, the grid is marked off in pixel coordinate numbers. Unfortunately,
these coordinates are probably cut off before the edge of the paper. You'll have to use a
ruler to estimate the pixel coordinate of the left and top edges of the actual sheet of
paper (should be within +/- 300, may be negative; there are 600 pixels per inch).
Add these coordinates to the X and Y offsets by either editing the configuration file or
using the -x and -y command-line parameters.
When pbmtoppa is properly calibrated, the center mark should be in the center of the
paper. Also, the margins should be able to be as small as 1/4 inch without causing the
printer to choke with 'blinking lights syndrome'.
RED HAT LINUX INSTALLATION
RedHat users may find the following tip from Panayotis Vryonis <vrypan@hol.gr> helpful.
The same should work for the 820 and 1000, but it hasn't been tested. Also, use the
pbmraw GSDriver if you have it; it's faster.
Here is a tip to integrate HP720C capability in RedHat's printtool:
Install pbmtoppa. Copy pbmtoppa to /usr/bin.
Edit "printerdb" (in my system it is found in /usr/lib/rhs/rhs-printfilters ) and append
the following lines:
----------------------Cut here-----------------------
StartEntry: DeskJet720C
GSDriver: pbm
Description: {HP DeskJet 720C}
About: { \
This driver drives the HP DeskJet 720C \
inkjet printer. \
It cannot do color printing. \
IMPORTANT! Insert \
"- | pbm2ppa -" \
in the "Extra GS Options " field.\
}
Resolution: {600} {600} {}
EndEntry
----------------------------------------------------
Now you can add an HP720C printer just like any other, using printtool.
SEE ALSO
pbmpage(1), pstopnm(1), pbm(1)
This program was derived from pbm2ppa. pbm2ppa is obsolete and has been replaced by
pnm2ppa, which does the same things as pbmtoppa except it also works with color and has
lots more features. See http://pnm2ppa.sourceforge.net ⟨http://pnm2ppa.sourceforge.net⟩
for more information about the PPA protocol and the separately distributed pnm2ppa
program.
The file INSTALL-MORE in the pbmtoppa directory of the Netpbm source code contains
detailed instructions on setting up a system to use pbmtoppa to allow convenient printing
on HP PPA printers. It was written by Michael Buehlmann.
AUTHOR
Tim Norman. Copyright (C) 1998. Licensed under GNU Public License
Manual page by Bryan Henderson, May 2000.
DOCUMENT SOURCE
This manual page was generated by the Netpbm tool 'makeman' from HTML source. The master
documentation is at
http://netpbm.sourceforge.net/doc/pbmtoppa.html