Provided by: systemtap-doc_4.7-1_amd64 
NAME
stapprobes - systemtap probe points
DESCRIPTION
The following sections enumerate the variety of probe points supported by the systemtap
translator, and some of the additional aliases defined by standard tapset scripts. Many
are individually documented in the 3stap manual section, with the probe:: prefix.
SYNTAX
probe PROBEPOINT [, PROBEPOINT] { [STMT ...] }
A probe declaration may list multiple comma-separated probe points in order to attach a
handler to all of the named events. Normally, the handler statements are run whenever any
of events occur. Depending on the type of probe point, the handler statements may refer
to context variables (denoted with a dollar-sign prefix like $foo) to read or write state.
This may include function parameters for function probes, or local variables for statement
probes.
The syntax of a single probe point is a general dotted-symbol sequence. This allows a
breakdown of the event namespace into parts, somewhat like the Domain Name System does on
the Internet. Each component identifier may be parametrized by a string or number
literal, with a syntax like a function call. A component may include a "*" character, to
expand to a set of matching probe points. It may also include "**" to match multiple
sequential components at once. Probe aliases likewise expand to other probe points.
Probe aliases can be given on their own, or with a suffix. The suffix attaches to the
underlying probe point that the alias is expanded to. For example,
syscall.read.return.maxactive(10)
expands to
kernel.function("sys_read").return.maxactive(10)
with the component maxactive(10) being recognized as a suffix.
Normally, each and every probe point resulting from wildcard- and alias-expansion must be
resolved to some low-level system instrumentation facility (e.g., a kprobe address,
marker, or a timer configuration), otherwise the elaboration phase will fail.
However, a probe point may be followed by a "?" character, to indicate that it is
optional, and that no error should result if it fails to resolve. Optionalness passes
down through all levels of alias/wildcard expansion. Alternately, a probe point may be
followed by a "!" character, to indicate that it is both optional and sufficient. (Think
vaguely of the Prolog cut operator.) If it does resolve, then no further probe points in
the same comma-separated list will be resolved. Therefore, the "!" sufficiency mark only
makes sense in a list of probe point alternatives.
Additionally, a probe point may be followed by a "if (expr)" statement, in order to
enable/disable the probe point on-the-fly. With the "if" statement, if the "expr" is false
when the probe point is hit, the whole probe body including alias's body is skipped. The
condition is stacked up through all levels of alias/wildcard expansion. So the final
condition becomes the logical-and of conditions of all expanded alias/wildcard. The
expressions are necessarily restricted to global variables.
These are all syntactically valid probe points. (They are generally semantically invalid,
depending on the contents of the tapsets, and the versions of kernel/user software
installed.)
kernel.function("foo").return
process("/bin/vi").statement(0x2222)
end
syscall.*
syscall.*.return.maxactive(10)
syscall.{open,close}
sys**open
kernel.function("no_such_function") ?
module("awol").function("no_such_function") !
signal.*? if (switch)
kprobe.function("foo")
Probes may be broadly classified into "synchronous" and "asynchronous". A "synchronous"
event is deemed to occur when any processor executes an instruction matched by the
specification. This gives these probes a reference point (instruction address) from which
more contextual data may be available. Other families of probe points refer to
"asynchronous" events such as timers/counters rolling over, where there is no fixed
reference point that is related. Each probe point specification may match multiple
locations (for example, using wildcards or aliases), and all them are then probed. A
probe declaration may also contain several comma-separated specifications, all of which
are probed.
Brace expansion is a mechanism which allows a list of probe points to be generated. It is
very similar to shell expansion. A component may be surrounded by a pair of curly braces
to indicate that the comma-separated sequence of one or more subcomponents will each
constitute a new probe point. The braces may be arbitrarily nested. The ordering of
expanded results is based on product order.
The question mark (?), exclamation mark (!) indicators and probe point conditions may not
be placed in any expansions that are before the last component.
The following is an example of brace expansion.
syscall.{write,read}
# Expands to
syscall.write, syscall.read
{kernel,module("nfs")}.function("nfs*")!
# Expands to
kernel.function("nfs*")!, module("nfs").function("nfs*")!
DWARF DEBUGINFO
Resolving some probe points requires DWARF debuginfo or "debug symbols" for the specific
program being instrumented. For some others, DWARF is automatically synthesized on the
fly from source code header files. For others, it is not needed at all. Since a
systemtap script may use any mixture of probe points together, the union of their DWARF
requirements has to be met on the computer where script compilation occurs. (See the
--use-server option and the stap-server(8) man page for information about the remote
compilation facility, which allows these requirements to be met on a different machine.)
The following point lists many of the available probe point families, to classify them
with respect to their need for DWARF debuginfo for the specific program for that probe
point.
DWARF NON-DWARF SYMBOL-TABLE
kernel.function, .statement kernel.mark kernel.function*
module.function, .statement process.mark, process.plt module.function*
process.function, .statement begin, end, error, never process.function*
process.mark* timer
.function.callee perf
python2, python3 procfs
kernel.statement.absolute
AUTO-GENERATED-DWARF kernel.data
kprobe.function
kernel.trace process.statement.absolute
process.begin, .end
netfilter
java
The probe types marked with * asterisks mark fallbacks, where systemtap can sometimes
infer subset or substitute information. In general, the more symbolic / debugging
information available, the higher quality probing will be available.
ON-THE-FLY ARMING
The following types of probe points may be armed/disarmed on-the-fly to save overheads
during uninteresting times. Arming conditions may also be added to other types of probes,
but will be treated as a wrapping conditional and won't benefit from overhead savings.
DISARMABLE exceptions
kernel.function, kernel.statement
module.function, module.statement
process.*.function, process.*.statement
process.*.plt, process.*.mark
timer. timer.profile
java
PROBE POINT FAMILIES
BEGIN/END/ERROR
The probe points begin and end are defined by the translator to refer to the time of
session startup and shutdown. All "begin" probe handlers are run, in some sequence,
during the startup of the session. All global variables will have been initialized prior
to this point. All "end" probes are run, in some sequence, during the normal shutdown of
a session, such as in the aftermath of an exit () function call, or an interruption from
the user. In the case of an error-triggered shutdown, "end" probes are not run. There
are no target variables available in either context.
