Provided by: thinkfan_1.3.1-4_amd64 bug

NAME

       thinkfan.conf - YAML-formatted config for thinkfan(1)

DESCRIPTION

       YAML is a very powerful, yet concise notation for structured data.  Its full specification
       is available at https://yaml.org/spec/1.2/spec.html.  Thinkfan uses only a small subset of
       the full YAML syntax, so it may be helpful, but not strictly necessary for users to take a
       look at the spec.

       The most important thing to note  is  that  indentation  is  syntactically  relevant.   In
       particular,  tabs  should  not  be  mixed  with spaces.  We recommend using two spaces for
       indentation, like it is shown below.

       The thinkfan config has three main sections:

       sensors:   Where temperatures should be read from. All hwmon-style drivers are  supported,
                  as  well as /proc/acpi/ibm/thermal, and, depending on the compile-time options,
                  libatasmart (to read temperatures directly from hard disks) and NVML  (via  the
                  proprietary nvidia driver).

       fans:      Which  fans  should be used (currently only one allowed).  Support for multiple
                  fans is currently in development and planned for a future release.  Both hwmon-
                  style PWM controls and /proc/acpi/ibm/fan can be used.

       levels:    Maps  temperatures  to  fan  speeds.   A  “simple  mapping”  just specifies one
                  temperature as the lower and upper bound (respectively) for a given fan  speed.
                  In  a  “detailed  mapping”,  the  upper and lower bounds are specified for each
                  driver/sensor configured  under  sensors:.   This  mode  should  be  used  when
                  thinkfan  is monitoring multiple devices that can tolerate different amounts of
                  heat.

       Under each of these sections, there must be a  list  of  key-value  maps,  each  of  which
       configures a sensor driver, fan driver or fan speed mapping.

SENSOR & FAN DRIVERS

       For  thinkfan  to  work, it first needs to know which temperature sensor drivers and which
       fan drivers it should use.  The mapping between temperature readings  and  fan  speeds  is
       specified in a separate config section (see the FAN SPEEDS section below).

   Sensor Syntax
       The  entries under the sensors: section can specify hwmon, thinkpad_acpi, NVML or atasmart
       drivers, where the latter two must be enabled at compile-time.  There can  be  any  number
       (greater  than zero) and combination of hwmon, tpacpi, nvml and atasmart entries.  However
       there may be at most one instance of the tpacpi entry.

       sensors:
         - hwmon: hwmon-path
           name: hwmon-name
           indices: index-list
           correction: correction-list
           optional: bool-allow-errors

         - tpacpi: /proc/acpi/ibm/thermal
           indices: index-list
           correction: correction-list
           optional: bool-allow-errors

         - nvml: nvml-bus-id
           correction: correction-list
           optional: bool-allow-errors

         - atasmart: disk-device-file
           correction: correction-list
           optional: bool-allow-errors

         - ...

   Fan Syntax
       Currently, thinkfan supports only one fan, so there can be only one  entry  in  the  list.
       Support  for  multiple  fans is currently in development and planned for a future release.
       The fan is either an hwmon fan:

       fans:
         - hwmon: hwmon-path
           name: hwmon-name
           indices: index-list

       or a tpacpi fan:

       fans:
         - tpacpi: /proc/acpi/ibm/fan

   Values
       hwmon-path  There are three ways of specifying hwmon fans or sensors:

               1)  A    full    path    of    a    “temp*_input”    or    “pwm*”    file,    like
                   “/sys/class/hwmon/hwmon0/pwm1”  or  “/sys/class/hwmon/hwmon0/temp1_input”.  In
                   this case, the  “indices:  index-list”  and  “name:  hwmon-name”  entries  are
                   unnecessary since the path uniquely identifies a specific fan or sensor.

                   Note  that this method may lead to problems when the load order of the drivers
                   changes across bootups, because in the “hwmonX” folder name,  the  X  actually
                   corresponds to the load order.  Use method 2) or 3) to avoid this problem.

               2)  A   directory   that   contains   a   specific   hwmon   driver,  for  example
                   “/sys/devices/platform/nct6775.2592”.  Note that this path  does  not  contain
                   the  load-order  dependent  “hwmonX”  folder.   As  long as it contains only a
                   single hwmon driver/interface it is sufficient to specify the “indices: index-
                   list”  entry  to  tell  thinkfan  which  specific  sensors  to  use  from that
                   interface.  The “name: hwmon-name” entry is unnecessary.

               3)  A directory that contains multiple or all of the hwmon  drivers,  for  example
                   “/sys/class/hwmon”.   Here,  both  the “name: hwmon-name” and “indices: index-
                   list” entries are required to tell thinkfan which interface  to  select  below
                   that path, and which sensors or which fan to use from that interface.

       hwmon-name  The  name of a hwmon interface, typically found in a file called “name”.  This
                   has to be specified if hwmon-path  is  a  base  path  that  contains  multiple
                   hwmons.   This method of specifying sensors is particularly useful if the full
                   path to a particular  hwmon  keeps  changing  between  bootups,  e.g.  due  to
                   changing load order of the driver modules.

       index-list  A  YAML  list [ X1, X2, ... ] that specifies which sensors, resp. which fan to
                   use from a given interface.  Both /proc/acpi/ibm/thermal and also  many  hwmon
                   interfaces  contain  multiple sensors, and not all of them may be relevant for
                   fan control.

