Provided by: ntpsec_1.2.1+dfsg1-7_amd64 bug


       ntp.conf - Network Time Protocol (NTP) daemon configuration file format




       The ntp.conf configuration file is read at initial startup by the ntpd(8) daemon in order
       to specify the synchronization sources, modes, and other related information. Usually, it
       is installed in the /etc directory, but could be installed elsewhere (see the daemon’s -c
       command line option).

       The file format is similar to other UNIX configuration files. Comments begin with a ‘#’
       character and extend to the end of the line; blank lines are ignored. Configuration
       commands consist of an initial keyword followed by a list of arguments, some of which may
       be optional, separated by whitespace. Commands may not be continued over multiple lines.
       Arguments may be host names, host addresses written in numeric, dotted-quad form,
       integers, floating point numbers (when specifying times in seconds) and text strings.

       Configuration files may have inclusion lines. The syntax is includefile followed by
       whitespace followed by a file or directory name. The configuration is evaluated as though
       the text of the file - or all files of the directory with the extension ".conf" - were
       textually spliced in at the point of the include. Relative paths will work, even when the
       -c option changes the config directory root.

       The rest of this page describes the configuration and control options. The "Notes on
       Configuring NTP and Setting up an NTP Subnet" page (available as part of the HTML
       documentation provided under /usr/share/doc/ntp) contains an extended discussion of these
       options. In addition to the discussion of general Configuration Options, there are
       sections describing the following supported functionality and the options used to control

       •   Authentication Support

       •   NTS Support

       •   Monitoring Support

       •   Access Control Support

       •   Automatic NTP Configuration Options

       •   Reference Clock Support

       •   Miscellaneous Options

       Following these is a section describing Miscellaneous Options. While there is a rich set
       of options available, the only required option is one or more pool, server, peer, or
       broadcast commands.


       Following is a description of the configuration commands in NTPv4. There are two classes
       of commands, association commands that configure a persistent association with a remote
       server or peer or reference clock, and auxiliary commands that specify environment
       variables that control various related operations.

   Association Commands
       Only those options applicable to each command are listed below. Use of options not listed
       may not be caught as an error, but may result in some weird and even destructive behavior.

       In contexts where a host name is expected, a -4 or --ipv4 qualifier preceding the host
       name forces DNS resolution to the IPv4 namespace, while a -6 or --ipv6 qualifier forces
       DNS resolution to the IPv6 namespace.

       In these commands, an address can be any of (a) an IPV4 address in a.b.c.d format, (b) an
       IPV6 address in [a:b:c:d:e:f:g:h] format, (c) a link-local IPV6 address with an interface
       specified in [a:b:c:d:e:f:g:h]%device format, or (d) a DNS hostname.

       pool address [burst] [iburst] [version version] [prefer] [minpoll minpoll] [maxpoll
       maxpoll] [preempt]

       server address [key key] [burst] [iburst] [version version] [prefer] [minpoll minpoll]
       [maxpoll maxpoll]

       peer address [key key] [version version] [prefer] [minpoll minpoll] [maxpoll maxpoll]

       unpeer [address | associd | clock clocktype [unit unitnum]]
           These four commands specify the time server name or address to be used and the mode in
           which to operate. The address can be either a DNS name or an IP address in dotted-quad
           notation. If it is a refclock, it can be clock followed by a type-unit pair as in the
           refclock directive; a missing unit clause is interpreted as unit 0.

           For server addresses, this command mobilizes a persistent client mode association with
           a number of remote servers. In this mode the local clock can synchronized to the
           remote server, but the remote server can never be synchronized to the local clock.

           For server addresses, this command mobilizes a persistent client mode association with
           the specified remote server or local radio clock. In this mode the local clock can
           synchronized to the remote server, but the remote server can never be synchronized to
           the local clock.

           NTP peer mode has been removed for security reasons. peer is now just an alias for the
           server keyword. See above.

           This command removes a previously configured association. An address or association ID
           can be used to identify the association. Either an IP address or DNS name can be used.
           This command is most useful when supplied via ntpq runtime configuration commands
           config and config-from-file.

   Association Options
           Add the command argument, a floating-point value in seconds, to the time offset
           (θ) computed for this server; this may be useful if you are a client on a
           network connection such as an ADSL line where there is a predictable asymmetry between
           upstream and downstream flight times. One way you might see this is if you use a fixed
           set of others and one has a stable offset that is an outlier from the others; in that
           case, you might want to use bias to compensate out the offset.

           When the server is reachable, send a burst of eight packets instead of the usual one.
           The packet spacing is normally 2 s; however, the spacing between the first and second
           packets can be changed with the calldelay command to allow additional time for a modem
           or ISDN call to complete; this is designed to improve timekeeping quality with the
           server command.

           When the server is unreachable, send a burst of six packets instead of the usual one.
           The packet spacing is normally 2 s; however, the spacing between the first and second
           packets can be changed with the calldelay command to allow additional time for a modem
           or ISDN call to complete; this is designed to speed the initial synchronization
           acquisition with the server command, and when ntpd(8) is started with the -q option.

       key key
           All packets sent to and received from the server or peer are to include authentication
           fields encrypted using the specified key identifier with values from 1 to 65535,
           inclusive. The default is to include no encryption field.

       minpoll minpoll, maxpoll maxpoll
           These options specify the minimum and maximum poll intervals for NTP messages, as a
           power of 2 in seconds. The maximum poll interval defaults to 10 (1,024 s), but can be
           increased by the maxpoll option to an upper limit of 17 (36.4 h). The minimum poll
           interval defaults to 6 (64 s), but can be decreased by the minpoll option to a lower
           limit of 0 (1 s).

       mode option
           Pass the option to a reference clock driver. This option is valid only with refclock

           Marks the server as unused, except for display purposes. The server is discarded by
           the selection algorithm.

           Marks the server as preferred. All other things being equal, this host will be chosen
           for synchronization among a set of correctly operating hosts. See the "Mitigation
           Rules and the prefer Keyword" page for further information.

           Mark the association to assume truechimer status; that is, always survive the
           selection and clustering algorithms. This option can be used with any association but
           is most useful for reference clocks with large jitter on the serial port and precision
           pulse-per-second (PPS) signals. Caution: this option defeats the algorithms designed
           to cast out falsetickers and can allow these sources to set the system clock. This
           option is valid only with the server command.

       version version
           Specifies the version number to be used for outgoing NTP packets. Versions 1-4 are the
           choices, with version 4 the default.