If the order of execution among "begin" or "end" probes is significant, then an optional
sequence number may be provided:
begin(N)
end(N)
The number N may be positive or negative. The probe handlers are run in increasing order,
and the order between handlers with the same sequence number is unspecified. When "begin"
or "end" are given without a sequence, they are effectively sequence zero.
The error probe point is similar to the end probe, except that each such probe handler run
when the session ends after errors have occurred. In such cases, "end" probes are
skipped, but each "error" probe is still attempted. This kind of probe can be used to
clean up or emit a "final gasp". It may also be numerically parametrized to set a
sequence.
NEVER
The probe point never is specially defined by the translator to mean "never". Its probe
handler is never run, though its statements are analyzed for symbol / type correctness as
usual. This probe point may be useful in conjunction with optional probes.
SYSCALL and ND_SYSCALL
The syscall.* and nd_syscall.* aliases define several hundred probes, too many to detail
here. They are of the general form:
syscall.NAME
nd_syscall.NAME
syscall.NAME.return
nd_syscall.NAME.return
Generally, a pair of probes are defined for each normal system call as listed in the
syscalls(2) manual page, one for entry and one for return. Those system calls that never
return do not have a corresponding .return probe. The nd_* family of probes are about the
same, except it uses non-DWARF based searching mechanisms, which may result in a lower
quality of symbolic context data (parameters), and may miss some system calls. You may
want to try them first, in case kernel debugging information is not immediately available.
Each probe alias provides a variety of variables. Looking at the tapset source code is the
most reliable way. Generally, each variable listed in the standard manual page is made
available as a script-level variable, so syscall.open exposes filename, flags, and mode.
In addition, a standard suite of variables is available at most aliases:
argstr A pretty-printed form of the entire argument list, without parentheses.
name The name of the system call.
retval For return probes, the raw numeric system-call result.
retstr For return probes, a pretty-printed string form of the system-call result.
As usual for probe aliases, these variables are all initialized once from the underlying
$context variables, so that later changes to $context variables are not automatically
reflected. Not all probe aliases obey all of these general guidelines. Please report any
bothersome ones you encounter as a bug. Note that on some kernel/userspace architecture
combinations (e.g., 32-bit userspace on 64-bit kernel), the underlying $context variables
may need explicit sign extension / masking. When this is an issue, consider using the
tapset-provided variables instead of raw $context variables.
If debuginfo availability is a problem, you may try using the non-DWARF syscall probe
aliases instead. Use the nd_syscall. prefix instead of syscall. The same context
variables are available, as far as possible.
nd_syscall probes on kernels that use syscall wrappers to pass arguments via pt_regs
(currently 4.17+ on x86_64 and 4.19+ on aarch64) support syscall argument writing when
guru mode is enabled. If a probe syscall parameter is modified in the probe body then
immediately before the probe exits the parameter's current value will be written to
pt_regs. This overwrites the previous value. nd_syscall probes also include two
parameters for each of the syscall's string parameters. One holds a quoted version of the
string passed to the syscall. The other holds an unquoted version of the string intended
to be used when modifying the parameter. If the probe modifies the unquoted string
variable then as the probe is about to exit the contents of this variable will be written
to the user space buffer passed to the syscall. It is the user's responsibility to ensure
that this buffer is large enough to hold the modified string and that it is located in a
writable memory segment.
TIMERS
There are two main types of timer probes: "jiffies" timer probes and time interval timer
probes.
Intervals defined by the standard kernel "jiffies" timer may be used to trigger probe
handlers asynchronously. Two probe point variants are supported by the translator:
timer.jiffies(N)
timer.jiffies(N).randomize(M)
The probe handler is run every N jiffies (a kernel-defined unit of time, typically between
1 and 60 ms). If the "randomize" component is given, a linearly distributed random value
in the range [-M..+M] is added to N every time the handler is run. N is restricted to a
reasonable range (1 to around a million), and M is restricted to be smaller than N. There
are no target variables provided in either context. It is possible for such probes to be
run concurrently on a multi-processor computer.
Alternatively, intervals may be specified in units of time. There are two probe point
variants similar to the jiffies timer:
timer.ms(N)
timer.ms(N).randomize(M)
Here, N and M are specified in milliseconds, but the full options for units are seconds
(s/sec), milliseconds (ms/msec), microseconds (us/usec), nanoseconds (ns/nsec), and hertz
(hz). Randomization is not supported for hertz timers.
The actual resolution of the timers depends on the target kernel. For kernels prior to
2.6.17, timers are limited to jiffies resolution, so intervals are rounded up to the
nearest jiffies interval. After 2.6.17, the implementation uses hrtimers for tighter
precision, though the actual resolution will be arch-dependent. In either case, if the
"randomize" component is given, then the random value will be added to the interval before
any rounding occurs.
Profiling timers are also available to provide probes that execute on all CPUs at the rate
of the system tick (CONFIG_HZ) or at a given frequency (hz). On some kernels, this is a
one-concurrent-user-only or disabled facility, resulting in error -16 (EBUSY) during probe
registration.
timer.profile.tick
timer.profile.freq.hz(N)
Full context information of the interrupted process is available, making this probe
suitable for a time-based sampling profiler.
It is recommended to use the tapset probe timer.profile rather than timer.profile.tick.
This probe point behaves identically to timer.profile.tick when the underlying
functionality is available, and falls back to using perf.sw.cpu_clock on some recent
kernels which lack the corresponding profile timer facility.
Profiling timers with specified frequencies are only accurate up to around 100 hz. You may
need to provide a larger value to achieve the desired rate.
Note that if a timer probe is set to fire at a very high rate and if the probe body is
complex, succeeding timer probes can get skipped, since the time for them to run has
already passed. Normally systemtap reports missed probes, but it will not report these
skipped probes.