                •  For hwmon entries, this is required if hwmon-path does not refer directly to a
                   single “tempXi_input” file, but to a folder that contains one or more of them.
                   In this case, index-list specifies the Xi for the  “tempXi_input”  files  that
                   should  be used.  A hwmon interface may also contain multiple PWM controls for
                   fans, so in that case, index-list must contain exactly one entry.

                •  For  tpacpi  sensors,  this  entry  is  optional.   If  it  is  omitted,   all
                   temperatures found in /proc/acpi/ibm/thermal will be used.

       nvml-bus-id NOTE: only available if thinkfan was compiled with USE_NVML enabled.

                   The  PCI  bus  ID  of an nVidia graphics card that is run with the proprietary
                   nVidia driver. Can be obtained with e.g. “lspci  |  grep  -i  vga”.   Usually,
                   nVidia  cards  will  use  the open source nouveau driver, which should support
                   hwmon sensors instead.

       disk-device-file
                   NOTE: only available if thinkfan was compiled with USE_ATASMART enabled.

                   Full path to a device file for a hard disk that supports S.M.A.R.T.  See  also
                   the  -d  option  in thinkfan(1) that prevents thinkfan from waking up sleeping
                   (mechanical) disks to read their temperature.

       correction-list (always optional)
                   A YAML list that specifies temperature offsets for each sensor in use  by  the
                   given  driver. Use this if you want to use the “simple” level syntax, but need
                   to compensate for devices with a lower heat tolerance.  Note however that  the
                   detailed level syntax is usually the better (i.e. more fine-grained) choice.

       bool-allow-errors (always optional, false by default)
                   A  truth  value  (yes/no/true/false)  that  specifies  whether thinkfan should
                   accept errors when reading from this sensor.   Normally,  thinkfan  will  exit
                   with  an  error  message if reading the temperature from any configured sensor
                   fails.  Marking a sensor as optional may be useful for removable  hardware  or
                   devices that may get switched off entirely to save power.

FAN SPEEDS

       The  levels:  section  specifies  a  list  of  fan  speeds with associated lower and upper
       temperature bounds.  If temperature(s) drop below the lower bound,  thinkfan  switches  to
       the  previous  level,  and  if  the  upper bound is reached, thinkfan switches to the next
       level.

   Simple Syntax
       In the simplified form, only one temperature is specified as an upper/lower  limit  for  a
       given  fan  speed.  In that case, the lower-bound and upper-bound are compared only to the
       highest temperature found among  all  configured  sensors.   All  other  temperatures  are
       ignored.   This  mode is suitable for small systems (like laptops) where there is only one
       device (e.g. the CPU) whose temperature needs to be controlled, or where the required  fan
       behaviour is similar enough for all heat-generating devices.

       levels:
         - [ fan-speed, lower-bound, upper-bound ]
         - ...

   Detailed Syntax
       This  mode  is  suitable  for  more  complex  systems,  with  devices  that have different
       temperature ratings.  For example, many modern CPUs and GPUs can  deal  with  temperatures
       above  80°C  on  a  daily  basis,  whereas a hard disk will die quickly if it reaches such
       temperatures.  In detailed mode, upper and lower temperature limits are specified for each
       sensor individually:

       levels:
         - speed: fan-speed
           lower_limit: [ l1, l2, ... ]
           upper_limit: [ u1, u2, ... ]
         - ...

   Values
       fan-speed   The possible speed values are different depending on which fan driver is used.

                   For  a  hwmon  fan,  fan-speed  is  a  numeric  value  ranging  from 0 to 255,
                   corresponding to the PWM values accepted by the various kernel drivers.

                   For a tpacpi fan on Lenovo/IBM ThinkPads and some other  Lenovo  laptops  (see
                   SENSORS  &  FAN  DRIVERS  above), numeric values and strings can be used.  The
                   numeric values range from 0 to 7.  The string values take the form "level lvl-
                   id",  where lvl-id may be a value from 0 to 7, auto, full-speed or disengaged.
                   The numeric values 0 to 7 correspond to the regular fan  speeds  used  by  the
                   firmware,  although  many  firmwares don't even use level 7.  The value "level
                   auto" gives control back to the firmware, which  may  be  useful  if  the  fan
                   behavior  only  needs  to  be  changed for certain specific temperature ranges
                   (usually at the high and low end of the range).  The values "level full-speed"
                   and  "level  disengaged"  take  the  fan speed control away from the firmware,
                   causing the fan to slowly ramp up to an absolute maximum that can be  achieved
                   within   electrical   limits.   Note  that  this  will  run  the  fan  out  of
                   specification and cause increased wear, though it may  be  helpful  to  combat
                   thermal throttling.

       l1, l2, ...

       u1, u2, ... The  lower  and  upper  limits refer to the sensors in the same order in which
                   they were found when processing the sensors: section (see SENSOR & FAN DRIVERS
                   above).   For  the  first level entry, the lower_limit may be omitted, and for
                   the last one, the upper_limit may be omitted.  For all levels in between,  the
                   lower limits must overlap with the upper limits of the previous level, to make
                   sure the entire temperature range is covered and that there is some hysteresis
                   between speed levels.

SEE ALSO

       The thinkfan manpage:
       thinkfan(1)

       Example configs shipped with the source distribution, also available at:
       https://github.com/vmatare/thinkfan/tree/master/examples

       The Linux hwmon user interface documentation:
       https://www.kernel.org/doc/html/latest/hwmon/sysfs-interface.html

       The thinkpad_acpi interface documentation:
       https://www.kernel.org/doc/html/latest/admin-guide/laptops/thinkpad-acpi.html

BUGS

       Report bugs on the github issue tracker:
       https://github.com/vmatare/thinkfan/issues