Provided by: corosync_3.1.7-1ubuntu1_amd64 
NAME
corosync.conf - corosync executive configuration file
SYNOPSIS
/etc/corosync/corosync.conf
DESCRIPTION
The corosync.conf instructs the corosync executive about various parameters needed to
control the corosync executive. Empty lines and lines starting with # character are
ignored. The configuration file consists of bracketed top level directives. The possible
directive choices are:
totem { }
This top level directive contains configuration options for the totem protocol.
logging { }
This top level directive contains configuration options for logging.
quorum { }
This top level directive contains configuration options for quorum.
nodelist { }
This top level directive contains configuration options for nodes in cluster.
system { }
This top level directive contains configuration options related to system.
resources { }
This top level directive contains configuration options for resources.
nozzle { }
This top level directive contains configuration options for a libnozzle device.
The interface sub-directive of totem is optional for UDP and knet transports.
For knet, multiple interface subsections define parameters for each knet link on the
system.
For UDPU an interface section is not needed and it is recommended that the nodelist is
used to define cluster nodes.
linknumber
This specifies the link number for the interface. When using the knet protocol,
each interface should specify separate link numbers to uniquely identify to the
membership protocol which interface to use for which link. The linknumber must
start at 0. For UDP the only supported linknumber is 0.
knet_link_priority
This specifies the priority for the link when knet is used in 'passive' mode. (see
link_mode below)
knet_ping_interval
This specifies the interval between knet link pings. knet_ping_interval and
knet_ping_timeout are a pair, if one is specified the other should be too,
otherwise one will be calculated from the token timeout and one will be taken from
the config file. (default is token timeout / (knet_pong_count*2))
knet_ping_timeout
If no ping is received within this time, the knet link is declared dead.
knet_ping_interval and knet_ping_timeout are a pair, if one is specified the other
should be too, otherwise one will be calculated from the token timeout and one will
be taken from the config file. (default is token timeout / knet_pong_count)
knet_ping_precision
How many values of latency are used to calculate the average link latency. (default
2048 samples)
knet_pong_count
How many valid ping/pongs before a link is marked UP. (default 2)
knet_transport
Which IP transport knet should use. valid values are "sctp" or "udp". (default:
udp)
bindnetaddr (udp only)
This specifies the network address the corosync executive should bind to when using
udp.
bindnetaddr (udp only) should be an IP address configured on the system, or a
network address.
For example, if the local interface is 192.168.5.92 with netmask 255.255.255.0, you
should set bindnetaddr to 192.168.5.92 or 192.168.5.0. If the local interface is
192.168.5.92 with netmask 255.255.255.192, set bindnetaddr to 192.168.5.92 or
192.168.5.64, and so forth.
This may also be an IPV6 address, in which case IPV6 networking will be used. In
this case, the exact address must be specified and there is no automatic selection
of the network interface within a specific subnet as with IPv4.
If IPv6 networking is used, the nodeid field in nodelist must be specified.
broadcast (udp only)
This is optional and can be set to yes. If it is set to yes, the broadcast address
will be used for communication. If this option is set, mcastaddr should not be
set.
mcastaddr (udp only)
This is the multicast address used by corosync executive. The default should work
for most networks, but the network administrator should be queried about a
multicast address to use. Avoid 224.x.x.x because this is a "config" multicast
address.
This may also be an IPV6 multicast address, in which case IPV6 networking will be
used. If IPv6 networking is used, the nodeid field in nodelist must be specified.
It's not necessary to use this option if cluster_name option is used. If both
options are used, mcastaddr has higher priority.
mcastport (udp only)
This specifies the UDP port number. It is possible to use the same multicast
address on a network with the corosync services configured for different UDP ports.
Please note corosync uses two UDP ports mcastport (for mcast receives) and
mcastport - 1 (for mcast sends). If you have multiple clusters on the same network
using the same mcastaddr please configure the mcastports with a gap.
ttl (udp only)
This specifies the Time To Live (TTL). If you run your cluster on a routed network
then the default of "1" will be too small. This option provides a way to increase
this up to 255. The valid range is 0..255.