   Association Auxiliary Commands
       mdnstries number
           If we are participating in mDNS, after we have synched for the first time we attempt
           to register with the mDNS system. If that registration attempt fails, we try again at
           one minute intervals for up to number times. After all, ntpd may be starting before
           mDNS. The default value for mdnstries is 5.

   Authentication Commands
       The following declarations control MAC authentication:

       controlkey key
           Specifies the key identifier to use with the ntpq(1) utility, which uses the standard
           protocol defined in RFC 5905. The key argument is the key identifier for a trusted
           key, where the value can be in the range 1 to 65,535, inclusive.

       keys keyfile
           Specifies the complete path and location of the key file containing the keys and key
           identifiers used by ntpd(8), and ntpq(1) when operating with symmetric-key
           cryptography. This is the same operation as the -k command line option.

       trustedkey key...
           Specifies the key identifiers which are trusted for the purposes of authenticating
           peers with symmetric key cryptography, as well as keys used by the ntpq(1) program.
           Multiple keys on the same line should be separated by spaces. Key ranges can be
           specified as (first ... last). The spaces around the ... are necessary. Multiple
           trustedkey lines are supported and trusted keys can also be specified on the command

       The MAC authentication procedures require that both the local and remote servers share the
       same key and key identifier for this purpose, although different keys can be used with
       different servers. The key arguments are 32-bit unsigned integers with values from 1 to

   NTS Commands
       The following command controls NTS authentication. It overrides normal TLS protocol
       negotiation, which is not usually necessary.

       nts [enable|disable] [mintls version] [maxtls version] [tlsciphersuites name]

       The options are as follows:

       cert file
           Present the certificate in file as our certificate.

       key file
           Read the private key to our certificate from file.

       ca location
           Use the file, or directory, specified by location to validate NTS-KE server
           certificates instead of the system default root certificates. If a directory is
           specified, it must have files named with their hash, as created by openssl rehash.

       cookie location
           Use the file (or directory) specified by location to store the keys used to make and
           decode cookies. The default is /var/lib/ntpsec/nts-keys.

           Enable NTS-KE server. When enabled, cert and key are required.

           Disable NTS-KE server.

       mintls string
           Set the lowest allowable TLS version to negotiate. Will be useful in the wake of a TLS
           compromise. Reasonable values are TLS1.3 if your system supports it. TLS 1.3 was first
           supported in OpenSSL version 1.1.1.

       maxtls string
           Set the highest allowable TLS version to negotiate. By setting mintls and maxtls
           equal, you can force the TLS version for testing. Format is as for mintls.

       tlsciphersuites string
           An OpenSSL ciphersuite list to configure the allowed ciphersuites for TLS 1.3. A
           single NULL cipher disables encryption and use of certificates.

       aead string
           Specify the crypto algorithm to be used on the wire. The choices come from RFC 5297.
           The only options supported are AES_SIV_CMAC_256, AES_SIV_CMAC_384, and
           AES_SIV_CMAC_512. This slot is dual use. It is the server default if the remote client
           doesn’t request a valid choice and it is also the preference passed to the remote
           client if the server command doesn’t specify a preference. The default is

       The following options of the server command configure NTS (as a client).

           Use Network Time Security (NTS) for authentication. Normally, this is all you have to
           do to activate the client side of NTS. + The hostname following the server command is
           used as the address of the NTS key exchange server (NTS-KE) rather than the address of
           a NTP server. The NTS-KE exchange defaults to using the same IP address for the NTP
           server. + Note that the server hostname must match the name on the NTS-KE server’s

           Do not validate the server certificate.

       ca location
           Use the file, or directory, specified by location to validate the NTS-KE server
           certificate, overriding the site default. Do not use any other CA. If a directory is
           specified, it must have files named with their hash, as created by openssl rehash.

       aead string
           Specify the preferred crypto algorithm to be used on the wire. The only options
           supported are AES_SIV_CMAC_256, AES_SIV_CMAC_384, and AES_SIV_CMAC_512. The server may
           ignore the request. See the aead option above. + The same aead algorithms are also
           used to encrypt cookies. The default is AES_SIV_CMAC_256. There is no config file
           option to change it, but you can change it by editing the saved cookie key file,
           probably /var/lib/ntpsec/nts-keys. Adjust the L: slot to be 48 or 64 and adjust the I:
           slots to have the right number of bytes. Then restart the server. (All old cookies
           held by clients will be rejected so their next 8 NTP requests will be ignored. They
           should recover by retrying NTS-KE to get fresh cookies.)


       ntpd(8) includes a comprehensive monitoring facility suitable for continuous, long term
       recording of server and client timekeeping performance. See the statistics command below
       for a listing and example of each type of statistics currently supported. Statistic files
       are managed using file generation sets and scripts in the ./scripts directory of this
       distribution. Using these facilities and UNIX cron(8) jobs, the data can be automatically
       summarized and archived for retrospective analysis.

   Monitoring Commands
       statistics name...
           Enables writing of statistics records. Currently, eight kinds of name statistics are

               Enables recording of clock driver statistics information. Each update received
               from a clock driver appends a line of the following form to the file generation
               set named clockstats:

               49213 525.624 SPECTRACOM(1) 93 226 00:08:29.606

           │                    │       │                         │
           │Item                │ Units │ Description             │
           │                    │       │                         │
           │49213               │ MJD   │ modified Julian day     │
           │                    │       │ number                  │
           │                    │       │                         │
           │525.624             │ s     │ time of day (s) past    │
           │                    │       │ midnight UTC            │
           │                    │       │                         │
           │SPECTRACOM(1)       │       │ receiver identifier     │
           │                    │       │ (Spectracom unit 1)     │
           │                    │       │                         │
           │93 226 00:08:29.606 │       │ timecode (format varies │
           │                    │       │ by refclock)            │

           The first two fields show the date (Modified Julian Day) and time (seconds and
           fraction past UTC midnight). The next normally shows clock type and unit (but if you
           are running in strict Classic compatibility mode it will show the magic clock address
           in dotted-quad notation). The final field is the last timecode received from the clock
           in decoded ASCII format, where meaningful. For some clock drivers, a good deal of
           additional information can be gathered and displayed as well. See information specific
           to each clock for further details.

