Ubuntu Manpage: sg_compare_and_write - send the SCSI COMPARE AND WRITE command

Provided by: sg3-utils_1.46-1build1_amd64

NAME

       sg_compare_and_write - send the SCSI COMPARE AND WRITE command

SYNOPSIS

       sg_compare_and_write  [--dpo] [--fua] [--fua_nv] [--grpnum=GN] [--help] --in=IF [--inw=WF]
       --lba=LBA [--num=NUM] [--quiet] [--timeout=TO]  [--verbose]  [--version]  [--wrprotect=WP]
       [--xferlen=LEN] DEVICE

DESCRIPTION

Send the SCSI COMPARE AND WRITE command to DEVICE. This utility fetches a compare buffer
and a write buffer from either one or two files. If the --inw=WF option is given then the
compare buffer is fetched from the file indicated by the --in=IF while the write buffer is
fetched from the file indicated by the --inw=WF. If the --inw=WF option is not given then
the concatenated compare and write buffers are fetched from the file indicated by the
--in=IF option.

Those buffers are expected to each contain NUM blocks of data. The compare starts at
logical block address LBA on the DEVICE and if the comparison fails (i.e. the provided
compare buffer does not equal the data at LBA on the DEVICE) then the COMPARE AND WRITE
command finishes with a sense key of MISCOMPARE. In this case this utility will complete
and set an exit status of 14 (which happens to be the sense key value of MISCOMPARE).

If the comparison succeeds then the provided write buffer is stored starting at LBA for
NUM blocks on the DEVICE.

The actual number of bytes transferred in the data-out buffer of the COMPARE AND WRITE
command may need to be given by the user with the --xferlen=LEN option. LEN defaults to (2
* NUM * 512) which is 1024 for the default NUM of 1. If the block size is other than 512
then the user will need to use --xferlen=LEN option. If protection information is given
(indicated by a value of WP other than 0 (the default)) then for a NUM of 1 LEN should be
1040 . Note that the SCSI READ CAPACITY command is not performed by this utility (e.g. to
find the block size).

The T10 definition of the SCSI COMPARE AND WRITE command requires that the DEVICE
implement the compare and optional write as an uninterrupted series of actions. Depending
on some other DEVICE settings a verify operation may occur prior to the compare.

When a mismatch occurs between the compare buffer and the blocks starting at LBA read from
the DEVICE the sense buffer containing the MISCOMPARE sense key causes several messages to
be sent to stderr (including the offset of the first byte mismatch). To suppress these
messages use the --quiet option. With or without the --quiet option the exit status will
be set to 14.

This command is defined in SBC-3 whose most recent revision is 36. SBC-3 and other SCSI
documents can be found at http://www.t10.org .

OPTIONS

Arguments to long options are mandatory for short options as well. The options are
arranged in alphabetical order based on the long option name.

-d, --dpo
Set the DPO bit in the COMPARE AND WRITE CDB

-f, --fua
Set the FUA bit in the COMPARE AND WRITE CDB

-F, --fua_nv
Set the FUA_NV bit in the COMPARE AND WRITE CDB. This bit was removed in SBC-3
revision 35d and its position marked as "reserved".

-g, --grpnum=GN
where GN is the value to be placed in the group number field in the COMPARE AND
WRITE CDB.

-h, --help
output the usage message then exit.

-i, --in=IF
read data (binary) from file named IF. This will either be the combined compare and
write buffers (when the --inw=WF option is not given) or just the compare buffer
(when the --inw=WF option is given). If IF is '-' then stdin (e.g. a pipe) is read.

-C, --inc=IF
The same as the --in option.

-D, --inw=WF
read data (binary) from file named WF. This will the write buffer that will become
the second half of the data-out buffer sent to the DEVICE associated with the
COMPARE AND WRITE command. Note that when this option is given then the --in=IF is
expected to hold the associated compare buffer.

-l, --lba=LBA
where LBA is the logical block address to start the COMPARE AND WRITE command.
Assumed to be in decimal unless prefixed with '0x' or has a trailing 'h'.

-n, --num=NUM
where NUM is the number of blocks, starting at LBA, to read and compare with the
verify instance. And given a match, the NUM of blocks to write starting LBA. The
default value for NUM is 1.

-q, --quiet
suppress the sense buffer messages associated with a MISCOMPARE sense key that
would otherwise be sent to stderr. Still set the exit status to 14 which is the
sense key value indicating a MISCOMPARE.

-t, --timeout=TO
where TO is the command timeout value in seconds. The default value is 60 seconds.
If NUM is large (or zero) a WRITE SAME command may require considerably more time
than 60 seconds to complete.

-v, --verbose
increase the degree of verbosity (debug messages).

-V, --version
output version string then exit.

-w, --wrprotect=WP
set the WRPROTECT field in the cdb to WP. The default value is 0 which implies no
protection information is sent (along with the user data) by this utility.