Within the totem directive, there are seven configuration options of which one is
required, five are optional, and one is required when IPV6 is configured in the interface
subdirective. The required directive controls the version of the totem configuration.
The optional option unless using IPV6 directive controls identification of the processor.
The optional options control secrecy and authentication, the network mode of operation and
maximum network MTU field.
version
This specifies the version of the configuration file. Currently the only valid
version for this directive is 2.
clear_node_high_bit
This configuration option is optional and is only relevant when no nodeid is
specified. Some corosync clients require a signed 32 bit nodeid that is greater
than zero however by default corosync uses all 32 bits of the IPv4 address space
when generating a nodeid. Set this option to yes to force the high bit to be zero
and therefore ensure the nodeid is a positive signed 32 bit integer.
WARNING: Cluster behavior is undefined if this option is enabled on only a subset
of the cluster (for example during a rolling upgrade).
crypto_model
This specifies which cryptographic library should be used by knet. Supported
values depend on the libknet build and on the installed cryptography libraries.
Typically nss and openssl will be available but gcrypt and others could also be
allowed.
The default is nss.
crypto_hash
This specifies which HMAC authentication should be used to authenticate all
messages. Valid values are none (no authentication), md5, sha1, sha256, sha384 and
sha512. Encrypted transmission is only supported for the knet transport.
The default is none.
crypto_cipher
This specifies which cipher should be used to encrypt all messages. Valid values
are none (no encryption), aes256, aes192 and aes128. Enabling crypto_cipher,
requires also enabling of crypto_hash. Encrypted transmission is only supported for
the knet transport.
The default is none.
secauth
This implies crypto_cipher=aes256 and crypto_hash=sha256, unless those options are
explicitly set. Encrypted transmission is only supported for the knet transport.
The default is off.
keyfile
This specifies the fully qualified path to the shared key used to authenticate and
encrypt data used within the Totem protocol.
The default is /etc/corosync/authkey.
key Shared key stored in configuration instead of authkey file. This option has lower
precedence than keyfile option so it's used only when keyfile is not specified.
Using this option is not recommended for security reasons.
link_mode
This specifies the Kronosnet mode, which may be passive, active, or rr (round-
robin). passive: the active link with the highest priority (highest number) will
be used. If one or more links share the same priority the one with the lowest link
ID will be used. active: All active links will be used simultaneously to send
traffic. link priority is ignored. rr: Round-Robin policy. Each packet will be
sent to the next active link in order.
If only one interface directive is specified, passive is automatically chosen.
The maximum number of interface directives that is allowed with Kronosnet is 8. For
other transports it is 1.
netmtu This specifies maximum packet length sent by corosync. It's mainly for the UDPU
(and UDP) transport, where it specifies the network maximum transmit size, but can
be used also with the KNET transport, where it defines the maximum length of
packets passed to the knet layer. To specify the network MTU manually for KNET, use
the knet_mtu option.
For UDPU (and UDP), setting this value beyond 1500, the regular frame MTU, requires
ethernet devices that support large, or also called jumbo, frames. If any device
in the network doesn't support large frames, the protocol will not operate
properly. The hosts must also have their mtu size set from 1500 to whatever frame
size is specified here.
Please note while some NICs or switches claim large frame support, they support
9000 MTU as the maximum frame size including the IP header. Setting the netmtu and
host MTUs to 9000 will cause totem to use the full 9000 bytes of the frame. Then
Linux will add a 18 byte header moving the full frame size to 9018. As a result
some hardware will not operate properly with this size of data. A netmtu of 8982
seems to work for the few large frame devices that have been tested. Some
manufacturers claim large frame support when in fact they support frame sizes of
4500 bytes.
When sending multicast traffic, if the network frequently reconfigures, chances are
that some device in the network doesn't support large frames.
Choose hardware carefully if intending to use large frame support.
