Provided by: avr-libc_2.0.0+Atmel3.6.2-3_all bug

NAME

       avr_sleep - <avr/sleep.h>: Power Management and Sleep Modes

SYNOPSIS

   Functions
       void sleep_enable (void)
       void sleep_disable (void)
       void sleep_cpu (void)
       void sleep_mode (void)
       void sleep_bod_disable (void)

Detailed Description

       #include <avr/sleep.h>

       Use of the SLEEP instruction can allow an application to reduce its power comsumption
       considerably. AVR devices can be put into different sleep modes. Refer to the datasheet
       for the details relating to the device you are using.

       There are several macros provided in this header file to actually put the device into
       sleep mode. The simplest way is to optionally set the desired sleep mode using
       set_sleep_mode() (it usually defaults to idle mode where the CPU is put on sleep but all
       peripheral clocks are still running), and then call sleep_mode(). This macro automatically
       sets the sleep enable bit, goes to sleep, and clears the sleep enable bit.

       Example:

       #include <avr/sleep.h>

       ...
         set_sleep_mode(<mode>);
         sleep_mode();

       Note that unless your purpose is to completely lock the CPU (until a hardware reset),
       interrupts need to be enabled before going to sleep.

       As the sleep_mode() macro might cause race conditions in some situations, the individual
       steps of manipulating the sleep enable (SE) bit, and actually issuing the SLEEP
       instruction, are provided in the macros sleep_enable(), sleep_disable(), and sleep_cpu().
       This also allows for test-and-sleep scenarios that take care of not missing the interrupt
       that will awake the device from sleep.

       Example:

       #include <avr/interrupt.h>
       #include <avr/sleep.h>

       ...
         set_sleep_mode(<mode>);
         cli();
         if (some_condition)
         {
           sleep_enable();
           sei();
           sleep_cpu();
           sleep_disable();
         }
         sei();

       This sequence ensures an atomic test of some_condition with interrupts being disabled. If
       the condition is met, sleep mode will be prepared, and the SLEEP instruction will be
       scheduled immediately after an SEI instruction. As the intruction right after the SEI is
       guaranteed to be executed before an interrupt could trigger, it is sure the device will
       really be put to sleep.

       Some devices have the ability to disable the Brown Out Detector (BOD) before going to
       sleep. This will also reduce power while sleeping. If the specific AVR device has this
       ability then an additional macro is defined: sleep_bod_disable(). This macro generates
       inlined assembly code that will correctly implement the timed sequence for disabling the
       BOD before sleeping. However, there is a limited number of cycles after the BOD has been
       disabled that the device can be put into sleep mode, otherwise the BOD will not truly be
       disabled. Recommended practice is to disable the BOD (sleep_bod_disable()), set the
       interrupts (sei()), and then put the device to sleep (sleep_cpu()), like so:

       #include <avr/interrupt.h>
       #include <avr/sleep.h>

       ...
         set_sleep_mode(<mode>);
         cli();
         if (some_condition)
         {
           sleep_enable();
           sleep_bod_disable();
           sei();
           sleep_cpu();
           sleep_disable();
         }
         sei();

Function Documentation

   void sleep_bod_disable (void)
       Disable BOD before going to sleep. Not available on all devices.

   void sleep_cpu (void)
       Put the device into sleep mode. The SE bit must be set beforehand, and it is recommended
       to clear it afterwards.

   void sleep_disable (void)
       Clear the SE (sleep enable) bit.

   void sleep_enable (void)
       Put the device in sleep mode. How the device is brought out of sleep mode depends on the
       specific mode selected with the set_sleep_mode() function. See the data sheet for your
       device for more details.

       Set the SE (sleep enable) bit.

   void sleep_mode (void)
       Put the device into sleep mode, taking care of setting the SE bit before, and clearing it
       afterwards.

Author

       Generated automatically by Doxygen for avr-libc from the source code.