               Enables recording of loop filter statistics information. Each update of the local
               clock outputs a line of the following form to the file generation set named

               50935 75440.031 0.000006019 13.778190 0.000351733 0.0133806

           │            │        │                          │
           │Item        │ Units  │ Description              │
           │            │        │                          │
           │50935       │ MJD    │ date                     │
           │            │        │                          │
           │75440.031   │ s      │ time past midnight       │
           │            │        │                          │
           │0.000006019 │ s      │ clock offset             │
           │            │        │                          │
           │13.778      │ PPM    │ drift (frequency offset) │
           │            │        │                          │
           │0.000351733 │ s      │ RMS jitter               │
           │            │        │                          │
           │0.013380    │ PPM    │ RMS frequency jitter     │
           │            │        │ (aka wander)             │
           │            │        │                          │
           │6           │ log2 s │ clock discipline loop    │
           │            │        │ time constant            │

           The first two fields show the date (Modified Julian Day) and time (seconds and
           fraction past UTC midnight). The next five fields show time offset (seconds),
           frequency offset (parts per million - PPM), RMS jitter (seconds), Allan deviation
           (PPM) and clock discipline time constant.

               Record significant peer and system events. Each significant event appends one line
               to the protostats file set:

           49213 525.624 963a 8a message

           │          │       │                         │
           │Item      │ Units │ Description             │
           │          │       │                         │
           │49213     │ MJD   │ date                    │
           │          │       │                         │
           │525.624   │ s     │ time past midnight      │
           │          │       │                         │
           │ │ IP    │ source address ( │
           │          │       │ for system)             │
           │          │       │                         │
           │963a      │ code  │ status word             │
           │          │       │                         │
           │8a        │ code  │ event message code      │
           │          │       │                         │
           │message   │ text  │ event message           │

           The event message code and message field are described on the "Event Messages and
           Status Words" page.

               Enables recording of peer statistics information. This includes statistics records
               of all peers of an NTP server and of special signals, where present and
               configured. Each valid update appends a line of the following form to the current
               element of a file generation set named peerstats:

               48773 10847.650 SPECTRACOM(4) 9714 -0.001605376 0.000000000
                   0.001424877 0.000958674

           │              │       │                      │
           │Item          │ Units │ Description          │
           │              │       │                      │
           │48773         │ MJD   │ date                 │
           │              │       │                      │
           │10847.650     │ s     │ time past midnight   │
           │              │       │                      │
           │SPECTRACOM(4) │       │ clock name (unit) or │
           │              │       │ source address       │
           │              │       │                      │
           │9714          │ hex   │ status word          │
           │              │       │                      │
           │-0.001605376  │ s     │ clock offset         │
           │              │       │                      │
           │0.000000000   │ s     │ roundtrip delay      │
           │              │       │                      │
           │0.001424877   │ s     │ dispersion           │
           │              │       │                      │
           │0.000958674   │ s     │ RMS jitter           │

           The first two fields show the date (Modified Julian Day) and time (seconds and
           fraction past UTC midnight). The third field shows the reference clock type and unit
           number (but if you are running in the peer address in dotted-quad notation instead)
           The fourth field is a status word, encoded in hex in the format described in Appendix
           A of the NTP specification RFC 1305. The final four fields show the offset, delay,
           dispersion and RMS jitter, all in seconds.

               Enables recording of raw-timestamp statistics information. This includes
               statistics records of all peers of an NTP server and of special signals, where
               present and configured. Each NTP message received from a peer or clock driver
               appends a line of the following form to the file generation set named rawstats:

               56285 54575.160 3565350574.400229473
                   3565350574.442385200 3565350574.442436000
                   3565350575.154505763 0 4 4 1 8 -21 0.000000 0.000320
                   PPS 0

           │                     │                          │                          │
           │Item                 │ Units                    │ Description              │
           │                     │                          │                          │
           │56285                │ MJD                      │ date                     │
           │                     │                          │                          │
           │54575.160            │ s                        │ time past midnight       │
           │                     │                          │                          │
           │            │ IP                       │ source address           │
           │                     │                          │                          │
           │          │ IP                       │ destination address      │
           │                     │                          │                          │
           │3565350574.400229473 │ NTP s                    │ origin timestamp         │
           │                     │                          │                          │
           │3565350574.442385200 │ NTP s                    │ receive timestamp        │
           │                     │                          │                          │
           │3565350574.442436000 │ NTP s                    │ transmit timestamp       │
           │                     │                          │                          │
           │3565350575.154505763 │ NTP s                    │ destination timestamp    │
           │                     │                          │                          │
           │0                    │ 0: OK, 1: insert         │ leap warning indicator   │
           │                     │ pending, 2: delete       │                          │
           │                     │ pending, 3: not synced   │                          │
           │                     │                          │                          │
           │4                    │ 4 was current in 2012    │ NTP version              │
           │                     │                          │                          │
           │4                    │ 3: client, 4: server, 6: │ mode                     │
           │                     │ ntpq                     │                          │
           │                     │                          │                          │
           │1                    │ 1-15, 16: not synced     │ stratum                  │
           │                     │                          │                          │
           │8                    │ log2 seconds             │ poll                     │
           │                     │                          │                          │
           │-21                  │ log2 seconds             │ precision                │
           │                     │                          │                          │
           │0.000000             │ seconds                  │ total roundtrip delay    │
           │                     │                          │ from the remote server   │
           │                     │                          │ to the primary reference │
           │                     │                          │ clock                    │
           │                     │                          │                          │
           │0.000320             │ seconds                  │ total dispersion from    │
           │                     │                          │ the remote server to the │
           │                     │                          │ primary reference clock  │
           │                     │                          │                          │
           │.PPS.                │ IP or text               │ refid, association ID    │
           │                     │                          │                          │
           │0                    │ integer                  │ lost packets since last  │
           │                     │                          │ response                 │

           The first two fields show the date (Modified Julian Day) and time (seconds and
           fraction past UTC midnight). The next two fields show the remote peer or clock
           identification followed by the local address in dotted-quad notation. The final four
           fields show the originate, receive, transmit and final NTP timestamps in order. The
           timestamp values are as received and before processing by the various data smoothing
           and mitigation algorithms.

               Enables recording of ntpd statistics counters on a periodic basis. Each hour a
               line of the following form is appended to the file generation set named sysstats:

               50928 2132.543 36000 81965 0 9546 56 71793 512 540 10 147 1

           │         │       │                       │
           │Item     │ Units │ Description           │
           │         │       │                       │
           │50928    │ MJD   │ date                  │
           │         │       │                       │
           │2132.543 │ s     │ time past midnight    │
           │         │       │                       │
           │3600     │ s     │ time since reset      │
           │         │       │                       │
           │81965    │ #     │ packets received      │
           │         │       │                       │
           │0        │ #     │ packets for this host │
           │         │       │                       │
           │9546     │ #     │ current versions      │
           │         │       │                       │
           │56       │ #     │ old version           │
           │         │       │                       │
           │512      │ #     │ access denied         │
           │         │       │                       │
           │540      │ #     │ bad length or format  │
           │         │       │                       │
           │10       │ #     │ bad authentication    │
           │         │       │                       │
           │4        │ #     │ declined              │
           │         │       │                       │
           │147      │ #     │ rate exceeded         │
           │         │       │                       │
           │1        │ #     │ kiss-o'-death packets │
           │         │       │ sent                  │

           The first two fields show the date (Modified Julian Day) and time (seconds and
           fraction past UTC midnight). The remaining ten fields show the statistics counter
           values accumulated since the last generated line.