The default is 1500 for UDPU (and UDP) and 65536 for the KNET transport.
transport
This directive controls the transport mechanism used. The default is knet. The
transport type can also be set to udpu or udp. Only knet allows crypto or multiple
interfaces per node.
cluster_name
This specifies the name of cluster and it's used for automatic generating of
multicast address.
config_version
This specifies version of config file. This is converted to unsigned 64-bit int.
By default it's 0. Option is used to prevent joining old nodes with not up-to-date
configuration. If value is not 0, and node is going for first time (only for first
time, join after split doesn't follow this rules) from single-node membership to
multiple nodes membership, other nodes config_versions are collected. If current
node config_version is not equal to highest of collected versions, corosync is
terminated.
ip_version
This specifies version of IP to ask DNS resolver for. The value can be one of ipv4
(look only for an IPv4 address) , ipv6 (check only IPv6 address) , ipv4-6 (look for
all address families and use first IPv4 address found in the list if there is such
address, otherwise use first IPv6 address) and ipv6-4 (look for all address
families and use first IPv6 address found in the list if there is such address,
otherwise use first IPv4 address).
Default (if unspecified) is ipv6-4 for knet and udpu transports and ipv4 for udp.
The knet transport supports IPv4 and IPv6 addresses concurrently, provided they are
consistent on each link.
Within the totem directive, there are several configuration options which are used
to control the operation of the protocol. It is generally not recommended to
change any of these values without proper guidance and sufficient testing. Some
networks may require larger values if suffering from frequent reconfigurations.
Some applications may require faster failure detection times which can be achieved
by reducing the token timeout.
token This timeout is used directly or as a base for real token timeout calculation
(explained in token_coefficient section). Token timeout specifies in milliseconds
until a token loss is declared after not receiving a token. This is the time spent
detecting a failure of a processor in the current configuration. Reforming a new
configuration takes about 50 milliseconds in addition to this timeout.
For real token timeout used by totem it's possible to read cmap value of
runtime.config.totem.token key.
Be careful to use the same timeout values on each of the nodes in the cluster or
unpredictable results may occur.
The default is 3000 milliseconds.
token_warning
Specifies the interval between warnings that the token has not been received. The
value is a percentage of the token timeout and can be set to 0 to disable warnings.
The default is 75%.
token_coefficient
This value is used only when nodelist section is specified and contains at least 3
nodes. If so, real token timeout is then computed as token + (number_of_nodes - 2)
* token_coefficient. This allows cluster to scale without manually changing token
timeout every time new node is added. This value can be set to 0 resulting in
effective removal of this feature.
The default is 650 milliseconds.
token_retransmit
This timeout specifies in milliseconds after how long before receiving a token the
token is retransmitted. This will be automatically calculated if token is
modified. It is not recommended to alter this value without guidance from the
corosync community.
The minimum is 30 milliseconds. If not set and error occur, make sure token /
(token_retransmits_before_loss_const + 0.2) is more than 30.
The default is 238 milliseconds for two nodes cluster. Three or more nodes
reference token_coefficient.
knet_compression_model
Type of compression used by Kronosnet. Supported values depend on the libknet build
and on the installed compression libraries. Typically zlib and lz4 will be
available but bzip2 and others could also be allowed. The default is 'none'.
knet_compression_threshold
Tells knet to NOT compress any packets that are smaller than the value indicated.
Default 100 bytes.
Set to 0 to reset to the default. Set to 1 to compress everything.
knet_compression_level
Many compression libraries allow tuning of compression parameters. For example 0 or
1 ... 9 are commonly used to determine the level of compression. This value is
passed unmodified to the compression library so it is recommended to consult the
library's documentation for more detailed information.
hold This timeout specifies in milliseconds how long the token should be held by the
representative when the protocol is under low utilization. It is not recommended
to alter this value without guidance from the corosync community.
The default is 180 milliseconds.
token_retransmits_before_loss_const
This value identifies how many token retransmits should be attempted before forming
a new configuration. It is also used for token_retransmit and hold calculations.
The default is 4 retransmissions.
join This timeout specifies in milliseconds how long to wait for join messages in the
membership protocol.
