NAME

       cryptsetup-repair - repair the device metadata

SYNOPSIS

       cryptsetup repair [<options>] <device>

DESCRIPTION

       Tries to repair the device metadata if possible. Currently supported only for LUKS device
       type.

       This command is useful to fix some known benign LUKS metadata header corruptions. Only
       basic corruptions of unused keyslot are fixable. This command will only change the LUKS
       header, not any key-slot data. You may enforce LUKS version by adding --type option.

       It also repairs (upgrades) LUKS2 reencryption metadata by adding a metadata digest that
       protects it against malicious changes.

       If LUKS2 reencryption was interrupted in the middle of writing reencryption segment the
       repair command can be used to perform reencryption recovery so that reencryption can
       continue later. Repairing reencryption requires verification of reencryption keyslot so
       passphrase or keyfile is needed.

       <options> can be [--timeout, --verify-passphrase, --disable-locks, --type, --header,
       --key-file, --keyfile-size, --keyfile-offset, --key-slot].

       WARNING: Always create a binary backup of the original header before calling this command.

OPTIONS

       --type <device-type>
           Specifies required device type, for more info read BASIC ACTIONS section in
           cryptsetup(8).

       --verify-passphrase, -y
           When interactively asking for a passphrase, ask for it twice and complain if both
           inputs do not match. Ignored on input from file or stdin.

       --key-file, -d name
           Read the passphrase from file.

           If the name given is "-", then the passphrase will be read from stdin. In this case,
           reading will not stop at newline characters.

           See section NOTES ON PASSPHRASE PROCESSING in cryptsetup(8) for more information.

       --keyfile-offset value
           Skip value bytes at the beginning of the key file.

       --keyfile-size, -l value
           Read a maximum of value bytes from the key file. The default is to read the whole file
           up to the compiled-in maximum that can be queried with --help. Supplying more data
           than the compiled-in maximum aborts the operation.

           This option is useful to cut trailing newlines, for example. If --keyfile-offset is
           also given, the size count starts after the offset.

       --key-slot, -S <0-N>
           For LUKS operations that add key material, this option allows you to specify which key
           slot is selected for the new key.

           The maximum number of key slots depends on the LUKS version. LUKS1 can have up to 8
           key slots. LUKS2 can have up to 32 key slots based on key slot area size and key size,
           but a valid key slot ID can always be between 0 and 31 for LUKS2.

       --timeout, -t <number of seconds>
           The number of seconds to wait before timeout on passphrase input via terminal. It is
           relevant every time a passphrase is asked. It has no effect if used in conjunction
           with --key-file.

           This option is useful when the system should not stall if the user does not input a
           passphrase, e.g. during boot. The default is a value of 0 seconds, which means to wait
           forever.

       --header <device or file storing the LUKS header>
           Use a detached (separated) metadata device or file where the LUKS header is stored.
           This option allows one to store ciphertext and LUKS header on different devices.

           For commands that change the LUKS header (e.g. luksAddKey), specify the device or file
           with the LUKS header directly as the LUKS device.

       --disable-locks
           Disable lock protection for metadata on disk. This option is valid only for LUKS2 and
           ignored for other formats.

           WARNING: Do not use this option unless you run cryptsetup in a restricted environment
           where locking is impossible to perform (where /run directory cannot be used).

       --batch-mode, -q
           Suppresses all confirmation questions. Use with care!

           If the --verify-passphrase option is not specified, this option also switches off the
           passphrase verification.

       --debug or --debug-json
           Run in debug mode with full diagnostic logs. Debug output lines are always prefixed by
           #.

           If --debug-json is used, additional LUKS2 JSON data structures are printed.

       --version, -V
           Show the program version.

       --usage
           Show short option help.

       --help, -?
           Show help text and default parameters.

REPORTING BUGS

       Report bugs at cryptsetup mailing list <cryptsetup@lists.linux.dev> or in Issues project
       section <https://gitlab.com/cryptsetup/cryptsetup/-/issues/new>.

       Please attach output of the failed command with --debug option added.

SEE ALSO

       Cryptsetup FAQ <https://gitlab.com/cryptsetup/cryptsetup/wikis/FrequentlyAskedQuestions>

       cryptsetup(8), integritysetup(8) and veritysetup(8)

CRYPTSETUP

       Part of cryptsetup project <https://gitlab.com/cryptsetup/cryptsetup/>.