Provided by: tcpspy_1.7d-15_amd64 bug

NAME

       tcpspy - TCP/IP Connection Monitor

SYNOPSIS

       tcpspy  [-dp]  [-e  rule]...   [-f rulefile]...  [-F facility] [-I interval] [-U user] [-G
       group]

DESCRIPTION

       tcpspy logs information about selected incoming and outgoing TCP/IP connections to syslog.
       The  following  information  is  logged: username, local address and port, remote address,
       port, and optionally the filename of the executable.

   Options
       -e 'rule'
              Log only connections matching the specified rule. Rule syntax is outlined below. If
              this  option is specified more than once, connections matching any of the specified
              rules are logged. You should quote the rule, as shown above.

       -f rulefile
              Read rules from rulefile.  Each rule is on a new line. The  `#'  character  may  be
              used  to  add  comments;  everything  from this character to the end of the line is
              ignored.

              The -e and -f options may be used together.

       -F facility
              Log to syslog facility facility instead of the compile-time  default  setting.  See
              the syslog.conf(5) manual page for a list of facilities.

       -I interval
              Update  the  internal  state every interval milliseconds, instead of the default of
              1000 ms. Connections that last less than interval milliseconds may  be  missed,  so
              you  should  experiment  to  find  a  value  small  enough  that  it  catches  most
              connections, but not so small that it causes tcpspy to use too much CPU time.

       -U user
              Switch to the specified user after startup.  user may be a numeric  user  id  or  a
              user name from the system password file.

       -G group
              Switch  to the specified group after startup.  group may be a numeric group id or a
              group name from the system group file.  If a username to  switch  to  with  the  -U
              option  is specified but -G is omitted, tcpspy will switch to that specified user's
              primary group.

       -d     Debugging mode; if this option is  specified,  tcpspy  will  not  detach  from  the
              console  after  initialisation, and will log connections to standard output instead
              of syslog.

       -p     Log the filename of the executable that created/accepted the connection.   You  may
              require  superuser  privileges  to obtain this information for processes you do not
              own (this is a kernel limitation).

              This option can greatly increase the amount of CPU time required  to  process  each
              connection/disconnection.

   Rule Syntax
       A  rule  may be specified with the -e option to log information about connections matching
       this rule, overriding the default of logging all connections.

       The following comparison operations are defined:

       user uid
              True if the local user initiating or accepting the  connection  has  the  effective
              user id uid.

       user "username"
              Same as above, but using a username instead of a user id.

       ip     True if the connection is IPv4.

       ip6    True if the connection is IPv6.

       lport port
              True if the local end of the connection has port number port.

       lport [low] - [high]
              True  if the local end of the connection has a port number greater than or equal to
              low and less than or equal to high.  If the form low- is used, high is  assumed  to
              be  65535.   If  the  form -high is used, low is assumed to be 0. It is an error to
              omit both low and high.

       lport "service"
              Same as above, but using a service  name  from  /etc/services  instead  of  a  port
              number.

       rport  Same as lport but compares the port number of the remote end of the connection.

       laddr n.n.n.n[/m.m.m.m]

       laddr n.n.n.n/m

       laddr ip6-addr[/m]
              Interpreted  as  a "net/mask" expression; true if "net" is equal to the bitwise AND
              of the local address of the connection and "mask".  If  no  mask  is  specified,  a
              default  mask with all bits set (255.255.255.255) is used. The CIDR type netmask is
              also possible. With IPv6 only a prefix length netmask is allowed,  and  the  length
              defaults  to  128. Depending on the address family, these rules contain an implicit
              match condition "ip" or "ip6", respectively.

       raddr  Same as laddr but compares the remote address.

       exe "pattern"
              True  if  the  full  filename  (including  directory)  of   the   executable   that
              created/accepted the connection matches pattern, a glob(7)-style wildcard pattern.

              The  pattern "" (an empty string) matches connections created/accepted by processes
              whose executable filename is unknown.

              If the -p option is not specified, a warning  message  will  be  printed,  and  the
              result of this comparison will always be true.

       Expressions  (including  the   comparisons  listed  above) may be joined together with the
       following logical operations:

       expr1 or expr2
              True if either of expr1 or expr2 are true (logical OR).

       expr1 and expr2
              True if both expr1 and expr2 are true (logical AND).

       not expr
              True if expr is false (logical NOT).

       Rules are evaluated from left to right. Whitespace (space, tab and newline) characters are
       ignored  between "words". Rules consisting of only whitespace match no connections, but do
       not cause an error.  Parentheses, '(' and ')' may be placed around expressions  to  affect
       the order of evaluation.

       The  Examples  section  contains  some sample rules which further demonstrate how they are
       constructed.

EXIT STATUS

       0      The daemon was successfully started

       >0     An error occurred

SIGNALS

       TERM   Shut down at most interval milliseconds from now.

       INT    (Debugging mode only) Handled identically to TERM.

       All other signals retain their default behaviour, which is documented in signal(7).

EXAMPLES

       tcpspy -e 'user "joe" and rport "ssh"'
              Log connections made by user "joe" for the service "ssh".

       tcpspy -e 'not raddr 10.0.0.0/255.0.0.0 and rport 25 and (user "bob" or user "joe")'
              Log connections made by users "bob" and "joe" to remote port 25 on machines not  on
              a fictional "intranet".

       tcpspy -e 'exe "/usr/bin/irc"'
              Log connections made by /usr/bin/irc (probably ircII).

BUGS

       Empty rule files cause tcpspy to log no connections instead of all connections.

AUTHOR

       Tim J. Robbins <tim@robbins.dropbear.id.au>

SEE ALSO

       glob(7), proc(5), services(5), signal(7), syslog(3), syslog.conf(5), tcpspy.rules(5)