The default is 50 milliseconds.
send_join
This timeout specifies in milliseconds an upper range between 0 and send_join to
wait before sending a join message. For configurations with less than 32 nodes,
this parameter is not necessary. For larger rings, this parameter is necessary to
ensure the NIC is not overflowed with join messages on formation of a new ring. A
reasonable value for large rings (128 nodes) would be 80msec. Other timer values
must also change if this value is changed. Seek advice from the corosync mailing
list if trying to run larger configurations.
The default is 0 milliseconds.
consensus
This timeout specifies in milliseconds how long to wait for consensus to be
achieved before starting a new round of membership configuration. The minimum
value for consensus must be 1.2 * token. This value will be automatically
calculated at 1.2 * token if the user doesn't specify a consensus value.
For two node clusters, a consensus larger than the join timeout but less than token
is safe. For three node or larger clusters, consensus should be larger than token.
There is an increasing risk of odd membership changes, which still guarantee
virtual synchrony, as node count grows if consensus is less than token.
The default is 3600 milliseconds.
merge This timeout specifies in milliseconds how long to wait before checking for a
partition when no multicast traffic is being sent. If multicast traffic is being
sent, the merge detection happens automatically as a function of the protocol.
The default is 200 milliseconds.
downcheck
This timeout specifies in milliseconds how long to wait before checking that a
network interface is back up after it has been downed.
The default is 1000 milliseconds.
fail_recv_const
This constant specifies how many rotations of the token without receiving any of
the messages when messages should be received may occur before a new configuration
is formed.
The default is 2500 failures to receive a message.
seqno_unchanged_const
This constant specifies how many rotations of the token without any multicast
traffic should occur before the hold timer is started.
The default is 30 rotations.
heartbeat_failures_allowed
[HeartBeating mechanism] Configures the optional HeartBeating mechanism for faster
failure detection. Keep in mind that engaging this mechanism in lossy networks
could cause faulty loss declaration as the mechanism relies on the network for
heartbeating.
So as a rule of thumb use this mechanism if you require improved failure in low to
medium utilized networks.
This constant specifies the number of heartbeat failures the system should tolerate
before declaring heartbeat failure e.g 3. Also if this value is not set or is 0
then the heartbeat mechanism is not engaged in the system and token rotation is the
method of failure detection
The default is 0 (disabled).
max_network_delay
[HeartBeating mechanism] This constant specifies in milliseconds the approximate
delay that your network takes to transport one packet from one machine to another.
This value is to be set by system engineers and please don't change if not sure as
this effects the failure detection mechanism using heartbeat.
The default is 50 milliseconds.
window_size
This constant specifies the maximum number of messages that may be sent on one
token rotation. If all processors perform equally well, this value could be large
(300), which would introduce higher latency from origination to delivery for very
large rings. To reduce latency in large rings(16+), the defaults are a safe
compromise. If 1 or more slow processor(s) are present among fast processors,
window_size should be no larger than 256000 / netmtu to avoid overflow of the
kernel receive buffers. The user is notified of this by the display of a
retransmit list in the notification logs. There is no loss of data, but
performance is reduced when these errors occur.
The default is 50 messages.
max_messages
This constant specifies the maximum number of messages that may be sent by one
processor on receipt of the token. The max_messages parameter is limited to 256000
/ netmtu to prevent overflow of the kernel transmit buffers.
The default is 17 messages.
miss_count_const
This constant defines the maximum number of times on receipt of a token a message
is checked for retransmission before a retransmission occurs. This parameter is
useful to modify for switches that delay multicast packets compared to unicast
packets. The default setting works well for nearly all modern switches.
The default is 5 messages.
knet_pmtud_interval
How often the knet PMTUd runs to look for network MTU changes. Value in seconds,
default: 30
knet_mtu
Switch between manual and automatic MTU discovery. A value of 0 means automatic,
other values set a manual MTU. In a setup with multiple interfaces, please specify
the lowest MTU of the selected interfaces.