DWARF
This family of probe points uses symbolic debugging information for the target
kernel/module/program, as may be found in unstripped executables, or the separate
debuginfo packages. They allow placement of probes logically into the execution path of
the target program, by specifying a set of points in the source or object code. When a
matching statement executes on any processor, the probe handler is run in that context.
Probe points in the DWARF family can be identified by the target kernel module (or user
process), source file, line number, function name, or some combination of these.
Here is a list of DWARF probe points currently supported:
kernel.function(PATTERN)
kernel.function(PATTERN).call
kernel.function(PATTERN).callee(PATTERN)
kernel.function(PATTERN).callee(PATTERN).return
kernel.function(PATTERN).callee(PATTERN).call
kernel.function(PATTERN).callees(DEPTH)
kernel.function(PATTERN).return
kernel.function(PATTERN).inline
kernel.function(PATTERN).label(LPATTERN)
module(MPATTERN).function(PATTERN)
module(MPATTERN).function(PATTERN).call
module(MPATTERN).function(PATTERN).callee(PATTERN)
module(MPATTERN).function(PATTERN).callee(PATTERN).return
module(MPATTERN).function(PATTERN).callee(PATTERN).call
module(MPATTERN).function(PATTERN).callees(DEPTH)
module(MPATTERN).function(PATTERN).return
module(MPATTERN).function(PATTERN).inline
module(MPATTERN).function(PATTERN).label(LPATTERN)
kernel.statement(PATTERN)
kernel.statement(PATTERN).nearest
kernel.statement(ADDRESS).absolute
module(MPATTERN).statement(PATTERN)
process("PATH").function("NAME")
process("PATH").statement("*@FILE.c:123")
process("PATH").library("PATH").function("NAME")
process("PATH").library("PATH").statement("*@FILE.c:123")
process("PATH").library("PATH").statement("*@FILE.c:123").nearest
process("PATH").function("*").return
process("PATH").function("myfun").label("foo")
process("PATH").function("foo").callee("bar")
process("PATH").function("foo").callee("bar").return
process("PATH").function("foo").callee("bar").call
process("PATH").function("foo").callees(DEPTH)
process(PID).function("NAME")
process(PID).function("myfun").label("foo")
process(PID).plt("NAME")
process(PID).plt("NAME").return
process(PID).statement("*@FILE.c:123")
process(PID).statement("*@FILE.c:123").nearest
process(PID).statement(ADDRESS).absolute
(See the USER-SPACE section below for more information on the process probes.)
The list above includes multiple variants and modifiers which provide additional
functionality or filters. They are:
.function
Places a probe near the beginning of the named function, so that parameters
are available as context variables.
.return
Places a probe at the moment after the return from the named function, so
the return value is available as the "$return" context variable.
.inline
Filters the results to include only instances of inlined functions. Note
that inlined functions do not have an identifiable return point, so .return
is not supported on .inline probes.
.call Filters the results to include only non-inlined functions (the opposite set
of .inline)
.exported
Filters the results to include only exported functions.
.statement
Places a probe at the exact spot, exposing those local variables that are
visible there.
.statement.nearest
Places a probe at the nearest available line number for each line number
given in the statement.
.callee
Places a probe on the callee function given in the .callee modifier, where
the callee must be a function called by the target function given in
.function. The advantage of doing this over directly probing the callee
function is that this probe point is run only when the callee is called from
the target function (add the -DSTAP_CALLEE_MATCHALL directive to override
this when calling stap(1)).
Note that only callees that can be statically determined are available. For
example, calls through function pointers are not available. Additionally,
calls to functions located in other objects (e.g. libraries) are not
available (instead use another probe point). This feature will only work for
code compiled with GCC 4.7+.
.callees
Shortcut for .callee("*"), which places a probe on all callees of the
function.
.callees(DEPTH)
Recursively places probes on callees. For example, .callees(2) will probe
both callees of the target function, as well as callees of those callees.
And .callees(3) goes one level deeper, etc... A callee probe at depth N is
only triggered when the N callers in the callstack match those that were
statically determined during analysis (this also may be overridden using
-DSTAP_CALLEE_MATCHALL).
In the above list of probe points, MPATTERN stands for a string literal that aims to
identify the loaded kernel module of interest. For in-tree kernel modules, the name
suffices (e.g. "btrfs"). The name may also include the "*", "[]", and "?" wildcards to
match multiple in-tree modules. Out-of-tree modules are also supported by specifying the
full path to the ko file. Wildcards are not supported. The file must follow the convention
of being named <module_name>.ko (characters ',' and '-' are replaced by '_').
LPATTERN stands for a source program label. It may also contain "*", "[]", and "?"
wildcards. PATTERN stands for a string literal that aims to identify a point in the
program. It is made up of three parts:
• The first part is the name of a function, as would appear in the nm program's output.
This part may use the "*" and "?" wildcarding operators to match multiple names.
• The second part is optional and begins with the "@" character. It is followed by the
path to the source file containing the function, which may include a wildcard pattern,
such as mm/slab*. If it does not match as is, an implicit "*/" is optionally added
before the pattern, so that a script need only name the last few components of a
possibly long source directory path.
• Finally, the third part is optional if the file name part was given, and identifies
the line number in the source file preceded by a ":" or a "+". The line number is
assumed to be an absolute line number if preceded by a ":", or relative to the
declaration line of the function if preceded by a "+". All the lines in the function
can be matched with ":*". A range of lines x through y can be matched with ":x-y".
Ranges and specific lines can be mixed using commas, e.g. ":x,y-z".
As an alternative, PATTERN may be a numeric constant, indicating an address. Such an
address may be found from symbol tables of the appropriate kernel / module object file.
It is verified against known statement code boundaries, and will be relocated for use at
run time.
In guru mode only, absolute kernel-space addresses may be specified with the ".absolute"
suffix. Such an address is considered already relocated, as if it came from
/proc/kallsyms, so it cannot be checked against statement/instruction boundaries.
CONTEXT VARIABLES
Many of the source-level context variables, such as function parameters, locals, globals
visible in the compilation unit, may be visible to probe handlers. They may refer to
these variables by prefixing their name with "$" within the scripts. In addition, a
special syntax allows limited traversal of structures, pointers, and arrays. More syntax
allows pretty-printing of individual variables or their groups. See also @cast. Note
that variables may be inaccessible due to them being paged out, or for a few other
reasons. See also man error::fault(7stap).
