NAME

       cryptsetup-luksRemoveKey - remove the supplied passphrase from the LUKS device

SYNOPSIS

       cryptsetup luksRemoveKey [<options>] <device> [<key file with passphrase to be removed>]

DESCRIPTION

       Removes the supplied passphrase from the LUKS device. The passphrase to be removed can be
       specified interactively, as the positional argument or via --key-file.

       <options> can be [--key-file, --keyfile-offset, --keyfile-size, --header, --disable-locks,
       --type, --timeout, --verify-passphrase].

       WARNING: If you read the passphrase from stdin (without further argument or with '-' as an
       argument to --key-file), batch-mode (-q) will be implicitly switched on and no warning
       will be given when you remove the last remaining passphrase from a LUKS container.
       Removing the last passphrase makes the LUKS container permanently inaccessible.

OPTIONS

       --type <device-type>
           Specifies required device type, for more info read BASIC ACTIONS section in
           cryptsetup(8).

       --verify-passphrase, -y
           When interactively asking for a passphrase, ask for it twice and complain if both
           inputs do not match. Ignored on input from file or stdin.

       --key-file, -d name
           Read the passphrase from file.

           If the name given is "-", then the passphrase will be read from stdin. In this case,
           reading will not stop at newline characters.

           With LUKS, the passphrase supplied via --key-file is always the existing passphrase
           requested by a command, except in the case of luksFormat where --key-file is
           equivalent to the positional key file argument.

           If you want to set a new passphrase via key file, you have to use a positional
           argument to luksAddKey.

           See section NOTES ON PASSPHRASE PROCESSING in cryptsetup(8) for more information.

       --keyfile-offset value
           Skip value bytes at the beginning of the key file.

       --keyfile-size, -l value
           Read a maximum of value bytes from the key file. The default is to read the whole file
           up to the compiled-in maximum that can be queried with --help. Supplying more data
           than the compiled-in maximum aborts the operation.

           This option is useful to cut trailing newlines, for example. If --keyfile-offset is
           also given, the size count starts after the offset.

       --timeout, -t <number of seconds>
           The number of seconds to wait before timeout on passphrase input via terminal. It is
           relevant every time a passphrase is asked. It has no effect if used in conjunction
           with --key-file.

           This option is useful when the system should not stall if the user does not input a
           passphrase, e.g. during boot. The default is a value of 0 seconds, which means to wait
           forever.

       --header <device or file storing the LUKS header>
           Use a detached (separated) metadata device or file where the LUKS header is stored.
           This option allows one to store ciphertext and LUKS header on different devices.

           For commands that change the LUKS header (e.g. luksAddKey), specify the device or file
           with the LUKS header directly as the LUKS device.

       --disable-locks
           Disable lock protection for metadata on disk. This option is valid only for LUKS2 and
           ignored for other formats.

           WARNING: Do not use this option unless you run cryptsetup in a restricted environment
           where locking is impossible to perform (where /run directory cannot be used).

       --batch-mode, -q
           Suppresses all confirmation questions. Use with care!

           If the --verify-passphrase option is not specified, this option also switches off the
           passphrase verification.

       --debug or --debug-json
           Run in debug mode with full diagnostic logs. Debug output lines are always prefixed by
           #.

           If --debug-json is used, additional LUKS2 JSON data structures are printed.

       --version, -V
           Show the program version.

       --usage
           Show short option help.

       --help, -?
           Show help text and default parameters.

REPORTING BUGS

       Report bugs at cryptsetup mailing list <cryptsetup@lists.linux.dev> or in Issues project
       section <https://gitlab.com/cryptsetup/cryptsetup/-/issues/new>.

       Please attach output of the failed command with --debug option added.

SEE ALSO

       Cryptsetup FAQ <https://gitlab.com/cryptsetup/cryptsetup/wikis/FrequentlyAskedQuestions>

       cryptsetup(8), integritysetup(8) and veritysetup(8)

CRYPTSETUP

       Part of cryptsetup project <https://gitlab.com/cryptsetup/cryptsetup/>.