The default value is 0.
block_unlisted_ips
Allow UDPU and KNET to drop packets from IP addresses that are not known (nodes
which don't exist in the nodelist) to corosync. Value is yes or no.
This feature is mainly to protect against the joining of nodes with outdated
configurations after a cluster split. Another use case is to allow the atomic
merge of two independent clusters.
Changing the default value is not recommended, the overhead is tiny and an existing
cluster may fail if corosync is started on an unlisted node with an old
configuration.
The default value is yes.
cancel_token_hold_on_retransmit
Allows Corosync to hold token by representative when there is too much retransmit
messages. This allows network to process increased load without overloading it.
Used mechanism is same as described for hold directive.
Some deployments may prefer to never hold token when there is retransmit messages.
If so, option should be set to yes.
The default value is no.
Within the logging directive, there are several configuration options which are all
optional.
The following 3 options are valid only for the top level logging directive:
timestamp
This specifies that a timestamp is placed on all log messages. It can be one of off
(no timestamp), on (second precision timestamp) or hires (millisecond precision
timestamp - only when supported by LibQB).
The default is hires (or on if hires is not supported).
fileline
This specifies that file and line should be printed.
The default is off.
function_name
This specifies that the code function name should be printed.
The default is off.
blackbox
This specifies that blackbox functionality should be enabled.
The default is on.
The following options are valid both for top level logging directive and they can be
overridden in logger_subsys entries.
to_stderr
to_logfile
to_syslog
These specify the destination of logging output. Any combination of these options
may be specified. Valid options are yes and no.
The default is syslog and stderr.
Please note, if you are using to_logfile and want to rotate the file, use
logrotate(8) with the option copytruncate. eg.
/var/log/corosync.log {
missingok
compress
notifempty
daily
rotate 7
copytruncate
}
logfile
If the to_logfile directive is set to yes , this option specifies the pathname of
the log file.
No default.
logfile_priority
This specifies the logfile priority for this particular subsystem. Ignored if debug
is on. Possible values are: alert, crit, debug (same as debug = on), emerg, err,
info, notice, warning.
The default is: info.
syslog_facility
This specifies the syslog facility type that will be used for any messages sent to
syslog. options are daemon, local0, local1, local2, local3, local4, local5, local6
& local7.
The default is daemon.
syslog_priority
This specifies the syslog level for this particular subsystem. Ignored if debug is
on. Possible values are: alert, crit, debug (same as debug = on), emerg, err,
info, notice, warning.
The default is: info.
debug This specifies whether debug output is logged for this particular logger. Also can
contain value trace, what is highest level of debug information.
The default is off.
Within the logging directive, logger_subsys directives are optional.
Within the logger_subsys sub-directive, all of the above logging configuration options are
valid and can be used to override the default settings. The subsys entry, described
below, is mandatory to identify the subsystem.
subsys This specifies the subsystem identity (name) for which logging is specified. This
is the name used by a service in the log_init() call. E.g. 'CPG'. This directive is
required.
Within the quorum directive it is possible to specify the quorum algorithm to use with the
provider
directive. At the time of writing only corosync_votequorum is supported. See
votequorum(5) for configuration options.
Within the nodelist directive it is possible to specify specific information about nodes
in cluster. Directive can contain only node sub-directive, which specifies every node that
should be a member of the membership, and where non-default options are needed. Every node
must have at least ring0_addr field filled.
Every node that should be a member of the membership must be specified.
Possible options are:
ringX_addr
This specifies IP or network hostname address of the particular node. X is a link
number.
nodeid This configuration option is required for each node for Kronosnet mode. It is a 32
bit value specifying the node identifier delivered to the cluster membership
service. The node identifier value of zero is reserved and should not be used. If
knet is set, this field must be set.
name This option is used mainly with knet transport to identify local node. It's also
used by client software (pacemaker). Algorithm for identifying local node is
following:
1. Looks up $HOSTNAME in the nodelist
2. If this fails strip the domain name from $HOSTNAME and looks up that in the
nodelist
3. If this fails look in the nodelist for a fully-qualified name whose short
version matches the short version of $HOSTNAME
4. If all this fails then search the interfaces list for an address that
matches a name in the nodelist
Within the system directive it is possible to specify system options.