               Enables recording of ntpd resource usage statistics. Each hour a line of the
               following form is appended to the file generation set named usestats:

               57570 83399.541 3600 0.902 1.451 164 0 0 0 2328 64226 1 0 4308

           │          │       │                          │
           │Item      │ Units │ Description              │
           │          │       │                          │
           │57570     │ MJD   │ date                     │
           │          │       │                          │
           │83399.541 │ s     │ time past midnight       │
           │          │       │                          │
           │3600      │ s     │ time since reset         │
           │          │       │                          │
           │0.902     │ s     │ ru_utime: CPU seconds -  │
           │          │       │ user mode                │
           │          │       │                          │
           │1.451     │ s     │ ru_stime: CPU seconds -  │
           │          │       │ system                   │
           │          │       │                          │
           │164       │ #     │ ru_minflt: page faults - │
           │          │       │ reclaim/soft (no I/O)    │
           │          │       │                          │
           │0         │ #     │ ru_majflt: page faults - │
           │          │       │ I/O                      │
           │          │       │                          │
           │0         │ #     │ ru_nswap: process        │
           │          │       │ swapped out              │
           │          │       │                          │
           │0         │ #     │ ru_inblock: file blocks  │
           │          │       │ in                       │
           │          │       │                          │
           │2328      │ #     │ ru_oublock: file blocks  │
           │          │       │ out                      │
           │          │       │                          │
           │64226     │ #     │ ru_nvcsw: context        │
           │          │       │ switches, wait           │
           │          │       │                          │
           │1         │ #     │ ru_nivcsw: context       │
           │          │       │ switches, preempts       │
           │          │       │                          │
           │0         │ #     │ ru_nsignals: signals     │
           │          │       │                          │
           │4308      │ #     │ ru_maxrss: resident set  │
           │          │       │ size, kilobytes          │

           The first two fields show the date (Modified Julian Day) and time (seconds and
           fraction past UTC midnight). The ru_ tags are the names from the rusage struct. See
           man getrusage for details. (The NetBSD and FreeBSD man pages have more details.) The
           maxrss column is the high water mark since the process was started. The remaining
           fields show the values used since the last report.

       statsdir directory_path
           Indicates the full path of a directory where statistics files should be created (see
           below). This keyword allows the (otherwise constant) filegen filename prefix to be
           modified for file generation sets, which is useful for handling statistics logs.

       filegen name [file filename] [type typename] [link | nolink] [enable | disable]
           Configures setting of the generation file set name. Generation file sets provide a
           means for handling files that are continuously growing during the lifetime of a
           server. Server statistics are a typical example for such files. Generation file sets
           provide access to a set of files used to store the actual data. At any time at most
           one element of the set is being written to. The type given specifies when and how data
           will be directed to a new element of the set. This way, information stored in elements
           of a file set that are currently unused are available for administrative operations
           without the risk of disturbing the operation of ntpd. (Most important: they can be
           removed to free space for new data produced.)

           Note that this command can be sent from the ntpq(1) program running at a remote

               This is the type of the statistics records, as shown in the statistics command.

           file filename
               This is the file name for the statistics records. Filenames of set members are
               built from three concatenated elements prefix, filename and suffix:

           │          │                                  │
           │Attribute │ Description                      │
           │          │                                  │
           │prefix    │ This is a constant filename      │
           │          │ path. It is not subject to       │
           │          │ modifications via the filegen    │
           │          │ option. It is defined by the     │
           │          │ server, usually specified as a   │
           │          │ compile-time constant. It may,   │
           │          │ however, be configurable for     │
           │          │ individual file generation sets  │
           │          │ via other commands. For example, │
           │          │ the prefix used with loopstats   │
           │          │ and peerstats generation can be  │
           │          │ configured using the statsdir    │
           │          │ option explained above.          │
           │          │                                  │
           │filename  │ This string is directly          │
           │          │ concatenated to the prefix       │
           │          │ mentioned above (no intervening  │
           │          │ ‘/’). This can be modified using │
           │          │ the file argument to the filegen │
           │          │ statement. No .. elements are    │
           │          │ allowed in this component to     │
           │          │ prevent filenames referring to   │
           │          │ parts outside the filesystem     │
           │          │ hierarchy denoted by prefix.     │
           │          │                                  │
           │suffix    │ This part is reflects individual │
           │          │ elements of a file set. It is    │
           │          │ generated according to the type  │
           │          │ of a file set.                   │

           type typename
               A file generation set is characterized by its type. The following types are
               supported: // The following are tables only because indent lists cannot be //
               nested more than 2 deep.

