Ubuntu Manpage: weston-drm - the DRM backend for Weston

NAME

       weston-drm - the DRM backend for Weston

SYNOPSIS

       weston-launch

       weston --backend=drm-backend.so

DESCRIPTION

The DRM backend is the native Weston backend for systems that support the Linux kernel
DRM, kernel mode setting (KMS), and evdev input devices. It is the recommended backend
for desktop PCs, and aims to provide the full Wayland experience with the "every frame is
perfect" concept. It also relies on the Mesa GBM interface.

With the DRM backend, weston runs without any underlying windowing system. The backend
uses the Linux KMS API to detect connected monitors. Monitor hot-plugging is supported.
Input devices are found automatically by udev(7). Compositing happens mainly in GL ES 2,
initialized through EGL. It is also possible to take advantage of hardware cursors and
overlays, when they exist and are functional. Full-screen surfaces will be scanned out
directly without compositing, when possible. Hardware accelerated clients are supported
via EGL.

The backend chooses the DRM graphics device first based on seat id. If seat identifiers
are not set, it looks for the graphics device that was used in boot. If that is not found,
it finally chooses the first DRM device returned by udev(7). Combining multiple graphics
devices is not supported yet.

The DRM backend relies on weston-launch for managing input device access and DRM master
status, so that weston can be run without root privileges. On switching away from the
virtual terminal (VT) hosting Weston, all input devices are closed and the DRM master
capability is dropped, so that other servers, including Xorg(1), can run on other VTs. On
switching back to Weston's VT, input devices and DRM master are re-acquired through the
parent process weston-launch.

The DRM backend also supports virtual outputs that are transmitted over an RTP session as
a series of JPEG images (RTP payload type 26) to a remote client. Virtual outputs are
configured in the remote-output section of weston.ini.

CONFIGURATION

The DRM backend uses the following entries from weston.ini.

Section output
name=connector
The KMS connector name identifying the output, for instance LVDS1.

mode=mode
Specify the video mode for the output. The argument mode can be one of the words
off to turn the output off, preferred to use the monitor's preferred video mode, or
current to use the current video mode and avoid a mode switch. It can also be a
resolution as:

mode=widthxheight

mode=widthxheight@refresh_rate
Specify a mode with a given refresh-rate measured in Hz.

mode=widthxheight@refresh_rate ratio
Here ratio is Picture Aspect-Ratio which can have values as 4:3, 16:9, 64:27, and
256:135. This resolution-format helps to select a CEA mode, if such a video mode is
present in the mode-list of the output.

CEA defines the timing of a video mode, which is considered as a standard for HDMI
spcification and compliance testing. It defines each and every parameter of a video
mode, like hactive, vactive, vfront, vback etc., including aspect-ratio
information. For CEA modes, the drm layer, stores this aspect-ratio information in
user-mode (drmModeModeInfo) flag bits 19-22. For the non-CEA modes a value of 0 is
stored in the aspect-ratio flag bits.

Each CEA-mode is identified by a unique, Video Identification Code (VIC). For
example, VIC=4 is 1280x720@60 aspect-ratio 16:9. This mode will be different than a
non-CEA mode 1280x720@60 0:0. When the video mode 1280x720@60 0:0 is applied, since
its timing doesn't exactly match with the CEA information for VIC=4, it would be
treated as a non-CEA mode. Also, while setting the HDMI-AVI-Inforframe, VIC
parameter will be given as '0'. If video mode 1280x720@60 16:9 is applied, its CEA
timimgs matches with that of video mode with VIC=4, so the VIC parameter in HDMI-
AVI-Infoframe will be set to 4.

Many a times, an output may have both CEA and non-CEA modes, which are similar in
all resepct, differing only in the aspect-ratio. A user can select a CEA mode by
giving the aspect-ratio, along with the other arguments for the mode. By omitting
the aspect-ratio, user can specify the non-CEA modes. This helps when
certification testing is done, in tests like 7-27, the HDMI-analyzer applies a
particular CEA mode, and expects the applied mode to be with exactly same timings,
including the aspect-ratio and VIC field.

The resolution can also be a detailed mode line as below.

mode=dotclock hdisp hsyncstart hsyncend htotal vdisp vsyncstart vsyncend vtotal hflag
vflag
Use the given detailed mode line as the video mode for this output. The definition
is the same as in xorg.conf(5), and cvt(1) can generate detailed mode lines.

transform=transform
Transform for the output, which can be rotated in 90-degree steps and possibly
flipped. Possible values are normal, rotate-90, rotate-180, rotate-270, flipped,
flipped-rotate-90, flipped-rotate-180, and flipped-rotate-270.

pixman-shadow=boolean
If using the Pixman-renderer, use shadow framebuffers. Defaults to true.

same-as=name
Make this output (connector) a clone of another. The argument name is the name
value of another output section. The referred to output section must exist. When
this key is present in an output section, all other keys have no effect on the
configuration.

NOTE: cms-colord plugin does not work correctly with this option. The plugin
chooses an arbitrary monitor to load the color profile for, but the profile is
applied equally to all cloned monitors regardless of their properties.

force-on=true
Force the output to be enabled even if the connector is disconnected. Defaults to
false. Note that mode=off will override force-on=true. When a connector is
disconnected, there is no EDID information to provide a list of video modes.
Therefore a forced output should also have a detailed mode line specified.

Section remote-output
name=name
Specify unique name for the output.

mode=mode
Specify the video mode for the output. The argument mode is a resolution setting,
such as:

mode=widthxheight

mode=widthxheight@refresh_rate
If refresh_rate is not specified it will default to a 60Hz.

host=host
Specify the host name or IP Address that the remote output will be transmitted to.

port=port
Specify the port number to transmit the remote output to. Usable port range is
1-65533.

gst-pipeline=pipeline
Specify the gstreamer pipeline. It is necessary that source is appsrc, its name is
"src", and sink name is "sink" in pipeline. Ignore port and host configuration if
the gst-pipeline is specified.

OPTIONS

       When  the  DRM  backend is loaded, weston will understand the following additional command
       line options.

       --current-mode
              By default, use the current video mode of all outputs, instead of switching to  the
              monitor preferred mode.

       --drm-device=cardN
              Use  the  DRM  device  cardN  instead  of  the  default  heuristics  based  on seat
              assignments and boot VGA status. For example, use card0.

       --seat=seatid
              Use graphics and input devices designated for  seat  seatid  instead  of  the  seat
              defined  in  the environment variable XDG_SEAT. If neither is specified, seat0 will
              be assumed.

       --tty=x
              Launch Weston on tty x instead of using the current tty.

       --continue-without-input
              Allow Weston to start without input devices. Used for testing purposes.

ENVIRONMENT