Possible options are:
qb_ipc_type
This specifies type of IPC to use. Can be one of native (default), shm and socket.
Native means one of shm or socket, depending on what is supported by OS. On systems
with support for both, SHM is selected. SHM is generally faster, but need to
allocate ring buffer file in /dev/shm.
sched_rr
Should be set to yes (default) if corosync should try to set round robin realtime
scheduling with maximal priority to itself. When setting of scheduler fails,
fallback to set maximal priority.
priority
Set priority of corosync process. Valid only when sched_rr is set to no. Can be
ether numeric value with similar meaning as nice(1) or max / min meaning maximal /
minimal priority (so minimal / maximal nice value).
move_to_root_cgroup
Can be one of yes (Corosync always moves itself to root cgroup), no (Corosync never
tries to move itself to root cgroup) or auto (Corosync first checks if sched_rr is
enabled, and if so, it tries to set round robin realtime scheduling with maximal
priority to itself. If setting of priority fails, corosync tries to move itself to
root cgroup and retries setting of priority).
This feature is available only for systems with cgroups v1 with RT sched enabled
(Linux with CONFIG_RT_GROUP_SCHED kernel option) and cgroups v2.
It's worth noting that currently (May 3 2021) cgroup2 doesn’t yet support control
of realtime processes and the cpu controller can only be enabled when all RT
processes are in the root cgroup (applies only for kernel with
CONFIG_RT_GROUP_SCHED enabled). So when move_to_root_cgroup is disabled, kernel is
compiled with CONFIG_RT_GROUP_SCHED and systemd is used, it may be impossible to
make systemd options like CPUQuota working correctly until corosync is stopped.
Also when moving to root cgroup is enforced and used together with cgroup2 and
systemd it makes impossible (most of the time) for journald to add systemd specific
metadata (most importantly _SYSTEMD_UNIT) properly, because corosync is moved out
of cgroup created by systemd. This means it is not possible to filter corosync
logged messages based on these metadata (for example using -u or _SYSTEMD_UNIT=UNIT
pattern) and also running systemctl status doesn't display (all) corosync log
messages. The problem is even worse because journald caches pid for some time
(approx. 5 sec) so initial corosync messages have correct metadata.
allow_knet_handle_fallback
If knet handle creation fails using privileged operations, allow fallback to
creating knet handle using unprivileged operations. Defaults to no, meaning if
privileged knet handle creation fails, corosync will refuse to start.
The knet handle will always be created using privileged operations if possible,
setting this to yes only allows fallback to unprivileged operations. This fallback
may result in performance issues, but if running in an unprivileged environment,
e.g. as a normal user or in unprivileged container, this may be required.
state_dir
Existing directory where corosync should chdir into. Corosync stores important
state files and blackboxes there.
The default is /var/lib/corosync.
Within the resources directive it is possible to specify options for resources.
Possible option is:
watchdog_device
(Valid only if Corosync was compiled with watchdog support.)
Watchdog device to use, for example /dev/watchdog. If unset, empty or "off", no
watchdog is used.
In a cluster with properly configured power fencing a watchdog provides no
additional value. On the other hand, slow watchdog communication may incur multi-
second delays in the Corosync main loop, potentially breaking down membership.
IPMI watchdogs are particularly notorious in this regard: read about
kipmid_max_busy_us in IPMI.txt in the Linux kernel documentation.
Within the nozzle directive it is possible to specify options for a libnozzle device. This
is a pseudo ethernet device that routes network traffic through a channel on the corosync
knet network (NOT cpg or any corosync internal service) to other nodes in the cluster.
This allows applications to take advantage of knet features such as multipathing,
automatic failover, link switching etc. Note that libnozzle is not a reliable transport,
but you can tunnel TCP through it for reliable communications.
libnozzle also supports optional interface up/down scripts that are kept under a
/etc/corosync/updown.d/ directory. See the knet documentation for more information.