           │          │                                  │
           │Attribute │ Description                      │
           │          │                                  │
           │none      │ The file set is actually a       │
           │          │ single plain file.               │
           │          │                                  │
           │pid       │ One element of file set is used  │
           │          │ per incarnation of a ntpd        │
           │          │ server. This type does not       │
           │          │ perform any changes to file set  │
           │          │ members during runtime, however  │
           │          │ it provides an easy way of       │
           │          │ separating files belonging to    │
           │          │ different ntpd(8) server         │
           │          │ incarnations. The set member     │
           │          │ filename is built by appending a │
           │          │ ‘.’ to concatenated prefix and   │
           │          │ filename strings, and appending  │
           │          │ the decimal representation of    │
           │          │ the process ID of the ntpd(8)    │
           │          │ server process.                  │
           │          │                                  │
           │day       │ One file generation set element  │
           │          │ is created per day. A day is     │
           │          │ defined as the period between    │
           │          │ 00:00 and 24:00 UTC. The file    │
           │          │ set member suffix consists of a  │
           │          │ ‘.’ and a day specification in   │
           │          │ the form YYYYMMdd. YYYY is a     │
           │          │ 4-digit year number (e.g.,       │
           │          │ 1992). MM is a two digit month   │
           │          │ number. dd is a two digit day    │
           │          │ number. Thus, all information    │
           │          │ written at 10 December 1992      │
           │          │ would end up in a file named     │
           │          │ prefix filename.19921210.        │
           │          │                                  │
           │week      │ Any file set member contains     │
           │          │ data related to a certain week   │
           │          │ of a year. The term week is      │
           │          │ defined by computing day-of-year │
           │          │ modulo 7. Elements of such a     │
           │          │ file generation set are          │
           │          │ distinguished by appending the   │
           │          │ following suffix to the file set │
           │          │ filename base: A dot, a 4-digit  │
           │          │ year number, the letter W, and a │
           │          │ 2-digit week number. For         │
           │          │ example, information from        │
           │          │ January, 10th 1992 would end up  │
           │          │ in a file with suffix 1992W1.    │
           │          │                                  │
           │month     │ One generation file set element  │
           │          │ is generated per month. The file │
           │          │ name suffix consists of a dot, a │
           │          │ 4-digit year number, and a       │
           │          │ 2-digit month.                   │
           │          │                                  │
           │year      │ One generation file element is   │
           │          │ generated per year. The filename │
           │          │ suffix consists of a dot and a 4 │
           │          │ digit year number.               │
           │          │                                  │
           │age$$     │ This type of file generation     │
           │          │ sets changes to a new element of │
           │          │ the file set every 24 hours of   │
           │          │ server operation. The filename   │
           │          │ suffix consists of a dot, the    │
           │          │ letter a, and an 8-digit number. │
           │          │ This number is taken to be the   │
           │          │ number of seconds the server is  │
           │          │ running at the start of the      │
           │          │ corresponding 24-hour period.    │

           link | nolink
               It is convenient to be able to access the current element of a file generation set
               by a fixed name. This feature is enabled by specifying link and disabled using
               nolink. If link is specified, a hard link from the current file set element to a
               file without suffix is created. When there is already a file with this name and
               the number of links of this file is one, it is renamed appending a dot, the letter
               C, and the pid of the ntpd server process. When the number of links is greater
               than one, the file is unlinked. This allows the current file to be accessed by a
               constant name.

           enable | disable
               Enables or disables the recording function. Information is only written to a file
               generation by specifying enable; output is prevented by specifying disable.


       The ntpd(8) daemon implements a general purpose address/mask based restriction list. The
       list contains address/match entries sorted first by increasing address values and then by
       increasing mask values. A match occurs when the bitwise AND of the mask and the packet
       source address is equal to the bitwise AND of the mask and address in the list. The list
       is searched in order with the last match found defining the restriction flags associated
       with the entry. Additional information and examples can be found in the "Notes on
       Configuring NTP and Setting up a NTP Subnet" page (available as part of the HTML

       The restriction facility was implemented in conformance with the access policies for the
       original NSFnet backbone time servers. Later the facility was expanded to deflect
       cryptographic and clogging attacks. While this facility may be useful for keeping unwanted
       or broken or malicious clients from congesting innocent servers, it should not be
       considered an alternative to the NTP authentication facilities. Source address based
       restrictions are easily circumvented by a determined cracker.

       Clients can be denied service because they are explicitly included in the restrict list
       created by the restrict command or implicitly as the result of cryptographic or rate limit
       violations. Cryptographic violations include certificate or identity verification
       failures; rate limit violations generally result from defective NTP implementations that
       send packets at abusive rates. Some violations cause denied service only for the offending
       packet, others cause denied service for a timed period and others cause the denied service
       for an indefinite period. When a client or network is denied access for an indefinite
       period, the only way at present to remove the restrictions is by restarting the server.

   The Kiss-of-Death Packet
       Ordinarily, packets denied service are simply dropped with no further action except
       incrementing statistics counters. Sometimes a more proactive response is needed, such as a
       server message that explicitly requests the client to stop sending and leave a message for
       the system operator. A special packet format has been created for this purpose called the
       "kiss-of-death" (KoD) packet. KoD packets have the leap bits set unsynchronized and
       stratum set to zero and the reference identifier field set to a four-byte ASCII code. If
       the noserve or notrust flag of the matching restrict list entry is set, the code is
       "DENY"; if the limited flag is set and the rate limit is exceeded, the code is "RATE".
       Finally, if a cryptographic violation occurs, the code is "CRYP".

       A client receiving a KoD performs a set of sanity checks to minimize security exposure,
       then updates the stratum and reference identifier peer variables, sets the access denied
       (BOGON4) bit in the peer flash variable and sends a message to the log. As long as the
       BOGON4 bit is set, the client will send no further packets to the server. The only way at
       present to recover from this condition is to restart the protocol at both the client and
       server. This happens automatically at the client when the association times out. It will
       happen at the server only if the server operator cooperates.


       limit [average average] [burst burst] [kod kod]
           Set the parameters of the limited facility which protects the server from client
           abuse. Internally, each MRU <ntpq.html#mrulist> slot contains a score in units of
           packets per second. It is updated each time a packet arrives from that IP Address. The
           score decays exponentially at the burst rate and is bumped by 1.0/burst when a packet

           average average
               Specify the allowed average rate for response packets in packets per second. The
               default is 1.0

           burst burst
               Specify the allowed burst size if the bursts are far enough apart to keep the
               average rate below average. The default is 20.0

           kod kod
               Specify the allowed average rate for KoD packets in packets per second. The
               default is 0.5

       restrict address[/cidr] [mask mask] [flag ...]
           The address argument expressed in dotted-quad (for IPv4) or :-delimited (for IPv6)
           form is the address of a host or network. Alternatively, the address argument can be a
           valid host DNS name. The mask argument expressed in IPv4 or IPv6 numeric address form
           defaults to all mask bits on, meaning that the address is treated as the address of an
           individual host. Instead of an explicit mask, the address/cidr may be specified in
           CIDR notation. A default entry (address, mask is always included and
           is always the first entry in the list. Note that text string default, with no mask
           option, may be used to indicate the default entry. In the current implementation, flag
           always restricts access, i.e., an entry with no flags indicates that free access to
           the server is to be given. The flags are not orthogonal, in that more restrictive
           flags will often make less restrictive ones redundant. The flags can generally be
           classed into two categories, those which restrict time service and those which
           restrict informational queries and attempts to do a run-time reconfiguration of the
           server. One or more of the following flags may be specified:

               Discard received NTP packets with probability 0.1; that is, on average drop one
               packet in ten. This flag is for testing and amusement. The name comes from Bob
               Braden’s flakeway, which once did a similar thing for early Internet testing.

               Deny packets of all kinds, including ntpq(1) queries.

               If this flag is set when an access violation occurs, a kiss-o'-death (KoD) packet
               is sent. KoD packets are rate limited.

