Provided by: hylafax-server_6.0.7-5build1_amd64 bug

NAME

       info - remote device capability database

DESCRIPTION

       The   info  subdirectory  in  the  HylaFAX  spooling  area  holds  information  about  the
       capabilities and status of devices that have  been  called.   One  file  exists  for  each
       device,  with  the filename created from the remote device's fully-qualified phone number.
       Files have a simple ASCII format.  Each line is of the form
            [&]tag: value
       where a tag identifies a capability and a value is either a  string,  number,  or  boolean
       value.   An  optional  ``&''  at  the  front of the line indicates that the tag's value is
       locked down and should not be  updated  by  the  server.   This  facility  is  useful  for
       restricting the capabilities used with a particular machine.

       The following items are recorded:
              Tag                   Type       Description
              calledBefore          boolean    device has previously answered at this number
              dialFailures          number     count of consecutive failed dial operations
              hasV34Trouble         boolean    there is difficulty sending to this destination with V.34
              hasV17Trouble         boolean    there is difficulty sending to this destination with V.17
              lastDialFailure       string     reason for last failed dial operation
              lastSendFailure       string     reason for last failed send attempt
              maxPageWidth          number     maximum page width in pixels in normal resolution
              maxPageLength         number     maximum page length in millimeters
              maxSignallingRate     string     maximum signalling rate (bits/sec) to use
              minScanlineTime       string     minimum scanline time
              pagerMaxMsgLength     number     length of longest allowed text message
              pagerPassword         string     password string send to service provider
              pagerSetupCmds        string     commands for setting up modem for a specific service provider
              pagerTTYParity        string     parity & # bits configuration for IXO/TAP communication
              pageSource            string     parameter to tell the paging central who we are
              pagingProtocol        string     protocol (IXO or UCP) for this provider
              remoteCSI             string     remote device Called Subscriber Identification
              remoteNSF             string     remote equipment Non-Standard Facilities information
              remoteDIS             string     remote Digital Identification Signal: capabilities
              sendFailures          number     count of consecutive failed send attempts
              supportsBatching      boolean    accepts batching protocol
              supportsHighRes       boolean    accepts 196 line/inch images (obsolete)
              supportsVRes          number     vertical resolution support bitmask
              supports2DEncoding    boolean    accepts Group 3 2D encoding
              supportsMMR           boolean    accepts Group 4 encoding
              supportsPostScript    boolean    accepts Adobe POSTSCRIPT transfer protocol

       The  HylaFAX  scheduler,  faxq(8),  uses  the  information  stored  in this directory when
       deciding if a call should be placed and when preparing documents for transmission.   If  a
       remote  device's  capabilities  are known, then document preparation is constrained and/or
       optimized according to the capabilities.  Otherwise, documents are prepared without regard
       for  the  remote  device's  capabilities  and  if a capability mismatch is encountered the
       session is terminated and  the  documents  are  reformatted  using  the  newly  discovered
       capabilities.

       The calledBefore item is used by faxsend to decide whether or not to redial a phone number
       when encountering certain errors.  For example, if a dialing command  results  in  a  ``NO
       CARRIER''  result,  then  the  number will not be retried unless the number has previously
       been dialed successfully.

       The minScanlineTime item indicates the minimum scanline time parameter used for  facsimile
       transmissions.    Acceptable   values   are:  ``0ms'',  ``5ms'',  ``10ms/5ms'',  ``10ms'',
       ``20ms/10ms'', ``20ms'', ``40ms/20ms'', and ``40ms''.  (Values of the form X/Y mean to use
       X for 98 lpi images and Y for 196 lpi images.)

       The  pagerTTYParity  item specifies the communication parameters to use when communicating
       with the IXO/TAP service provider.  Acceptable values are: ``even'' (7 bits, even parity),
       ``odd''  (7  bits, odd parity), and ``none'' (8 bits, no parity).  If nothing is specified
       then ``even'' is used per the standard.

       The pagerMaxMsgLength, pagerPassword, and pagerTTYParity items can be setup  according  to
       the requirements of a pager service provider; they typically are locked down so that their
       values are not lost during updates.

       The pagerSetupCmds can be used to define AT commands  for  setting  up  the  modem  for  a
       specific  service  provider.   This  value  overwrites  the  settings  defined in hylafax-
       config(5).

       The pageSource parameter can be used to tell the paging central who we  are.   It  usually
       contains  a SMS answerable mobile number. It is only used for the UCP part of sendpage(8).
       Note:  This parameter should be used from user-land sendpage(1) and will be removed later.

       The pagingProtocol defines which protocol, UCP or IXO, should be used to send the  message
       to the service provider. It defaults to ``ixo''; for UCP set ``ucp''.

NOTES

       faxsend, pagesend, and faxq automatically create and update entries in the info directory,
       as required.

       The data in this directory is simply a cache of remote capabilities and, except for locked
       down  items,  can  be  safely  purged  at  any  time.  The faxcron(8) script, for example,
       periodically purges unlocked entries in this directory that have not been accessed  in  30
       days.

       When  the  first batching attempt fails then supportsBatching is set to false.  It must be
       manually altered in order to re-enable batching to the destination.

       Restricting the capabilities used with a particular machine to a value  other  than  those
       that  are  mandatory can cause documents to be sent outside of an acceptable range for the
       receiver.

SEE ALSO

       faxcron(8), faxq(8), faxsend(8), pagesend(8), hylafax-config(5)

                                        February 10, 1996                         HYLAFAX-INFO(5)