Only one nozzle device is allowed.
The nozzle stanza takes several options:
name The name of the network device to be created. On Linux this may be any name at all,
other platforms have restrictions on the name.
ipaddr The IP address (IPv6 or IPv4) of the interface. The bottom part of this address
will be replaced by the local node's nodeid in conjunction with ipprefix. so, eg
ipaddr: 192.168.1.0 ipprefix: 24 will make nodeids 1,2,5 use IP addresses
192.168.1.1, 192.168.1.2 & 192.168.1.5. If a prefix length of 16 is used then the
bottom two bytes will be filled in with nodeid numbers. IPv6 addresses must end in
'::', the nodeid will be added after the two colons to make the local IP address.
Only one IP address is currently supported in the corosync.conf file. Additional IP
addresses can be added in the ifup script if necessary.
ipprefix
specifies the IP address prefix for the nozzle device (see above)
macaddr
Specifies the MAC address prefix for the nozzle device. As for the IP address, the
bottom part of the MAC address will be filled in with the node id. In this case no
prefix applies, the bottom two bytes of the MAC address will always be overwritten
with the node id. So specifying macaddr: 54:54:12:24:12:12 on nodeid 1 will result
in it having a MAC address of 54:54:12:24:00:01
TO ADD A NEW NODE TO THE CLUSTER
For example to add a node with address 10.24.38.108 with nodeid 3. The node has the name
NEW (in DNS or /etc/hosts) and is not currently running corosync. The current
corosync.conf nodelist looks like this:
nodelist {
node {
nodeid: 1
ring0_addr: 10.24.38.101
name: node1
}
node {
nodeid: 2
ring0_addr: 10.24.38.102
name: node2
}
}
Add a new entry for the node below the existing nodes. Node entries don't have to be in
nodeid order, but it will help keep you sane. So the nodelist now looks like this:
nodelist {
node {
nodeid: 1
ring0_addr: 10.24.38.101
name: node1
}
node {
nodeid: 2
ring0_addr: 10.24.38.102
name: node2
}
node {
nodeid: 3
ring0_addr: 10.24.38.108
name: NEW
}
}
This file must then be copied onto all three nodes - the existing two nodes, and the new
one. On one of the existing corosync nodes, tell corosync to re-read the updated config
file into memory:
corosync-cfgtool -R
This command only needs to be run on one node in the cluster. You may then start corosync
on the NEW node and it should join the cluster. If this doesn't work as expected then
check the communications between all three nodes is working, and check the syslog files on
all nodes for more information. It's important to note that the key bit of information
about a node failing to join might be on a different node than you expect.
TO REMOVE A NODE FROM THE CLUSTER
This is the reverse procedure to 'Adding a node' above. First you need to shut down the
node you will be removing from the cluster.
corosync-cfgtool -H
Then delete the nodelist stanza from corosync.conf and finally update corosync on the
remaining nodes by running
corosync-cfgtool -R
on one of them.
ADDRESS RESOLUTION
corosync resolves ringX_addr names/IP addresses using the getaddrinfo(3) call with respect
of totem.ip_version setting.
getaddrinfo() function uses a sophisticated algorithm to sort node addresses into a
preferred order and corosync always chooses the first address in that list of the required
family. As such it is essential that your DNS or /etc/hosts files are correctly
configured so that all addresses for ringX appear on the same network (or are reachable
with minimal hops) and over the same IP protocol. If this is not the case then some nodes
might not be able to join the cluster. It is possible to override the search order used by
getaddrinfo() using the configuration file /etc/gai.conf(5) if necessary, but this is not
recommended.
If there is any doubt about the order of addresses returned from getaddrinfo() then it
might be simpler to use IP addresses (v4 or v6) in the ringX_addr field.
FILES
/etc/corosync/corosync.conf
The corosync executive configuration file.
SEE ALSO
corosync_overview(7), votequorum(5), corosync-qdevice(8), logrotate(8) getaddrinfo(3)
gai.conf(5)