               Deny service if the packet spacing violates the lower limits specified in the
               limit command. A history of clients is kept using the monitoring capability of
               ntpd(8). Thus, monitoring is always active as long as there is a restriction entry
               with the limited flag.

               Enable Microsoft Windows MS-SNTP authentication using Active Directory services.
               Note: Potential users should be aware that these services involve a TCP connection
               to another process that could potentially block, denying services to other users.
               Therefore, this flag should be used only for a dedicated server with no clients
               other than MS-SNTP.

               Deny ntpq(1) queries which attempt to modify the state of the server (i.e., run
               time reconfiguration). Queries which return information are permitted.

               Do not accept MRU-list requests. These can be expensive to service and may
               generate a high volume of response traffic.

               Deny packets which would result in mobilizing a new association; this includes
               symmetric active packets when a configured association does not exist. That used
               to happen when the remote client used the peer command in its config file. We
               don’t support that mode. It used to include pool servers, but they now poke a hole
               in any restrictions.

               Deny ntpq(1) queries. Time service is not affected.

               Deny all packets except ntpq(1) and queries.

               Deny service unless the packet is cryptographically authenticated.

               This is a match algorithm modifier, rather than a restriction flag. Its presence
               causes the restriction entry to be matched if the source port in the packet is the
               standard NTP UDP port (123). Both ntpport and non-ntpport may be specified. The
               ntpport is considered more specific and is sorted later in the list.

               Deny packets that do not match the current NTP version.

       Note: A second restrict line with the same address/mask does not replace the first one.
       The flags are merged. Thus:

           restrict bob X
           restrict bob Y

       is the same as

           restrict bob X Y

       Default restriction list entries with the flags ignore, interface, ntpport, for each of
       the local host’s interface addresses are inserted into the table at startup to prevent the
       server from attempting to synchronize to its own time. A default entry is also always
       present. It has noquery to avoid packet length amplification which can be used for DDoS
       with a forged return address and limited to avoid DDoS reflections.

       unrestrict address[/cidr] [mask mask] [flag ...]
           Like a restrict command, but turns off the specified flags rather than turning them on
           (expected to be useful mainly with ntpq :config). An unrestrict with no flags
           specified removes any rule with matching address and mask. Use only on an address/mask
           or CIDR-format address mentioned in a previous restrict statement.

       Note: unrestrict default will not do anything; you can’t remove the builtin defaults. If
       you want to remove them, use unrestrict default noquery limited to turn off those flags.


       For a detailed description of manycast operation, see the "Server Discovery" page
       (available as part of the HTML documentation).

   Manycast Options
       tos [ceiling ceiling | floor floor | minclock minclock | minsane minsane]
           This command affects the clock selection and clustering algorithms. It can be used to
           select the quality and quantity of peers used to synchronize the system clock and is
           most useful in manycast mode. The variables operate as follows:

           ceiling ceiling
               Peers with strata above ceiling will be discarded if there are at least minclock
               peers remaining. This value defaults to 15, but can be changed to any number from
               1 to 15.

           floor floor
               Peers with strata below floor will be discarded if there are at least minclock
               peers remaining. This value defaults to 1, but can be changed to any number from 1
               to 15.

           minclock minclock
               The clustering algorithm repeatedly casts out outlier associations until no more
               than minclock associations remain. This value defaults to 3, but can be changed to
               any number from 1 to the number of configured sources.

           minsane minsane
               This is the minimum number of candidates available to the clock selection
               algorithm in order to produce one or more truechimers for the clustering
               algorithm. If fewer than this number are available, the clock is undisciplined and
               allowed to run free. The default is 1 for legacy purposes. However, according to
               principles of Byzantine agreement, minsane should be at least 4 in order to detect
               and discard a single falseticker.


       For a detailed description of reference-clock configuration, see the "Reference Clock
       Drivers" page (available as part of the HTML documentation provided in


       refclock drivername [unit u] [prefer] [subtype int] [mode int] [minpoll int] [maxpoll int]
       [time1 sec] [time2 sec] [stratum int] [refid string] [path filename] [ppspath filename]
       [baud number] [flag1 {0 | 1}] [flag2 {0 | 1}] [flag3 {0 | 1}] [flag4 {0 | 1}]
           This command is used to configure reference clocks. The required drivername argument
           is the shortname of a driver type (e.g., shm, nmea, generic; see the Reference Clock
           Drivers <refclock.html> page for a full list. The options are interpreted as follows:

               The 0-origin unit number of the device; this modifies the devicename. If not
               specified, defaults to zero.

               Marks the reference clock as preferred. All other things being equal, this host
               will be chosen for synchronization among a set of correctly operating hosts and
               clocks. See the "Mitigation Rules and the prefer Keyword" page (available as part
               of the HTML documentation provided in /usr/share/doc/ntp) for further information.

           subtype int
               Some drivers (notably the generic and jjy drivers) support multiple device types.
               This option selects among them in a driver-dependent way.

           mode int
               Specifies a mode number which is interpreted in a device-specific fashion. For
               instance, it selects a dialing protocol in the ACTS driver and a sentence mix in
               the nmea driver.

           minpoll int; maxpoll int
               These options specify the minimum and maximum polling interval for reference clock
               messages, as a power of 2 in seconds. For most directly connected reference
               clocks, both minpoll and maxpoll default to 6 (64 sec). For modem reference
               clocks, minpoll defaults to 10 (17.1 min) and maxpoll defaults to 14 (4.5 hours).
               The allowable range is 0 (1 sec) to 17 (36.4 hours) inclusive.

           time1 sec
               Specifies a constant to be added to the time offset produced by the driver, a
               fixed-point decimal number in seconds. Each "g" on the end of the constant adds
               the number of seconds in a 10-bit GPS era; each "G" adds the number of seconds in
               a 13-bit GPS era. This is used as a calibration constant to adjust the nominal
               time offset of a particular clock to agree with an external standard, such as a
               precision PPS signal. It also provides a way to correct a systematic error or bias
               due to era wraparound from a GPS device, serial port or operating system
               latencies, different cable lengths or receiver internal delay. The specified
               offset is in addition to the propagation delay provided by other means, such as
               internal DIP switches. Where a calibration for an individual system and driver is
               available, an approximate correction is noted in the driver documentation pages.
               Note: To facilitate calibration when more than one radio clock or PPS signal is
               supported, a special calibration feature is available. It takes the form of an
               argument to the enable command described in "Miscellaneous Options" page and
               operates as described in the "Reference Clock Drivers" page.