Functions called from DWARF class probe points and from process.mark probes may also refer
to context variables.
$var refers to an in-scope variable or thread local storage variable "var". If it's an
integer-like type, it will be cast to a 64-bit int for systemtap script use.
String-like pointers (char *) may be copied to systemtap string values using the
kernel_string or user_string functions.
@var("varname")
an alternative syntax for $varname
@var("varname","module")
The global variable or global thread local storage variable in scope of the given
module already loaded into the current probed process. Useful to get an exported
variable in a shared library loaded into the process being probed, or a global
variable in a process while a shared library probe is being executed. For user-
space modules only. For example: @var("_r_debug","/lib/ld-linux.so.2")
@var("varname@src/file.c")
refers to the global (either file local or external) variable varname defined when
the file src/file.c was compiled. The CU in which the variable is resolved is the
first CU in the module of the probe point which matches the given file name at the
end and has the shortest file name path (e.g. given @var("foo@bar/baz.c") and CUs
with file name paths src/sub/module/bar/baz.c and src/bar/baz.c the second CU will
be chosen to resolve the (file) global variable foo
@var("varname@src/file.c","module")
The global variable in scope of the given CU, defined in the given module, even if
the variable is static (so the name is not unique without the CU name).
$var->field traversal via a structure's or a pointer's field. This
generalized indirection operator may be repeated to follow more levels. Note that
the . operator is not used for plain structure members, only -> for both purposes.
(This is because "." is reserved for string concatenation.) Also note that for
direct dereferencing of $var pointer {kernel,user}_{char,int,...}($var) should be
used. (Refer to stapfuncs(5) for more details.)
$return
is available in return probes only for functions that are declared with a return
value, which can be determined using @defined($return).
$var[N]
indexes into an array. The index given with a literal number or even an arbitrary
numeric expression.
A number of operators exist for such basic context variable expressions:
$$vars expands to a character string that is equivalent to
sprintf("parm1=%x ... parmN=%x var1=%x ... varN=%x",
parm1, ..., parmN, var1, ..., varN)
for each variable in scope at the probe point. Some values may be printed as =?
if their run-time location cannot be found.
$$locals
expands to a subset of $$vars for only local variables.
$$parms
expands to a subset of $$vars for only function parameters.
$$return
is available in return probes only. It expands to a string that is equivalent to
sprintf("return=%x", $return) if the probed function has a return value, or else an
empty string.
& $EXPR
expands to the address of the given context variable expression, if it is
addressable.
@defined($EXPR)
expands to 1 or 0 iff the given context variable expression is resolvable, for use
in conditionals such as
@defined($foo->bar) ? $foo->bar : 0
@probewrite($VAR)
see the PROBES section of stap(1).
$EXPR$ expands to a string with all of $EXPR's members, equivalent to
sprintf("{.a=%i, .b=%u, .c={...}, .d=[...]}",
$EXPR->a, $EXPR->b)
$EXPR$$
expands to a string with all of $var's members and submembers, equivalent to
sprintf("{.a=%i, .b=%u, .c={.x=%p, .y=%c}, .d=[%i, ...]}",
$EXPR->a, $EXPR->b, $EXPR->c->x, $EXPR->c->y, $EXPR->d[0])
@errno expands to the last value the C library global variable errno was set to.
MORE ON RETURN PROBES
For the kernel ".return" probes, only a certain fixed number of returns may be
outstanding. The default is a relatively small number, on the order of a few times the
number of physical CPUs. If many different threads concurrently call the same blocking
function, such as futex(2) or read(2), this limit could be exceeded, and skipped
"kretprobes" would be reported by "stap -t". To work around this, specify a
probe FOO.return.maxactive(NNN)
suffix, with a large enough NNN to cover all expected concurrently blocked threads.
Alternately, use the
stap -DKRETACTIVE=NNNN
stap command line macro setting to override the default for all ".return" probes.
For ".return" probes, context variables other than the "$return" may be accessible, as a
convenience for a script programmer wishing to access function parameters. These values
are snapshots taken at the time of function entry. (Local variables within the function
are not generally accessible, since those variables did not exist in allocated/initialized
form at the snapshot moment.) These entry-snapshot variables should be accessed via
@entry($var).
In addition, arbitrary entry-time expressions can also be saved for ".return" probes using
the @entry(expr) operator. For example, one can compute the elapsed time of a function:
probe kernel.function("do_filp_open").return {
println( get_timeofday_us() - @entry(get_timeofday_us()) )
}
The following table summarizes how values related to a function parameter context
variable, a pointer named addr, may be accessed from a .return probe.
at-entry value past-exit value
$addr not available
$addr->x->y @cast(@entry($addr),"struct zz")->x->y
$addr[0] {kernel,user}_{char,int,...}(& $addr[0])
DWARFLESS
In absence of debugging information, entry & exit points of kernel & module functions can
be probed using the "kprobe" family of probes. However, these do not permit looking up
the arguments / local variables of the function. Following constructs are supported :
kprobe.function(FUNCTION)
kprobe.function(FUNCTION).call
kprobe.function(FUNCTION).return
kprobe.module(NAME).function(FUNCTION)
kprobe.module(NAME).function(FUNCTION).call
kprobe.module(NAME).function(FUNCTION).return
kprobe.statement(ADDRESS).absolute
Probes of type function are recommended for kernel functions, whereas probes of type
module are recommended for probing functions of the specified module. In case the
absolute address of a kernel or module function is known, statement probes can be
utilized.
Note that FUNCTION and MODULE names must not contain wildcards, or the probe will not be
registered. Also, statement probes must be run under guru-mode only.
USER-SPACE
Support for user-space probing is available for kernels that are configured with the
utrace extensions, or have the uprobes facility in linux 3.5. (Various kernel build
configuration options need to be enabled; systemtap will advise if these are missing.)
