Provided by: util-linux_2.38.1-4ubuntu1_amd64 
NAME
rtcwake - enter a system sleep state until specified wakeup time
SYNOPSIS
rtcwake [options] [-d device] [-m standby_mode] {-s seconds|-t time_t}
DESCRIPTION
This program is used to enter a system sleep state and to automatically wake from it at a
specified time.
This uses cross-platform Linux interfaces to enter a system sleep state, and leave it no
later than a specified time. It uses any RTC framework driver that supports standard
driver model wakeup flags.
This is normally used like the old apmsleep utility, to wake from a suspend state like
ACPI S1 (standby) or S3 (suspend-to-RAM). Most platforms can implement those without
analogues of BIOS, APM, or ACPI.
On some systems, this can also be used like nvram-wakeup, waking from states like ACPI S4
(suspend to disk). Not all systems have persistent media that are appropriate for such
suspend modes.
Note that alarm functionality depends on hardware; not every RTC is able to setup an alarm
up to 24 hours in the future.
The suspend setup may be interrupted by active hardware; for example wireless USB input
devices that continue to send events for some fraction of a second after the return key is
pressed. rtcwake tries to avoid this problem and it waits to the terminal to settle down
before entering a system sleep.
OPTIONS
-A, --adjfile file
Specify an alternative path to the adjust file.
-a, --auto
Read the clock mode (whether the hardware clock is set to UTC or local time) from the
adjtime file, where hwclock(8) stores that information. This is the default.
--date timestamp
Set the wakeup time to the value of the timestamp. Format of the timestamp can be any
of the following:
┌────────────────────┬────────────────────────────────┐
│ │ │
│YYYYMMDDhhmmss │ │
├────────────────────┼────────────────────────────────┤
│ │ │
│YYYY-MM-DD hh:mm:ss │ │
├────────────────────┼────────────────────────────────┤
│ │ │
│YYYY-MM-DD hh:mm │ (seconds will be set to 00) │
├────────────────────┼────────────────────────────────┤
│ │ │
│YYYY-MM-DD │ (time will be set to 00:00:00) │
├────────────────────┼────────────────────────────────┤
│ │ │
│hh:mm:ss │ (date will be set to today) │
├────────────────────┼────────────────────────────────┤
│ │ │
│hh:mm │ (date will be set to today, │
│ │ seconds to 00) │
├────────────────────┼────────────────────────────────┤
│ │ │
│tomorrow │ (time is set to 00:00:00) │
├────────────────────┼────────────────────────────────┤
│ │ │
│+5min │ │
└────────────────────┴────────────────────────────────┘
-d, --device device
Use the specified device instead of rtc0 as realtime clock. This option is only
relevant if your system has more than one RTC. You may specify rtc1, rtc2, ... here.
-l, --local
Assume that the hardware clock is set to local time, regardless of the contents of the
adjtime file.
--list-modes
List available --mode option arguments.
-m, --mode mode
Go into the given standby state. Valid values for mode are:
standby
ACPI state S1. This state offers minimal, though real, power savings, while
providing a very low-latency transition back to a working system. This is the
default mode.
freeze
The processes are frozen, all the devices are suspended and all the processors
idled. This state is a general state that does not need any platform-specific
support, but it saves less power than Suspend-to-RAM, because the system is still
in a running state. (Available since Linux 3.9.)
mem
ACPI state S3 (Suspend-to-RAM). This state offers significant power savings as
everything in the system is put into a low-power state, except for memory, which
is placed in self-refresh mode to retain its contents.
disk
ACPI state S4 (Suspend-to-disk). This state offers the greatest power savings, and
can be used even in the absence of low-level platform support for power
management. This state operates similarly to Suspend-to-RAM, but includes a final
step of writing memory contents to disk.
off
ACPI state S5 (Poweroff). This is done by calling '/sbin/shutdown'. Not officially
supported by ACPI, but it usually works.
no
Don’t suspend, only set the RTC wakeup time.
on
Don’t suspend, but read the RTC device until an alarm time appears. This mode is
useful for debugging.
disable
Disable a previously set alarm.
show
Print alarm information in format: "alarm: off|on <time>". The time is in ctime()
output format, e.g., "alarm: on Tue Nov 16 04:48:45 2010".
-n, --dry-run
This option does everything apart from actually setting up the alarm, suspending the
system, or waiting for the alarm.
-s, --seconds seconds
Set the wakeup time to seconds in the future from now.
-t, --time time_t
Set the wakeup time to the absolute time time_t. time_t is the time in seconds since
1970-01-01, 00:00 UTC. Use the date(1) tool to convert between human-readable time and
time_t.
-u, --utc
Assume that the hardware clock is set to UTC (Universal Time Coordinated), regardless
of the contents of the adjtime file.
-v, --verbose
Be verbose.
-h, --help
Display help text and exit.
-V, --version
Print version and exit.
NOTES
Some PC systems can’t currently exit sleep states such as mem using only the kernel code
accessed by this driver. They need help from userspace code to make the framebuffer work
again.
FILES
/etc/adjtime
HISTORY
The program was posted several times on LKML and other lists before appearing in kernel
commit message for Linux 2.6 in the GIT commit 87ac84f42a7a580d0dd72ae31d6a5eb4bfe04c6d.
AUTHORS
The program was written by David Brownell <dbrownell@users.sourceforge.net> and improved
by Bernhard Walle <bwalle@suse.de>.
COPYRIGHT
This is free software. You may redistribute copies of it under the terms of the GNU
General Public License <http://www.gnu.org/licenses/gpl.html>. There is NO WARRANTY, to
the extent permitted by law.
SEE ALSO
adjtime_config(5), hwclock(8), date(1)
REPORTING BUGS
For bug reports, use the issue tracker at https://github.com/util-linux/util-linux/issues.
AVAILABILITY
The rtcwake command is part of the util-linux package which can be downloaded from Linux
Kernel Archive <https://www.kernel.org/pub/linux/utils/util-linux/>.