           time2 secs
               Specifies a fixed-point decimal number in seconds, which is interpreted in a
               driver-dependent way. See the descriptions of specific drivers in the "Reference
               Clock Drivers" page.

           stratum int
               Specifies the stratum number assigned to the driver, an integer between 0 and 15.
               This number overrides the default stratum number ordinarily assigned by the driver
               itself, usually zero.

           refid string
               Specifies an ASCII string of from one to four characters which defines the
               reference identifier used by the driver. This string overrides the default
               identifier ordinarily assigned by the driver itself.

           path filepath
               Overrides the default device location for this refclock.

           ppspath filepath
               Overrides the default PPS device location (if any) for this driver.

           baud number
               Overrides the defaults baud rate for this driver.

           flag1 {0 | 1}; flag2 {0 | 1}; flag3 {0 | 1}; flag4 {0 | 1}
               These four flags are used for customizing the clock driver. The interpretation of
               these values, and whether they are used at all, is a function of the particular
               clock driver. However, by convention flag4 is used to enable recording monitoring
               data to the clockstats file configured with the filegen command. Further
               information on the filegen command can be found in "Monitoring Options".


       driftfile driftfile
           This command specifies the complete path and name of the file used to record the
           frequency of the local clock oscillator; this is the same operation as the -f command
           line option. If the file exists, it is read at startup to set the initial frequency
           and then updated once per hour with the current frequency computed by the daemon. If
           the file name is specified, but the file itself does not exist, ntpd starts with an
           initial frequency of zero and creates the file when writing it for the first time. If
           this command is not given, the daemon will always start with an initial frequency of

           The file format consists of a single line containing a single floating point number,
           which records the frequency offset measured in parts-per-million (PPM). The file is
           updated by first writing the current drift value into a temporary file and then
           renaming this file to replace the old version; this implies that ntpd(8) must have
           write permission for the directory the drift file is located in, and that file system
           links, symbolic or otherwise, should be avoided.

       enable [auth | calibrate | kernel | monitor | ntp | stats]; disable [auth | calibrate |
       kernel | monitor | ntp | stats]
           Provides a way to enable or disable various server options. Flags not mentioned are
           unaffected. Note that all of these flags can be controlled remotely using the ntpq(1)
           utility program.

               Enables the server to synchronize with unconfigured peers only if the peer has
               been correctly authenticated. The default for this flag is enable.

               Enables the calibrate feature for reference clocks. The default for this flag is

               Enables the kernel time discipline, if available. The default for this flag is
               enable if support is available, otherwise disable.

               Enables the monitoring facility. See the ntpq(1) program and the monlist command
               for further information. The default for this flag is enable.

               Enables time and frequency discipline. In effect, this switch opens and closes the
               feedback loop, which is useful for testing. The default for this flag is enable.

               Enables the statistics facility. See the "Monitoring Options" section for further
               information. The default for this flag is disable.

       includefile includefile
           This command allows additional configuration commands to be included from a separate
           file. Include files may be nested to a depth of five; upon reaching the end of any
           include file, command processing resumes in the previous configuration file. Relative
           pathnames are evaluated not with respect to the current working directory but with
           respect to the directory name of the last pushed file in the stack. This option is
           useful for sites that run ntpd(8) on multiple hosts, with (mostly) common options
           (e.g., a restriction list).

       interface [listen | ignore | drop] [all | ipv4 | ipv6 | wildcard | name |
           This command controls which network addresses ntpd opens, and whether the input is
           dropped without processing. The first parameter determines the action on addresses
           which match the second parameter. That parameter specifies a class of addresses, or a
           specific interface name, or an address. In the address case, prefixlen determines how
           many bits must match for this rule to apply. ignore prevents opening matching
           addresses, drop causes ntpd to open the address and drop all received packets without
           examination. Multiple interface commands can be used. The last rule which matches a
           particular address determines the action for it. interface commands are disabled if
           any of the -I, --interface,-L, or --novirtualips command-line options are used. If
           none of those options are used, and no interface actions are specified in the
           configuration file, all available network addresses are opened. The nic command is an
           alias for interface.

       leapfile leapfile
           This command loads the NIST leap seconds file and initializes the leapsecond values
           for the next leap second time, expiration time and TAI offset. The file can be
           obtained using ntpleapfetch.

           The leapfile is scanned when ntpd processes the leapfile directive or when ntpd
           detects that leapfile has changed. ntpd checks once a day to see if the leapfile has

       leapsmearinterval interval
           This experimental option is only available if ntpd was built with the
           --enable-leap-smear option, It specifies the interval over which a leap second
           correction will be applied. Recommended values for this option are between 7200 (2
           hours) and 86400 (24 hours). DO NOT USE THIS OPTION ON PUBLIC-ACCESS SERVERS! See
  for more information.

       logconfig configkeyword
           This command controls the amount and type of output written to the system syslog(3)
           facility or the alternate log file. By default, all output is turned on. All
           configkeyword keywords can be prefixed with ‘=’, ‘’ and ‘-’, where ‘=’ sets the
           syslog(3) priority mask, ‘’ adds and ‘-’ removes messages. syslog(3) messages can be
           controlled in four classes (clock,peer,sys and sync). Within these classes four types
           of messages can be controlled: informational messages (info), event messages (events),
           statistics messages (statistics) and status messages (status).

           Configuration keywords are formed by concatenating the message class with the event
           class. The all prefix can be used instead of a message class. A message class may also
           be followed by the all keyword to enable/disable all messages of the respective
           message class. Thus, a minimal log configuration could look like this:

               logconfig =syncstatus +sysevents

           This would just list the synchronizations state of ntpd(8) and the major system
           events. For a simple reference server, the following minimum message configuration
           could be useful:

               logconfig =syncall +clockall

           This configuration will list all clock information and synchronization information.
           All other events and messages about peers, system events and so on is suppressed.

       logfile logfile
           This command specifies the location of an alternate log file to be used instead of the
           default system syslog(3) facility; this is the same operation as the -l command line

       If your ntpd runs for a long time, you probably want to use logrotate or newsyslog to
       switch to a new log file occasionally. SIGHUP will reopen the log file.

       mru [maxdepth count | maxmem kilobytes | mindepth count | maxage seconds | minage seconds
       | initalloc count | initmem kilobytes | incalloc count | incmem kilobytes]
           Controls size limits of the monitoring facility Most Recently Used (MRU) list of
           client addresses, which is also used by the rate control facility.

           maxdepth count, maxmem kilobytes
               Equivalent upper limits on the size of the MRU list, in terms of entries or
               kilobytes. The actual limit will be up to incalloc entries or incmem kilobytes
               larger. As with all of the mru options offered in units of entries or kilobytes,
               if both maxdepth and maxmem are used, the last one used controls. The default is
               1024 kilobytes.

           mindepth count
               The lower limit on the MRU list size. When the MRU list has fewer than mindepth
               entries, existing entries are never removed to make room for newer ones,
               regardless of their age. The default is 600 entries.

           maxage seconds, minage seconds
               If an address is not in the list, there are several possible ways to find a slot
               for it.