There are several forms. First, a non-symbolic probe point:
process(PID).statement(ADDRESS).absolute
is analogous to kernel.statement(ADDRESS).absolute in that both use raw (unverified)
virtual addresses and provide no $variables. The target PID parameter must identify a
running process, and ADDRESS should identify a valid instruction address. All threads of
that process will be probed.
Second, non-symbolic user-kernel interface events handled by utrace may be probed:
process(PID).begin
process("FULLPATH").begin
process.begin
process(PID).thread.begin
process("FULLPATH").thread.begin
process.thread.begin
process(PID).end
process("FULLPATH").end
process.end
process(PID).thread.end
process("FULLPATH").thread.end
process.thread.end
process(PID).syscall
process("FULLPATH").syscall
process.syscall
process(PID).syscall.return
process("FULLPATH").syscall.return
process.syscall.return
process(PID).insn
process("FULLPATH").insn
process(PID).insn.block
process("FULLPATH").insn.block
A process.begin probe gets called when new process described by PID or FULLPATH gets
created. In addition, it is called once from the context of each preexisting process, at
systemtap script startup. This is useful to track live processes. A process.thread.begin
probe gets called when a new thread described by PID or FULLPATH gets created. A
process.end probe gets called when process described by PID or FULLPATH dies. A
process.thread.end probe gets called when a thread described by PID or FULLPATH dies. A
process.syscall probe gets called when a thread described by PID or FULLPATH makes a
system call. The system call number is available in the $syscall context variable, and
the first 6 arguments of the system call are available in the $argN (ex. $arg1, $arg2,
...) context variable. A process.syscall.return probe gets called when a thread described
by PID or FULLPATH returns from a system call. The system call number is available in the
$syscall context variable, and the return value of the system call is available in the
$return context variable. A process.insn probe gets called for every single-stepped
instruction of the process described by PID or FULLPATH. A process.insn.block probe gets
called for every block-stepped instruction of the process described by PID or FULLPATH.
If a process probe is specified without a PID or FULLPATH, all user threads will be
probed. However, if systemtap was invoked with the -c or -x options, then process probes
are restricted to the process hierarchy associated with the target process. If a process
probe is unspecified (i.e. without a PID or FULLPATH), but with the -c option, the PATH of
the -c cmd will be heuristically filled into the process PATH. In that case, only command
parameters are allowed in the -c command (i.e. no command substitution allowed and no
occurrences of any of these characters: '|&;<>(){}').
Third, symbolic static instrumentation compiled into programs and shared libraries may be
probed:
process("PATH").mark("LABEL")
process("PATH").provider("PROVIDER").mark("LABEL")
process(PID).mark("LABEL")
process(PID).provider("PROVIDER").mark("LABEL")
A .mark probe gets called via a static probe which is defined in the application by
STAP_PROBE1(PROVIDER,LABEL,arg1), which are macros defined in sys/sdt.h. The PROVIDER is
an arbitrary application identifier, LABEL is the marker site identifier, and arg1 is the
integer-typed argument. STAP_PROBE1 is used for probes with 1 argument, STAP_PROBE2 is
used for probes with 2 arguments, and so on. The arguments of the probe are available in
the context variables $arg1, $arg2, ... An alternative to using the STAP_PROBE macros is
to use the dtrace script to create custom macros. Additionally, the variables $$name and
$$provider are available as parts of the probe point name. The sys/sdt.h macro names
DTRACE_PROBE* are available as aliases for STAP_PROBE*.
Finally, full symbolic source-level probes in user-space programs and shared libraries are
supported. These are exactly analogous to the symbolic DWARF-based kernel/module probes
described above. They expose the same sorts of context $variables for function
parameters, local variables, and so on.
process("PATH").function("NAME")
process("PATH").statement("*@FILE.c:123")
process("PATH").plt("NAME")
process("PATH").library("PATH").plt("NAME")
process("PATH").library("PATH").function("NAME")
process("PATH").library("PATH").statement("*@FILE.c:123")
process("PATH").function("*").return
process("PATH").function("myfun").label("foo")
process("PATH").function("foo").callee("bar")
process("PATH").plt("NAME").return
process(PID).function("NAME")
process(PID).statement("*@FILE.c:123")
process(PID).plt("NAME")
Note that for all process probes, PATH names refer to executables that are searched the
same way shells do: relative to the working directory if they contain a "/" character,
otherwise in $PATH. If PATH names refer to scripts, the actual interpreters (specified in
the script in the first line after the #! characters) are probed.
Tapset process probes placed in the special directory $prefix/share/systemtap/tapset/PATH/
with relative paths will have their process parameter prefixed with the location of the
tapset. For example,
process("foo").function("NAME")
expands to
process("/usr/bin/foo").function("NAME")
when placed in $prefix/share/systemtap/tapset/PATH/usr/bin/
If PATH is a process component parameter referring to shared libraries then all processes
that map it at runtime would be selected for probing. If PATH is a library component
parameter referring to shared libraries then the process specified by the process
component would be selected. Note that the PATH pattern in a library component will
always apply to libraries statically determined to be in use by the process. However, you
may also specify the full path to any library file even if not statically needed by the
process.
A .plt probe will probe functions in the program linkage table corresponding to the rest
of the probe point. .plt can be specified as a shorthand for .plt("*"). The symbol name
is available as a $$name context variable; function arguments are not available, since
PLTs are processed without debuginfo. A .plt.return probe places a probe at the moment
after the return from the named function.
If the PATH string contains wildcards as in the MPATTERN case, then standard globbing is
performed to find all matching paths. In this case, the $PATH environment variable is not
used.
If systemtap was invoked with the -c or -x options, then process probes are restricted to
the process hierarchy associated with the target process.
JAVA
Support for probing Java methods is available using Byteman as a backend. Byteman is an
instrumentation tool from the JBoss project which systemtap can use to monitor invocations
for a specific method or line in a Java program.
Systemtap does so by generating a Byteman script listing the probes to instrument and then
invoking the Byteman bminstall utility.
This Java instrumentation support is currently a prototype feature with major limitations.