-x, --xferlen=LEN
where LEN is the data out buffer length in byte. It defaults to (2 * NUM * 512)
bytes. If the DEVICE block size is other than 512 bytes or WP is non-zero (implying
additional protection information) then this default will be incorrect; the use
must supply the correct value for LEN

NOTES

       Various  numeric  arguments  (e.g. LBA) may include multiplicative suffixes or be given in
       hexadecimal. See the "NUMERIC ARGUMENTS" section in the sg3_utils(8) man page.

EXAMPLES

       Before overwriting the first two blocks of whatever (SCSI) storage device that is  chosen,
       take  a  small  backup. The logical block size is assumed to be 512 bytes. Take a copy (in
       backup01.bin) of the first two blocks::

         # sg_dd if=/dev/sg1 bs=512 of=backup01.bin count=2
         2+0 records in
         2+0 records out

       WARNING: if /dev/sg1 corresponds to a disk on your system that contains currently  mounted
       file  systems,  do  _not_  continue. If you can, unmount all file systems on that disk. If
       that is not possible, use another disk with no mounted file systems on it.  In  Linux  the
       scsi_debug driver is a good candidate for experimentation.

       Now fill the first block with 0xff bytes:

         # sg_dd iflag=ff bs=512 of=/dev/sg1 count=1
         1+0 records in
         1+0 records out

       and the second block with 0x0 bytes:

         # sg_dd iflag=00 bs=512 seek=1 of=/dev/sg1 count=1
         1+0 records in
         1+0 records out

       Now copy those two blocks into a file:

         # sg_dd if=/dev/sg1 bs=512 of=ff00.bin count=2
         2+0 records in
         2+0 records out

       Now we can do a compare and write command. It is told to compare the first block (i.e. LBA
       0) with the first block in the given file (i.e. ff00.bin).  If they are equal (they should
       be both full of 0xff bytes). Since the compare succeeds, it will write the second block in
       ff00.bin over LBA 0:

         # sg_compare_and_write --in=ff00.bin --lba=0 --num=1 /dev/sg1

       No news is good news. Now if we do that command again:

         # sg_compare_and_write --in=ff00.bin --lba=0 --num=1 /dev/sg1
         Miscompare at byte offset: 0 [0x0]
         sg_compare_and_write failed: Miscompare

       This is expected. The first sg_compare_and_write ended up writing 0x0 bytes over LBA  0x0.
       The  second  sg_compare_and_write  command  compares  LBA  0x0  with  0xff bytes and fails
       immediately (i.e. at byte offset: 0). Now we will overwrite the first 3 bytes of  ff00.bin
       with 0x0:

         # sg_dd bs=1 iflag=00 of=ff00.bin count=3
         3+0 records in
         3+0 records out

       Notice  the 'bs=1' operand. The dd utility (and thus sg_dd) is very useful for doing small
       binary edits on a file. Now if we do that sg_compare_and_write again, it still  fails  but
       with a small difference:

         # sg_compare_and_write --in=ff00.bin --lba=0 --num=1 /dev/sg1
         Miscompare at byte offset: 3 [0x3]
         sg_compare_and_write failed: Miscompare

       So  the  bytes at offset 0, 1, and 2 compared equal but not the byte at offset 3. The SCSI
       COMPARE AND WRITE will stop on the first micompared byte.

EXIT STATUS

       The exit status of sg_compare_and_write is 0 when it is successful. If  the  compare  step
       fails then the exit status is 14. For other exit status values see the EXIT STATUS section
       in the sg3_utils(8) man page.

       Earlier versions of this utility set an exit status of 98 when there was a MISCOMPARE.

AUTHORS

       Written by Shahar Salzman. Maintained by Douglas Gilbert. Additions by Eric Seppanen.

REPORTING BUGS

       Report bugs to shahar.salzman@kaminario.com or dgilbert@interlog.com

COPYRIGHT

       Copyright © 2012-2020 Kaminario Technologies LTD
       Redistribution and use in source and binary  forms,  with  or  without  modification,  are
       permitted provided that the following conditions are met:
       *  Redistributions  of  source  code  must retain the above copyright notice, this list of
       conditions and the following disclaimer.
       * Redistributions in binary form must reproduce the above copyright notice, this  list  of
       conditions  and  the  following  disclaimer  in  the  documentation and/or other materials
       provided with the distribution.
       * Neither the name of the <organization> nor the names of its contributors may be used  to
       endorse  or  promote  products  derived  from this software without specific prior written
       permission.

       THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT  HOLDERS  AND  CONTRIBUTORS  "AS  IS"  AND  ANY
       EXPRESS  OR  IMPLIED  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
       MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN  NO  EVENT  SHALL
       Kaminario  Technologies  LTD  BE  LIABLE  FOR  ANY  DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
       EXEMPLARY, OR CONSEQUENTIAL  DAMAGES  (INCLUDING,  BUT  NOT  LIMITED  TO,  PROCUREMENT  OF
       SUBSTITUTE  GOODS  OR  SERVICES;  LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
       HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT  LIABILITY,  OR
       TORT  (INCLUDING  NEGLIGENCE  OR  OTHERWISE)  ARISING  IN  ANY  WAY OUT OF THE USE OF THIS
       SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.