                1. If the list has fewer than mindepth entries, a slot is allocated from the free
                   list; this is the normal case for a server without a lot of clients. If
                   clients come and go, for example, laptops going between home and work, the
                   default setup shows only the long term average.

                2. If the age of the oldest slot is greater than maxage, the oldest slot is
                   recycled (default 3600 seconds).

                3. If the freelist is not empty, a slot is allocated from the free list.

                4. If the freelist is empty but not full (see maxmem), more memory is allocated
                   (see incmem) and, a new slot is used.

                5. If the age of the oldest slot is more than minage, the oldest slot is recycled
                   (default 64 seconds).

                6. Otherwise, no slot is available.

           initalloc count, initmem kilobytes
               Initial memory allocation at the time the monitoring facility is first enabled, in
               terms of entries or kilobytes. The default is 4 kilobytes.

           incalloc count, incmem kilobytes
               Size of additional memory allocations when growing the MRU list, in entries or
               kilobytes. The default is 4 kilobytes.

       nonvolatile threshold
           Specify the threshold in seconds to write the frequency file, with a default of 1e-7
           (0.1 PPM). The frequency file is inspected each hour. If the difference between the
           current frequency and the last value written exceeds the threshold, the file is
           written, and the threshold becomes the new threshold value. If the threshold is not
           exceeded, it is reduced by half; this is intended to reduce the frequency of
           unnecessary file writes for embedded systems with nonvolatile memory.

       phone dial ...
           This command is used in conjunction with the ACTS modem driver (type modem) or the JJY
           driver (type jjy). For ACTS, the arguments consist of a maximum of 10 telephone
           numbers used to dial USNO, NIST or European time services. For the jjy driver in modes
           100-180, the argument is one telephone number used to dial the telephone JJY service.
           The Hayes command ATDT is normally prepended to the number, which can contain other
           modem control codes as well.

       reset [allpeers] [auth] [ctl] [io] [mem] [sys] [timer]
           Reset one or more groups of counters maintained by ntpd and exposed by ntpq.

       setvar variable [default]
           This command adds a system variable. These variables can be used to distribute
           additional information such as the access policy. If the variable of the form
           name=value is followed by the default keyword, the variable will be listed as part of
           the default system variables (ntpq(1) rv command). These additional variables serve
           informational purposes only. They are not related to the protocol other that they can
           be listed. The known protocol variables will always override any variables defined via
           the setvar mechanism. There are three special variables that contain the names of all
           variable of the same group. The sys_var_list holds the names of all system variables.
           The peer_var_list holds the names of all peer variables and the clock_var_list holds
           the names of the reference clock variables.

       tinker [allan allan | dispersion dispersion | freq freq | huffpuff huffpuff | panic panic
       | step step | stepback stepback | stepfwd stepfwd | stepout stepout]
           This command can be used to alter several system variables in very exceptional
           circumstances. It should occur in the configuration file before any other
           configuration options. The default values of these variables have been carefully
           optimized for a wide range of network speeds and reliability expectations. In general,
           they interact in intricate ways that are hard to predict, and some combinations can
           result in some very nasty behavior. Very rarely is it necessary to change the default
           values; but, some folks cannot resist twisting the knobs anyway, and this command is
           for them. Emphasis added: twisters are on their own and can expect no help from the
           support group.

           The variables operate as follows:

           allan allan
               The argument becomes the new value for the minimum Allan intercept, which is a
               parameter of the PLL/FLL clock discipline algorithm. The value in log2 seconds
               defaults to 11 (2048 s), which is also the lower limit.

           dispersion dispersion
               The argument becomes the new value for the dispersion increase rate, normally
               .000015 s/s.

           freq freq
               The argument becomes the initial value of the frequency offset in
               parts-per-million; this overrides the value in the frequency file, if present, and
               avoids the initial training state if it is not.

           huffpuff huffpuff
               The argument becomes the new value for the experimental huff-n'-puff filter span,
               which determines the most recent interval the algorithm will search for a minimum
               delay. The lower limit is 900 s (15 m), but a more reasonable value is 7200 (2
               hours). There is no default since the filter is not enabled unless this command is

           panic panic
               The argument is the panic threshold, normally 1000 s. If set to zero, the panic
               sanity check is disabled, and a clock offset of any value will be accepted.

           step step
               The argument is the step threshold, which by default is 0.128 sec. It can be set
               to any positive number in seconds. If set to zero, step adjustments will never
               occur. Note: The kernel time discipline is disabled if the step threshold is set
               to zero or greater than the default.

           stepback stepback
               The argument is the step threshold for the backward direction, which by default is
               0.128 sec. It can be set to any positive number in seconds. If both the forward
               and backward step thresholds are set to zero, step adjustments will never occur.
               Note: The kernel time discipline is disabled if each direction of step threshold
               are either set to zero or greater than .5 second.

           stepfwd stepfwd
               As for stepback, but for the forward direction.

           stepout stepout
               The argument is the stepout timeout, which by default is 900 s. It can be set to
               any positive number in seconds. If set to zero, the stepout pulses will not be

       rlimit [memlock megabytes | stacksize 4kPages | filenum filedescriptors]

           memlock megabytes
               Ignored for backward compatibility.

           stacksize 4kPages
               Specifies the maximum size of the process stack on systems with the mlockall()
               function. Defaults to 50 4k pages.

           filenum filedescriptors
               Specifies the maximum number of file descriptors ntpd may have open at once.
               Defaults to the system default.


           the default name of the configuration file

           private keys

       One of the following exit values will be returned:

       0 (EXIT_SUCCESS)
           Successful program execution.

       1 (EXIT_FAILURE)
           The operation failed or the command syntax was not valid.


       ntpd(8), ntpq(1).

       In addition to the manual pages provided, comprehensive documentation is available on the
       world wide web at A snapshot of this documentation is available in
       HTML format in /usr/share/doc/ntp.

       David L. Mills, Network Time Protocol (Version 4), RFC 5905


       The syntax checking is not picky; some combinations of ridiculous and even hilarious
       options and modes may not be detected.