Moreover, Java probing currently does not work across users; the stap script must run
(with appropriate permissions) under the same user that the Java process being probed.
(Thus a stap script under root currently cannot probe Java methods in a non-root-user Java
process.)
The first probe type refers to Java processes by the name of the Java process:
java("PNAME").class("CLASSNAME").method("PATTERN")
java("PNAME").class("CLASSNAME").method("PATTERN").return
The PNAME argument must be a pre-existing jvm pid, and be identifiable via a jps listing.
The PATTERN parameter specifies the signature of the Java method to probe. The signature
must consist of the exact name of the method, followed by a bracketed list of the types of
the arguments, for instance "myMethod(int,double,Foo)". Wildcards are not supported.
The probe can be set to trigger at a specific line within the method by appending a line
number with colon, just as in other types of probes: "myMethod(int,double,Foo):245".
The CLASSNAME parameter identifies the Java class the method belongs to, either with or
without the package qualification. By default, the probe only triggers on descendants of
the class that do not override the method definition of the original class. However,
CLASSNAME can take an optional caret prefix, as in ^org.my.MyClass, which specifies that
the probe should also trigger on all descendants of MyClass that override the original
method. For instance, every method with signature foo(int) in program org.my.MyApp can be
probed at once using
java("org.my.MyApp").class("^java.lang.Object").method("foo(int)")
The second probe type works analogously, but refers to Java processes by PID:
java(PID).class("CLASSNAME").method("PATTERN")
java(PID).class("CLASSNAME").method("PATTERN").return
(PIDs for an already running process can be obtained using the jps(1) utility.)
Context variables defined within java probes include $arg1 through $arg10 (for up to the
first 10 arguments of a method), represented as character-pointers for the toString() form
of each actual argument. The arg1 through arg10 script variables provide access to these
as ordinary strings, fetched via user_string_warn().
Prior to systemtap version 3.1, $arg1 through $arg10 could contain either integers or
character pointers, depending on the types of the objects being passed to each particular
java method. This previous behaviour may be invoked with the stap --compatible=3.0 flag.
PROCFS
These probe points allow procfs "files" in /proc/systemtap/MODNAME to be created, read and
written using a permission that may be modified using the proper umask value. Default
permissions are 0400 for read probes, and 0200 for write probes. If both a read and write
probe are being used on the same file, a default permission of 0600 will be used. Using
procfs.umask(0040).read would result in a 0404 permission set for the file. (MODNAME is
the name of the systemtap module). The proc filesystem is a pseudo-filesystem which is
used as an interface to kernel data structures. There are several probe point variants
supported by the translator:
procfs("PATH").read
procfs("PATH").umask(UMASK).read
procfs("PATH").read.maxsize(MAXSIZE)
procfs("PATH").umask(UMASK).maxsize(MAXSIZE)
procfs("PATH").write
procfs("PATH").umask(UMASK).write
procfs.read
procfs.umask(UMASK).read
procfs.read.maxsize(MAXSIZE)
procfs.umask(UMASK).read.maxsize(MAXSIZE)
procfs.write
procfs.umask(UMASK).write
Note that there are a few differences when procfs probes are used in the stapbpf runtime.
FIFO special files are used instead of proc filesystem files. These files are created in
/var/tmp/systemtap-USER/MODNAME. (USER is the name of the user). Additionally, users
cannot create both read and write probes on the same file.
PATH is the file name (relative to /proc/systemtap/MODNAME or /var/tmp/systemtap-
USER/MODNAME) to be created. If no PATH is specified (as in the last two variants above),
PATH defaults to "command". The file name "__stdin" is used internally by systemtap for
input probes and should not be used as a PATH for procfs probes; see the input probe
section below.
When a user reads /proc/systemtap/MODNAME/PATH (normal runtime) or /var/tmp/systemtap-
USER/MODNAME (stapbpf runtime), the corresponding procfs read probe is triggered. The
string data to be read should be assigned to a variable named $value, like this:
procfs("PATH").read { $value = "100\n" }
When a user writes into /proc/systemtap/MODNAME/PATH (normal runtime) or
/var/tmp/systemtap-USER/MODNAME (stapbpf runtime), the corresponding procfs write probe is
triggered. The data the user wrote is available in the string variable named $value, like
this:
procfs("PATH").write { printf("user wrote: %s", $value) }
MAXSIZE is the size of the procfs read buffer. Specifying MAXSIZE allows larger procfs
output. If no MAXSIZE is specified, the procfs read buffer defaults to STP_PROCFS_BUFSIZE
(which defaults to MAXSTRINGLEN, the maximum length of a string). If setting the procfs
read buffers for more than one file is needed, it may be easiest to override the
STP_PROCFS_BUFSIZE definition. Here's an example of using MAXSIZE:
procfs.read.maxsize(1024) {
$value = "long string..."
$value .= "another long string..."
$value .= "another long string..."
$value .= "another long string..."
}
INPUT
These probe points make input from stdin available to the script during runtime. The
translator currently supports two variants of this family:
input.char
input.line
input.char is triggered each time a character is read from stdin. The current character is
available in the string variable named char. There is no newline buffering; the next
character is read from stdin as soon as it becomes available.
input.line causes all characters read from stdin to be buffered until a newline is read,
at which point the probe will be triggered. The current line of characters (including the
newline) is made available in a string variable named line. Note that no more than
MAXSTRINGLEN characters will be buffered. Any additional characters will not be included
in line.
Input probes are aliases for procfs("__stdin").write. Systemtap reconfigures stdin if the
presence of this procfs probe is detected, therefore "__stdin" should not be used as a
path argument for procfs probes. Additionally, input probes will not work with the -F and
--remote options.
NETFILTER HOOKS
These probe points allow observation of network packets using the netfilter mechanism. A
netfilter probe in systemtap corresponds to a netfilter hook function in the original
netfilter probes API. It is probably more convenient to use tapset::netfilter(3stap),
which wraps the primitive netfilter hooks and does the work of extracting useful
information from the context variables.
There are several probe point variants supported by the translator:
netfilter.hook("HOOKNAME").pf("PROTOCOL_F")
netfilter.pf("PROTOCOL_F").hook("HOOKNAME")
netfilter.hook("HOOKNAME").pf("PROTOCOL_F").priority("PRIORITY")
netfilter.pf("PROTOCOL_F").hook("HOOKNAME").priority("PRIORITY")
PROTOCOL_F is the protocol family to listen for, currently one of NFPROTO_IPV4,
NFPROTO_IPV6, NFPROTO_ARP, or NFPROTO_BRIDGE.
HOOKNAME is the point, or 'hook', in the protocol stack at which to intercept the packet.
The available hook names for each protocol family are taken from the kernel header files
<linux/netfilter_ipv4.h>, <linux/netfilter_ipv6.h>, <linux/netfilter_arp.h> and
<linux/netfilter_bridge.h>. For instance, allowable hook names for NFPROTO_IPV4 are
NF_INET_PRE_ROUTING, NF_INET_LOCAL_IN, NF_INET_FORWARD, NF_INET_LOCAL_OUT, and
NF_INET_POST_ROUTING.
PRIORITY is an integer priority giving the order in which the probe point should be
triggered relative to any other netfilter hook functions which trigger on the same packet.
Hook functions execute on each packet in order from smallest priority number to largest
priority number. If no PRIORITY is specified (as in the first two probe point variants
above), PRIORITY defaults to "0".
There are a number of predefined priority names of the form NF_IP_PRI_* and NF_IP6_PRI_*
which are defined in the kernel header files <linux/netfilter_ipv4.h> and
<linux/netfilter_ipv6.h> respectively. The script is permitted to use these instead of
specifying an integer priority. (The probe points for NFPROTO_ARP and NFPROTO_BRIDGE
currently do not expose any named hook priorities to the script writer.) Thus, allowable
ways to specify the priority include:
priority("255")
priority("NF_IP_PRI_SELINUX_LAST")
A script using guru mode is permitted to specify any identifier or number as the parameter
for hook, pf, and priority. This feature should be used with caution, as the parameter is
inserted verbatim into the C code generated by systemtap.
The netfilter probe points define the following context variables:
$hooknum
The hook number.
$skb The address of the sk_buff struct representing the packet. See <linux/skbuff.h> for
details on how to use this struct, or alternatively use the tapset
tapset::netfilter(3stap) for easy access to key information.
$in The address of the net_device struct representing the network device on which the
packet was received (if any). May be 0 if the device is unknown or undefined at
that stage in the protocol stack.
$out The address of the net_device struct representing the network device on which the
packet will be sent (if any). May be 0 if the device is unknown or undefined at
that stage in the protocol stack.
$verdict
(Guru mode only.) Assigning one of the verdict values defined in
<linux/netfilter.h> to this variable alters the further progress of the packet
through the protocol stack. For instance, the following guru mode script forces all
ipv6 network packets to be dropped:
probe netfilter.pf("NFPROTO_IPV6").hook("NF_IP6_PRE_ROUTING") {
$verdict = 0 /* nf_drop */
}
For convenience, unlike the primitive probe points discussed here, the probes
defined in tapset::netfilter(3stap) export the lowercase names of the verdict
constants (e.g. NF_DROP becomes nf_drop) as local variables.
KERNEL TRACEPOINTS
This family of probe points hooks up to static probing tracepoints inserted into the
kernel or modules. As with markers, these tracepoints are special macro calls inserted by
kernel developers to make probing faster and more reliable than with DWARF-based probes,
and DWARF debugging information is not required to probe tracepoints. Tracepoints have an
extra advantage of more strongly-typed parameters than markers.
Tracepoint probes look like: kernel.trace("name"). The tracepoint name string, which may
contain the usual wildcard characters, is matched against the names defined by the kernel
developers in the tracepoint header files. To restrict the search to specific subsystems
(e.g. sched, ext3, etc...), the following syntax can be used: kernel.trace("system:name").
The tracepoint system string may also contain the usual wildcard characters.
The handler associated with a tracepoint-based probe may read the optional parameters
specified at the macro call site. These are named according to the declaration by the
tracepoint author. For example, the tracepoint probe kernel.trace("sched:sched_switch")
provides the parameters $prev and $next. If the parameter is a complex type, as in a
struct pointer, then a script can access fields with the same syntax as DWARF $target
variables. Also, tracepoint parameters cannot be modified, but in guru-mode a script may
modify fields of parameters.
The subsystem and name of the tracepoint are available in $$system and $$name and a string
of name=value pairs for all parameters of the tracepoint is available in $$vars or
$$parms.
KERNEL MARKERS (OBSOLETE)
This family of probe points hooks up to an older style of static probing markers inserted
into older kernels or modules. These markers are special STAP_MARK macro calls inserted
by kernel developers to make probing faster and more reliable than with DWARF-based
probes. Further, DWARF debugging information is not required to probe markers.
Marker probe points begin with kernel. The next part names the marker itself:
mark("name"). The marker name string, which may contain the usual wildcard characters, is
matched against the names given to the marker macros when the kernel and/or module was
compiled. Optionally, you can specify format("format"). Specifying the marker format
string allows differentiation between two markers with the same name but different marker
format strings.
The handler associated with a marker-based probe may read the optional parameters
specified at the macro call site. These are named $arg1 through $argNN, where NN is the
number of parameters supplied by the macro. Number and string parameters are passed in a
type-safe manner.
The marker format string associated with a marker is available in $format. And also the
marker name string is available in $name.
HARDWARE BREAKPOINTS
This family of probes is used to set hardware watchpoints for a given
(global) kernel symbol. The probes take three components as inputs :
1. The virtual address / name of the kernel symbol to be traced is supplied as argument to
this class of probes. ( Probes for only data segment variables are supported. Probing
local variables of a function cannot be done.)
2. Nature of access to be probed : a. .write probe gets triggered when a write happens at
the specified address/symbol name. b. rw probe is triggered when either a read or write
happens.
3. .length (optional) Users have the option of specifying the address interval to be
probed using "length" constructs. The user-specified length gets approximated to the
closest possible address length that the architecture can support. If the specified length
exceeds the limits imposed by architecture, an error message is flagged and probe
registration fails. Wherever 'length' is not specified, the translator requests a
hardware breakpoint probe of length 1. It should be noted that the "length" construct is
not valid with symbol names.
Following constructs are supported :
probe kernel.data(ADDRESS).write
probe kernel.data(ADDRESS).rw
probe kernel.data(ADDRESS).length(LEN).write
probe kernel.data(ADDRESS).length(LEN).rw
probe kernel.data("SYMBOL_NAME").write
probe kernel.data("SYMBOL_NAME").rw
This set of probes make use of the debug registers of the processor, which is a scarce
resource. (4 on x86 , 1 on powerpc ) The script translation flags a warning if a user
requests more hardware breakpoint probes than the limits set by architecture. For
example,a pass-2 warning is flashed when an input script requests 5 hardware breakpoint
probes on an x86 system while x86 architecture supports a maximum of 4 breakpoints. Users
are cautioned to set probes judiciously.
PERF
This family of probe points interfaces to the kernel "perf event" infrastructure for
controlling hardware performance counters. The events being attached to are described by
the "type", "config" fields of the perf_event_attr structure, and are sampled at an
interval governed by the "sample_period" and "sample_freq" fields.
These fields are made available to systemtap scripts using the following syntax:
probe perf.type(NN).config(MM).sample(XX)
probe perf.type(NN).config(MM).hz(XX)
probe perf.type(NN).config(MM)
probe perf.type(NN).config(MM).process("PROC")
probe perf.type(NN).config(MM).counter("COUNTER")
probe perf.type(NN).config(MM).process("PROC").counter("NAME")
The systemtap probe handler is called once per XX increments of the underlying performance
counter when using the .sample field or at a frequency in hertz when using the .hz field.
When not specified, the default behavior is to sample at a count of 1000000. The range of
valid type/config is described by the perf_event_open(2) system call, and/or the
linux/perf_event.h file. Invalid combinations or exhausted hardware counter resources
result in errors during systemtap script startup. Systemtap does not sanity-check the
values: it merely passes them through to the kernel for error- and safety-checking. By
default the perf event probe is systemwide unless .process is specified, which will bind
the probe to a specific task. If the name is omitted then it is inferred from the stap -c
argument. A perf event can be read on demand using .counter. The body of the perf probe
handler will not be invoked for a .counter probe; instead, the counter is read in a user
space probe via:
process("PROC").statement("func@file") {stat <<< @perf("NAME")}
PYTHON
Support for probing python 2 and python 3 function is available with the help of an extra
python support module. Note that the debuginfo for the version of python being probed is
required. To run a python script with the extra python support module you'd add the '-m
HelperSDT' option to your python command, like this:
stap foo.stp -c "python -m HelperSDT foo.py"
Python probes look like the following:
python2.module("MPATTERN").function("PATTERN")
python2.module("MPATTERN").function("PATTERN").call
python2.module("MPATTERN").function("PATTERN").return
python3.module("MPATTERN").function("PATTERN")
python3.module("MPATTERN").function("PATTERN").call
python3.module("MPATTERN").function("PATTERN").return
The list above includes multiple variants and modifiers which provide additional
functionality or filters. They are:
.function
Places a probe at the beginning of the named function by default, unless
modified by PATTERN. Parameters are available as context variables.
.call Places a probe at the beginning of the named function. Parameters are
available as context variables.
.return
Places a probe at the moment before the return from the named function.
Parameters and local/global python variables are available as context
variables.
PATTERN stands for a string literal that aims to identify a point in the python program.
It is made up of three parts:
• The first part is the name of a function (e.g. "foo") or class method (e.g.
"bar.baz"). This part may use the "*" and "?" wildcarding operators to match multiple
names.
• The second part is optional and begins with the "@" character. It is followed by the
path to the source file containing the function, which may include a wildcard pattern.
The python path is searched for a matching filename.
• Finally, the third part is optional if the file name part was given, and identifies
the line number in the source file preceded by a ":" or a "+". The line number is
assumed to be an absolute line number if preceded by a ":", or relative to the
declaration line of the function if preceded by a "+". All the lines in the function
can be matched with ":*". A range of lines x through y can be matched with ":x-y".
Ranges and specific lines can be mixed using commas, e.g. ":x,y-z".
In the above list of probe points, MPATTERN stands for a python module or script name that
names the python module of interest. This part may use the "*" and "?" wildcarding
operators to match multiple names. The python path is searched for a matching filename.
EXAMPLES
Here are some example probe points, defining the associated events.
begin, end, end
refers to the startup and normal shutdown of the session. In this case, the
handler would run once during startup and twice during shutdown.
timer.jiffies(1000).randomize(200)
refers to a periodic interrupt, every 1000 +/- 200 jiffies.
kernel.function("*init*"), kernel.function("*exit*")
refers to all kernel functions with "init" or "exit" in the name.
kernel.function("*@kernel/time.c:240")
refers to any functions within the "kernel/time.c" file that span line 240. Note
that this is not a probe at the statement at that line number. Use the
kernel.statement probe instead.
kernel.trace("sched_*")
refers to all scheduler-related (really, prefixed) tracepoints in the kernel.
kernel.mark("getuid")
refers to an obsolete STAP_MARK(getuid, ...) macro call in the kernel.
module("usb*").function("*sync*").return
refers to the moment of return from all functions with "sync" in the name in any of
the USB drivers.
kernel.statement(0xc0044852)
refers to the first byte of the statement whose compiled instructions include the
given address in the kernel.
kernel.statement("*@kernel/time.c:296")
refers to the statement of line 296 within "kernel/time.c".
kernel.statement("bio_init@fs/bio.c+3")
refers to the statement at line bio_init+3 within "fs/bio.c".
kernel.data("pid_max").write
refers to a hardware breakpoint of type "write" set on pid_max
syscall.*.return
refers to the group of probe aliases with any name in the third position
SEE ALSO
stap(1),
probe::*(3stap),
tapset::*(3stap)
STAPPROBES(3stap)